qca6174 with wmi-tlv firmware uses offloaded
beaconing scheme (i.e. templates). This requires a
little different approach when implementing CSA.

Add missing code to update CS count and report CSA
completion to mac80211. Without it channel switch
was never finished.

To avoid races during interface teardown data_lock
has been used to protect is_up and is_started so
they can be compared against before scheduling
count down work.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The current SKID length configuration causes firmware
to reject peer creation for not able to allocate
AST entries for peers. This issue is observed when
least significant 3 bytes are used ramdomly to create
client MAC addresses.

AST table SKID length configuration is increased to
maximum value to fix this issue.
Signed-off-by: NSenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware reports chirp status in phy error event if it's detected
and the chirp status is valuable to distinguish radar types.
So save it to use for DFS parttern detector.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Having lower number of copy engine entries for target to host
WMI ring is causing drops in receiving management frames. This
issue is observed during max clients (128 clients) stress testing.
While bursting deauthentication frames from simulated clients,
approx. 70% of frames are getting dropped due to lower ring entries.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Not all firmware revisions have a proper
multi-interface client powersaving implementation,
e.g. qca6174 WLAN.RM.2.0-00073.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca6184 WLAN.RM.2.0-00073 has a bug in sta
powersave state machine and requires peer param to
be poked to enable the powersave.

Calling this unconditionally should be safe for
other chips/firmwares.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

During wmm tests changing wmm parameters did not change anything.
This was because of mismatch in WMM params per vdev command.
WMM params per vdev uses different command structure than wmm params
per pdev command.

Patch concerns qca6174.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca6174 WLAN.RM.2.0-00073 firmware uses full rx
reordering offload and delivers Rx via a new HTT
event. The event however is incorrectly generated
in firmware and becomes overly long (with trailing
garbage). This was hitting defined CE buffer limit
that was programmed to the device and caused
device to crash upon busier Rx traffic.

Increasing the CE buffer limit for HTT Rx pipe to
2KBytes seems to be enough to workaround this
problem.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If firmware advertises support for TxBF then the
driver has to instruct the firmware accordingly
during runtime. Without this patch connecting to
an AP with beamformer support would yield abysmal
Rx performance.

This has been tested with wmi-tlv and qca6174
while acting as a STA beamformee only.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This processes and pushes fw stats to the debug
module (if enabled).

Changing the generic ath10k_wmi_requests_stats()
call to use more stat bits has no effect on older
firmware binaries.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New qca6174 wmi-tlv firmware revisions support
more stat event bits.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The expected parameter is not a single value but a
mask of values.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New qca6174 wmi-tlv firmware supports vdev stats.
This patch adds support for it in the debug
frontend.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some firmware revisions don't notify host about
self-bss-peer removal until after associated vdev
is deleted. This has been observed with qca6174
WLAN.RM.2.0-00073 firmware.

This patch fixes AP teardown slowdowns and
prevents delays and warnings:

 ath10k_pci 0000:00:05.0: failed to remove peer for AP vdev 0: -110
 ath10k_pci 0000:00:05.0: removing stale peer xx:xx:xx:xx:xx:xx from vdev_id 0
 ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 24
 ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 8
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The value was off by one.  The error probably has no negative
affect on any upstream firmware, but should be fixed anyway
in case it comes into use in the future.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix spelling error.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

A bit of general cleanup to make debug messages more useful.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case firmware fails to start the scan, then complete
the start condition and clean up so that driver does not
block on timeout.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The 3.2 revision has a different target BMI
version so it wasn't recognized by ath10k (despite
the chip_id rev being on the supported list
already).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Introduce an optional log level configuration for the existing debugfs fw_dbglog file. It
allows users to configure the desired log level for firmware dbglog messages.

To configure log level as WARN:

echo 0xffffffff  2 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog

The values are:

VERBOSE		0
INFO		1
WARN		2
ERR		3
Signed-off-by: NSenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Otherwise ath10k will just checksum everything even if it did not
go through the TCP/IP stack (for example bridged frames). In the worst
case this could mean recreating the checksum for incorrect data.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This should fix a very rare occurrence of the following deadlock:

