The added support for SPI mode made it possible to configure the driver
when I2C is disabled, leaving an unused device table:

drivers/rtc/rtc-rv3029c2.c:794:29: error: 'rv3029_id' defined but not used [-Werror=unused-variable]

This moves the table inside of the #ifdef section that has the
only user, to avoid the harmless warning.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: d08f50dd0afc ("rtc: rv3029: Add support of RV3049")
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The R2025SD chip, according to its data sheet, sets the /XST
bit to zero if the oscillator stops. Hence the check for this
condition was wrong.
Signed-off-by: NThomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add the alarm IRQ functionality.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The bin2bcd function in set_time is uncorrect on weekdays as the
bit mask should be done at the end of arithmetic operations.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The RTC RV3029 handles different types of alarms : seconds, minutes, ...
These alarms can be enabled or disabled individually using an AE_x bit
which is the last bit (BIT(7)) on each alarm registers.

To prepare the alarm IRQ support, the current code enables all the alarm
types by setting each AE_x to 1.
It also fixes others alarms issues :
   - month and weekday errors : it was performing -1 instead of +1.
   - wrong use of bit mask with bin2bcd
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Remove some checks from checkpatch such as spaces around arithmetic
operations or prefer "unsigned int".
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add support of Microcrystal RV3049 RTC (SPI) using regmap on the
RV3029 (I2C) driver.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

To add support of rv3049, the current driver is converted to use regmap.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

To prepare the use of regmap to add the support of RV-3049, all the
'i2c' in functions's names are removed.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

stmp3xxx_wdt_register() can fail as platform_device_alloc() or
platform_device_add() can fail. But when it fails it failed silently.
Lets print out an error message on failure so that user will atlest
know that there was some error.
Signed-off-by: NSudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The rtc->ops_lock would be accessed in ds3232_irq() without being
initialized as rtc_device_register() is called too late.

So move devm_rtc_device_register() just before registering irq handler
to initialize rtc->ops_lock earlier.
Signed-off-by: NGong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

If enable_irq_wake fails, we should return that error code so that
entering suspend fails. Otherwise we will get a WARNING along with
the hint of a unbalanced wake disable:
Unbalanced IRQ 37 wake disable
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

We program RTC time using SET_TIME_WRITE register and read the RTC
current time using CURRENT_TIME register. When we set the time by
writing into SET_TIME_WRITE Register and immediately try to read the
rtc time from CURRENT_TIME register, the previous old value is
returned instead of the new loaded time. This is because RTC takes
nearly 1 sec to update the  new loaded value into the CURRENT_TIME
register. This behaviour is expected in our RTC IP.

This patch updates the driver to read the current time from SET_TIME_WRITE
register instead of CURRENT_TIME when rtc time is requested within an 1sec
period after setting the RTC time. Doing so will ensure the correct time is
given to the user.

Since there is a delay of 1sec in updating the CURRENT_TIME we are loading
set time +1sec while programming the SET_TIME_WRITE register, doing this
will give correct time without any delay when read from CURRENT_TIME.
Signed-off-by: NAnurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Fix typo in interrupt-names
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The RTC core handles it since 6610e089 (RTC: Rework RTC code to use
timerqueue for events). So far, only the callbacks to the RTC core have
been removed, but not the handlers. Do this now.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The RTC core handles it since 6610e089 (RTC: Rework RTC code to use
timerqueue for events).
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

This flag is a no-op now (see commit 47b0eeb3 "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.

Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Michael Tatarinov <kukabu@gmail.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

This flag is a no-op now (see commit 47b0eeb3 "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.

Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

This flag is a no-op now (see commit 47b0eeb3 "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.

Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

It is suggested to program CALIB_WRITE register with the calibration
value before updating the SET_TIME_WRITE register, doing so will
clear the Tick Counter and force the next second to be signaled
exactly in 1 second.
Signed-off-by: NAnurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

In order to conserve battery energy, during the PS operation,
it is expected that the supply for the battery-powered domain
to be switched from the battery (VCC_PSBATT) to (VCC_PSAUX) and
automatically be switched back to battery when VCC_PSAUX voltage
drops below a limit, doing so prevents the logic within
the battery-powered domain from functioning incorrectly.
Signed-off-by: NAnurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

objtool reports the following warning:

  drivers/rtc/rtc-ds1685.o: warning: objtool: ds1685_rtc_poweroff() falls through to next function ds1685_rtc_work_queue()

Similar to commit 361c6ed6 ("rtc: ds1685: actually spin forever in
poweroff error path"), there's another unreachable() annotation which is
actually reachable, which we missed the first time.

