If you compile without OF_MDIO support in an RGMII configuration, we fail
to configure the dp83867 phy today by writing garbage into its configuration
registers.

On the other hand if you do compile with OF_MDIO and the phy gets loaded via
device tree, you have to have the properties set in the device tree, otherwise
we fail to load the driver and don't even attach the generic phy driver to
the interface anymore.

To make things slightly more consistent, make the rgmii configuration properties
optional and allow a user to omit them in their device tree.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_OF_MDIO is configured as module, the #define for it really
is CONFIG_OF_MDIO_MODULE, not CONFIG_OF_MDIO. So if we are compiling it
as module, the dp83867 doesn't see that OF_MDIO was selected and doesn't
read the dt rgmii parameters.

The fix is simple: Use IS_ENABLED(). It checks for both - module as well
as compiled in code.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The address of the device can be determined from the phydev structure,
rather than passing it as a parameter.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device tree properties for a phy device are expected to be in the phy
node. The current code for the DP83867 also tries to look in the
parent node. The devices binding documentation does not mention this,
no current device tree file makes use of this, and it is not behaviour
we want. So remove looking in the parent device.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/phy/dp83867.c:126:1-4: WARNING: end returns can be simpified
drivers/net/phy/dp83867.c:74:5-8: WARNING: end returns can be simpified if tested value is negative or 0

 Simplify a trivial if-return sequence.  Possibly combine with a
 preceding function call.

Generated by: scripts/coccinelle/misc/simple_return.cocci

CC: Dan Murphy <dmurphy@ti.com>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix warning: logical ‘or’ of collectively exhaustive tests is always true

Change the internal delay check from an 'or' condition to an 'and'
condition.
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the device tree entries to modify the '_' to '-'.
Also changes the names of the internal delay properties
from -int- to -internal- as the -int- appeared as a keyword.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the TI dp83867 Gigabit ethernet phy
device.

The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>