  [<ffffffffa018265e>] ath10k_wmi_tx_beacons_nowait+0x1e/0x50 [ath10k_core]
  [<ffffffffa01829b6>] ath10k_wmi_op_ep_tx_credits+0x16/0x40 [ath10k_core]
  [<ffffffffa017d685>] ath10k_htc_send+0x285/0x3d0 [ath10k_core]
  [<ffffffffa0184b81>] ath10k_wmi_cmd_send_nowait+0x81/0x110 [ath10k_core]
  [<ffffffffa0184c61>] ath10k_wmi_tx_beacon_nowait.part.33+0x51/0x90 [ath10k_core]
  [<ffffffffa0184cd0>] ath10k_wmi_tx_beacons_iter+0x30/0x40 [ath10k_core]
  [<ffffffff81882246>] __iterate_active_interfaces+0xa6/0x100
  [<ffffffffa0184ca0>] ? ath10k_wmi_tx_beacon_nowait.part.33+0x90/0x90 [ath10k_core]
  [<ffffffff818822ae>] ieee80211_iterate_active_interfaces_atomic+0xe/0x10
  [<ffffffffa0182676>] ath10k_wmi_tx_beacons_nowait+0x36/0x50 [ath10k_core]
  [<ffffffffa01829b6>] ath10k_wmi_op_ep_tx_credits+0x16/0x40 [ath10k_core]
  [<ffffffffa017d140>] ath10k_htc_rx+0x280/0x410 [ath10k_core]
  [<ffffffffa01bcbf0>] ? ath10k_ce_completed_recv_next+0x60/0x80 [ath10k_pci]
  [<ffffffffa01bc6ab>] ath10k_pci_ce_recv_data+0x11b/0x1d0 [ath10k_pci]
  [<ffffffffa01bcf44>] ath10k_ce_per_engine_service+0x64/0xc0 [ath10k_pci]
  [<ffffffffa01bcfc2>] ath10k_ce_per_engine_service_any+0x22/0x50 [ath10k_pci]
  [<ffffffffa01bc4d0>] ath10k_pci_tasklet+0x30/0x90 [ath10k_pci]
  [<ffffffff81055a55>] tasklet_action+0xc5/0x100

To prevent this make sure to release ar->data_lock
while calling to ath10k_wmi_beacon_send_ref_nowait().
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The command logic shouldn't really care about
arvif structure.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Ath10k driver sets wrong default key idx that results in
sending unicast frames with multicast key.

The reason for this behavior is that cached broadcast key
is installed for station MAC address on association. After
dot1x completes, unicast key is installed for station
MAC address. Default key idx is set to broadcast key id when
driver tries to send broadcast frame. This causes firmware
to use broadcast key id to transmit unicast frames to stations.

Used TX_USAGE flag to set default key for stations.

Added callback for setting unicast default idx which will be
invoked on every default key idx configuration.
Signed-off-by: NSenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

During drv_start/drv_stop stress testing in ARM platform,
sometimes target is taking more that 5ms to wake up. Similar
behaviour also noted during driver load and unload iterations.
On such cases, the wakup duration lies between 5-6ms. Hence
increasing pci wakup timeout 10ms to be more safer. With this
changes, able to complete power down/up >100 iterations without
any issues.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable the MCS8 and MCS9 support for 2.4G band, it will
use these data rate with other devices having the same
capability.
Signed-off-by: NYanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware revisions providing sta keepalive service
have it enabled by default.

mac80211 already does idle connection polling so
it makes no sense to duplicate this in ath10k.
mac80211 wouldn't even know of the offloaded
keepalive NullFunc frames.

This prevents sending out some extraneous frames
on the air.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New wmi-tlv firmware for qca6174 has STA keepalive
service available. The service can provide
automatic idle connection polling via NullFunc
frames to AP when acting as a client.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New wmi-tlv firmware for qca6174 supports this.

This should fix issues related to multi-vif WMM.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New wmi-tlv firmware for qca6174 supports this.
This will be used soon.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

mac80211 already requests WMM per vif but firmware
wasn't able to handle this until now. However new
wmi-tlv firmware for qca6174 is capable of this.

This prepares per-vif WMM param setup.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New wmi-tlv firmware uses HTT 3.0 protocol which
uses TX_FRM command for management frames (instead
of a dedicated command). To support PMF it is
necessary to provide explicit tailroom.
Signed-off-by: NMarek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Software encryption was never necessary.
Tested with fw 636 and fw 10.x.
Signed-off-by: NMarek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It makes little sense to keep handling irqs if fw
is dead.

This prevents multiple fw register dumps upon
crash on some devices (seen on QCA6174).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Only userspace can make an educated decision when
a trigger frame is required so make sure the
autotrigger service is disabled.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New wmi-tlv firmware for qca6174 has u-UAPSD
autotrigger service. If it is enabled firmware
generates trigger frames automatically as
configured.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The workaround couldn't work correctly because the
802.11 header wasn't properly stripped of QoS Data
bit so it wasn't recognized in the later parts of
tx path as NullFunc frame and ended up in HTT Tx
instead of HTT Mgmt Tx.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware supporting beacon templates (i.e. wmi-tlv
for qca6174) doesn't implicitly take dtim period
from the template. Instead it requires vdev param
to be set accordingly.

This fixes dtim period being stuck at 3.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

HTT Tx protocol uses arbitrary host assigned ids
too associate with MSDUs when delivering
completions.

Instead of rolling out own id generation scheme
use the tools provided in kernel.

This should have little to no effect on
performance.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>