Actually spin forever to be consistent with the comment and to make the
unreachable() annotation guaranteed to be unreachable.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

This fix alters the ordering of the IRQ and device registrations in the RTC
driver probe function. This change will apply to the RTC driver that supports
both DA9052 and DA9053 PMICs.

A problem could occur with the existing RTC driver if:

A system is started from a cold boot using the PMIC RTC IRQ to initiate a
power on operation. For instance, if an RTC alarm is used to start a
platform from power off.
The existing driver IRQ is requested before the device has been properly
registered.

i.e.
ret = da9052_request_irq()
comes before
rtc->rtc = devm_rtc_device_register();

In this case, an interrupt exists before the device has been registered and
the IRQ handler can be called immediately: this can happen be before the
memory for rtc->rtc has been allocated. The IRQ handler da9052_rtc_irq()
contains the function call:

rtc_update_irq(rtc->rtc, 1, RTC_IRQF | RTC_AF);

which in turn tries to access the unavailable rtc->rtc.

The fix is to reorder the functions inside the RTC probe. The IRQ is
requested after the RTC device resource has been registered so that
da9052_request_irq() is the last thing to happen.
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

If a previously-set alarm was disabled and then triggered, it may still
be pending when a new alarm is configured.

Then, if the alarm is enabled before the pending alarm is cleared, then
an interrupt is immediately raised.

Unfortunately, when the alarm is cleared and enabled during the same I²C
block write, the chip (at least the DS1339 I have) considers that the
alarm is enabled before it is cleared, and raises an interrupt.

This patch ensures that the pending alarm is cleared before the alarm is
enabled.
Signed-off-by: NNicolas Boullis <nboullis@debian.org>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The i2c_smbus_read_i2c_block_data function returns 0 on success, not the
number of bytes written.

Hence, when there are 32 bytes or less to send, the
ds1307_native_smbus_write_block_data function returns 0 on success,
while it returns the number of bytes when there are more than 32.

The ds1307_write_block_data always returns the number of bytes on
success.
Signed-off-by: NNicolas Boullis <nboullis@debian.org>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The valid range of day of week register for DS1302 is 1 to 7.  But the
set_time callback for rtc-ds1302 attempts to write the value of
tm->tm_wday which is in the range 0 to 6.  While the get_time callback
correctly decodes the register.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Sergey Yanovich <ynvich@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The set_time callback for rtc-ds1302 doesn't write clock registers
because the error check for the return value from spi_write_then_read()
is not correct.  spi_write_then_read() which returns zero on success.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Sergey Yanovich <ynvich@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Handle the Oscillator Failure (OF) bit on each read of date-time.
If the OF is set, an error is returned (-EINVAL) instead of the date-time.
The OF bit is cleared each time the date is set.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

To enable the wakealarm, the device must be able to wakeup.
This is done by setting the device wakeup capability to true with
'device_init_wakeup' function.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Previous 'commit c3b79770 ("Expire alarms after the time is set")'
and 'commit 48e97667 ("remove disabled alarm functionality")' removed
the alarm support because the alarm irq was not functional.

Add the alarm IRQ functionality with newer functions than previous
code. Tested with 'rtctest' and the alarm is functional.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Replace the obsolete "simple_strtoul" function to "kstrtoul".
Remove some checkpatch's errors, warnings and checks :
   - alignment with open parenthesis
   - spaces around '<' and '<<'
   - blank line after structure
   - quoted string split across lines
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Replace bit shifts by BIT macro.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The driver used i2c_transfer methods to read and set date/time.
The smbus methods should be used.

This commit replaces i2c_transfer functions by i2c_smbus_XX_i2c_block_data
for reading and setting the datetime.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Remove the CONFIG_RTC_INTF_PROC and CONFIG_RTC_INTF_PROC_MODULE macro
which is not necessary anymore.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The driver used an old sysfs entry export.
Update it to use the DEVICE_ATTR_XX macro and remove the unnecessary
CONFIG_RTC_INTF_SYSFS macro.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Many drivers are defining a DRV_VERSION. This is often only used for
MODULE_VERSION and sometimes to print an info message at probe time. This
is kind of pointless as they are all versionned with the kernel anyway.
Also the core will print a message when a new rtc is found.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

mr is written twice with the same value, remove one of the
redundant assignments to mr.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

DS1302 is an half-duplex SPI device. The driver respects this fact now.
Pin configurations should be implemented using SPI subsystem.
Signed-off-by: NSergei Ianovich <ynvich@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>