While the DT parsing code recognizes "ok" as a valid value for the
"status" property, ePAPR v1.1 doesn't mention it in the list of valid
values.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The LEDs on the koelsch board are labeled using upper-case characters.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

DMA transfer uses DVC

     DMA               DMApp
[MEM] -> [SRC] -> [DVC] -> [SSIU] -> [SSI]

     DMA               DMApp
[MEM] <- [DVC] <- [SRC] <- [SSIU] <- [SSI]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

DMA transfer to/from SRC

     DMA      DMApp
[MEM] -> [SRC] -> [SSIU] -> [SSI]

     DMA      DMApp
[MEM] <- [SRC] <- [SSIU] <- [SSI]

Current sound driver is supporting
SSI/SRC random connection.
So, this patch is tring
SSI0 -> SRC2
SSI1 <- SRC3
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

DMA transfer to/from SSIU

     DMA
[MEM] -> [SSIU] -> [SSI]

     DMA
[MEM] <- [SSIU] <- [SSI]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

DMA transfer to/from SSI

     DMA
[MEM] -> [SSI]

     DMA
[MEM] <- [SSI]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Current Koelsch I2C2 has 400kHz settings,
but, ak4643 audio codec chip which is connected to I2C2 can't
work such frequency.
Fixup I2C2 clock frequency to 100kHz.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This appears to be the best match for ePAPR.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Koelsch is now restricted to booting from DT, so chosen/stdout-path is
always used, and we can drop the "console=" parameter from chosen/bootargs.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: devicetree@vger.kernel.org
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable HS-USB device for the Koelsch board, defining the GPIO that the driver
should check when probing (which is the ID output from MAX3355 OTG chip).

Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin function/group and prop, moved device node, fixed summary,
added changelog]
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable USB PHY device for the Koelsch board.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=" parameter in chosen/bootargs,
as this DTS is shared between legacy and multi-platform.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch series updates the device tree vendor prefix for
Dialog Semiconductor.

Various methods are currently used throughout the kernel: 'diasemi',
'dialog' and 'dlg'. Others have also been suggested.

This patch set aims to consolidate the usage of the vendor prefix to
use a common standard. The prefix 'dlg' is used.
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:

pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table

Remove it to fix this.

Fixes: commit 1d41f36a ("ARM: shmobile:
       koelsch dts: Add VDD MPU regulator for DVFS")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Define the Koelsch board dependent part of the VIN1 device node. Add the device
node for Analog  Devices ADV7180  video decoder to  I2C2 bus. Add the necessary
subnodes to interconnect VIN1 and ADV7180 devices.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

No more device needs to be added from platform code when booting the
reference platform, remove the now empty r8a7791_add_dt_devices()
function completely.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
[horms+renesas@verge.net.au: minor witespace changes]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

A second i2c6 node was a added by
05e234a187058ee ("ARM: shmobile: koelsch dts: Add VDD MPU regulator for
DVFS"). Merge this into the existing node.

Also shuffle i2c nodes so they are all together.

Cc: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.

- voltage-tolerance = 1%
  It reflects the tolerance for the CPU voltage defined inside the OPP
  table. Due to the lack of proper OPP definition, use an arbitrary safe
  value.
- clock-latency = 300 us
  Approximate worst-case latency to do a full DVFS transition for every
  OPPs. Due to the lack of HW information, use an arbitrary safe value.
  Note: The term transition-latency will be more accurate to define this
  value since the clock transition latency is not the only parameter that
  will define the overall DVFS transition.
- operating-points = < kHz - uV >
  List of 6 operating points. All of them are using the same voltage
  since DVS is not supported in R-CAR Gen2.
- clocks
  phandle to the CPU clock source. This clock source is used for all the
  2 CortexA15 located inside the same cluster.
Signed-off-by: NGaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The CA15 cluster is capable of voltage scaling. Add the regulator
in the i2c6 node, to allow the generic CPUFreq driver to use it.

Enable the i2c6 pin mux and the device node as well since the
da9210 is connected to that bus.

Note: In R-CAR Gen2, each frequency is using the same voltage,
and DVS control is not used. Therefore, this patch set the
voltage(Vmin/Vmax) to 1000mv.
Signed-off-by: NGaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

SCIF0 and SCIF1 are used as debug serial ports. Enable them and
configure pinmuxing appropriately. We can now remove the clkdev
registration hack for SCIF devices from the Koelsch reference board
file.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: added aliases to avoid device renumbering]
[horms+renesas@verge.net.au: resolved conflicts]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Fix typo of renesas,groups in the koeslch dt. The kernel has no
renesas,gpios but this should match renesas,groups.

Noticed thanks to similar fix for Lager by Rob Taylor and Ben Dooks.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This node should have a unique name so it can be distinguished when
other i2c busses are added later.
Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The Koelsch board uses the ethernet PHY LED0 as a link signal connected
to the ethernet controller. Specify the corresponding LED mode for the
PHY.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add DTS gpio-keys support for SW2 on the Koelsch board.
This makes the DT code match the legacy board code. Also
update the existing gpio-keys nodes to make use of KEY_n.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add pinctrl and SPI device for MSIOF on Koelsch.
On this board, only MSIOF0 is in use. Its bus contains a single device
(a Renesas R2A11302FT PMIC), for which no bindings are defined yet.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Prepare for the advent of MSIOF SPI, which will be spi1 to spi3.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add DT support for SDHI0, SDHI1 and SDHI2 on Koelsch.

The board specific handling of CD and WP pins are
using GPIOs. SDHI0 and SDHI1 are hooked up to regular
SD connectors while SDHI2 is using micro-SD which
is lacking WP signal.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Define the Koelsch board dependent part of the Ether device node.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Acked-by: NMagnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: resolved conflict]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The DU device has no DT bindings yet, instantiate it as a platform
device for now.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NMagnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: broken out of larger patch that
                             included board changes]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add pinctrl and SPI devices for QSPI on Koelsch.
Add Spansion s25fl512s SPI FLASH and MTD partitions.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This enables SATA0 in Koelsch device tree.
SATA1 is not available on Koelsch since
its pinmux configuration is fixed to PCIe.
Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Fix dts to have memory 1GiB @ 0_4000_0000 + 1GiB @ 2_0000_0000
according to Koelsch's hardware manual.
Signed-off-by: NTakashi Yoshii <takasi-y@ops.dti.ne.jp>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>