Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Currently just hooked up to the already-existing nouveau_hw, which should
handle all relevant chipsets as well as we currently can.

This will likely be eventually split out and improved into chipset specific
code at a later point.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This will make nouveau_pm attempt to report the card's current performance
level both during bootup, and through sysfs.

This is a very initial implementation, and can be improved a *lot*
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Instead of emptying the caches to avoid a race with the PFIFO puller,
go straight ahead and try to recover from it when it happens. Also,
kill pfifo->cache_flush and tile->lock, we don't need them anymore.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

nouveau_load() just returned directly if there was an error instead of
releasing resources.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Reviewed-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Fixes the randomly flashing vertical lines seen on some nv3x after a
cold-boot.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

In some situations it's possible we can receive a spurious hotplug IRQ
before we're ready to handle it, leading to an oops.

Calling the display init before enabling interrupts should clear any
pending IRQs on the GPU and prevent this from happening.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This removes the previous prepare_access() and finish_access() hooks, and
replaces it with a much simpler flush() hook.

All the chipset-specific code before nv50 has its use removed completely,
as it's not required there at all.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Nouveau will no longer load at all if card initialisation fails, so all
these checks are unnecessary.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

It's far preferable to have the driver do nothing at all for "nomodeset".
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

On cards where there's a specific BAR for PRAMIN, we used to try and fall
back to the "legacy" aperture within the mmio BAR.

This is doomed to cause problems, so lets just fail completely as there's
obviously something else very wrong anyway.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Because we aren't in a suspend state the poll will still run when we have switcherooed a card off.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This will be useful for computing GPU-CPU latency, including
GL_ARB_timer_query extension.
Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.

v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.

v3: add config lock take inside polling, add intel/nouveau poll init/fini calls

v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.

glisse: discard drm_helper_hpd_irq_event

v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

let vga16fb claim 0xA0000+0x10000 region as its aperture;
drm drivers don't use it, so we have to detect it and kick
vga16fb manually - but only if drm is driving the primary card
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Currently vesafb/efifb/... is kicked when hardware driver is registering
framebuffer. To do it hardware must be fully functional, so there's a short
window between start of initialisation and framebuffer registration when
two drivers touch the hardware. Unfortunately sometimes it breaks nouveau
initialisation.

Fix it by kicking firmware driver(s) before we start touching the hardware.
Reported-by: NDidier Spaier <didier.spaier@epsm.fr>
Tested-by: NDidier Spaier <didier.spaier@epsm.fr>
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

As opposed to repeatedly reading the amount back from the GPU every
time we need to know the VRAM size.

We should now fail to load gracefully on detecting no VRAM, rather than
something potentially messy happening.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The fbdev layer in the kms code should act like a consumer of the kms services and avoid having relying on information being store in the kms core structures in order for it to work.

This patch

a) removes the info pointer/psuedo palette from the core drm_framebuffer structure and moves it to the fbdev helper layer, it also removes the core drm keeping a list of kernel kms fbdevs.
b) migrated all the fb helper functions out of the crtc helper file into the fb helper file.
c) pushed the fb probing/hotplug control into the driver
d) makes the surface sizes into a structure for ease of passing
This changes the intel/radeon/nouveau drivers to use the new helper.
Signed-off-by: NDave Airlie <airlied@redhat.com>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

This makes nouveau recognise and report more kinds of PGRAPH errors, as
well as prevent GPU lockups resulting from some of them.

Lots of guesswork was involved and some part of this is probably
incorrect. Some potential-lockuop situations are handled by just
resetting a whole PGRAPH subunit, which doesn't sound like a "proper"
solution, but seems to work just fine... for now.
Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Many new laptops now come with 2 gpus, one to be used for low power
modes and one for gaming/on-ac applications. These GPUs are typically
wired to the laptop panel and VGA ports via a multiplexer unit which
is controlled via ACPI methods.

4 combinations of systems typically exist - with 2 ACPI methods.
Intel/ATI - Lenovo W500/T500 - use ATPX ACPI method
ATI/ATI - some ASUS - use ATPX ACPI Method
Intel/Nvidia - - use _DSM ACPI method
Nvidia/Nvidia -  - use _DSM ACPI method.

TODO:
This patch adds support for the ATPX method and initial bits
for the _DSM methods that need to written by someone with
access to the hardware.
Add a proper non-debugfs interface - need to get some proper
testing first.

v2: add power up/down support for both devices
on W500 puts i915/radeon into D3 and cuts power to radeon.

v3: redo probing methods, no DMI list, drm devices call to
register with switcheroo, it tries to find an ATPX method on
any device and once there is two devices + ATPX it inits the
switcher.

v4: ATPX msg handling using buffers - should work on more machines

v5: rearchitect after more mjg59 discussion - move ATPX handling to
    radeon driver.

v6: add file headers + initial nouveau bits (to be filled out).

v7: merge delayed switcher code.

v8: avoid suspend/resume of gpu that is off

v9: rearchitect - mjg59 is always right. - move all ATPX code to
radeon, should allow simpler DSM also proper ATRM handling

v10: add ATRM support for radeon BIOS, add mutex to lock vgasr_priv

v11: fix bug in resuming Intel for 2nd time.

v12: start fixing up nvidia code blindly.

v13: blindly guess at finishing nvidia code

v14: remove radeon audio hacks - fix up intel resume more like upstream

v15: clean up printks + remove unnecessary igd/dis pointers

mount debugfs

/sys/kernel/debug/vgaswitcheroo/switch - should exist if ATPX detected
 + 2 cards.

DIS - immediate change to discrete
IGD - immediate change to IGD
DDIS - delayed change to discrete
DIGD - delayed change to IGD
ON - turn on not in use
OFF - turn off not in use

Tested on W500 (Intel/ATI) and T500 (Intel/ATI)
Signed-off-by: NDave Airlie <airlied@redhat.com>

This commit breaks the userspace interface, and requires a new libdrm for
nouveau to operate again.

The multiple GEM_PUSHBUF ioctls that were present in 0.0.15 for
compatibility purposes are now gone, and replaced with the new ioctl which
allows for multiple push buffers to be submitted (necessary for hw index
buffers in the nv50 3d driver) and relocations to be applied on any buffer.

A number of other ioctls (CARD_INIT, GEM_PIN, GEM_UNPIN) that were needed
for userspace modesetting have also been removed.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>

The nv50 pgraph handler (for example) could reenable pgraph fifo access
and that would be bad when pgraph context is being unloaded (we need the
guarantee a ctxprog isn't running).
Signed-off-by: NMaarten Maathuis <madman2003@gmail.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

On nv50, this will be needed by applications using CUDA to know
how much stack/local memory to allocate.
Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

noaccel=1 disables all acceleration and doesn't even attempt
initialising PGRAPH+PFIFO, nofbaccel=1 only makes fbcon unaccelerated.
Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Currently, we take down the sgdma engine without evicting all buffers
from VRAM.

The TTM device release will try to evict anything in VRAM to GART
memory, but this will fail since sgdma has already been taken down.

This causes an infinite loop in kernel mode on module unload.
It usually doesn't happen because there aren't any buffer on close.
However, if the GPU is locked up, this condition is easily triggered.

This patch fixes it in the simplest way possible by cleaning VRAM
right before cleaning SGDMA memory.
Signed-off-by: NLuca Barbieri <luca@luca-barbieri.com>
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>