When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.

This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.

[ balbi@ti.com : added devicetree documentation, spelled threshold
		completely, made sure threshold is only applied to
		proper core revisions. ]
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch initializes platform data at pci glue layer, and SoCs x86-based
platform vendor is able to define their flags in platform data at bus glue
layer. Then do some independent behaviors at dwc3 core level.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some chip vendor is on pre-silicon phase, which needs to use the simulation
board. It should have the same product and vendor id with the true soc, but
might have some minor different configurations.

Below thread discussion proposes to find a method to distinguish between
simulation board and soc.

http://marc.info/?l=linux-usb&m=141194772206369&w=2

In Andvanced Configuration of coreConsultant, there is the parameter of
DWC_USB_EN_FPGA. This bit has the function we need. And it would response as 7
bit of GHWPARAMS6 register. So it's able to check this functional bit to confirm
if works on FPGA board.
Reported-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It enables hibernation if the function is set in coreConsultant.
Suggested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.

This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.

[1] http://markmail.org/message/x5zneg4xea4zntabAcked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some gadget/function drivers might want to do
improper request recycling by allocating a single
request from one particular endpoint and queueing
it to another completely unrelated endpoint.

One such case was found with f_loopback.c.

To prevent such cases from happening again, let's
WARN() so we get a loud enough failure and persuade
users to report errors.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

whenever we get a Disconnect Interrupt, we should
make sure to update out udc state to NOT_ATTACHED,
otherwise sysfs will show wrong values.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Using ->prepare()/->complete() to mask/unmask
IRQs is wrong at least for dwc3. We need to
make sure that by the end of ->resume(), IRQs
are working and ready to fire because a child
device may need working IRQs for its own ->resume()
method.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Enabling the core interrupts in complete is too late for
XHCI, and stops it from proper operation. The root of the
problem is due to a disagreement between dwc3-omap and XHCI
about when IRQs should be enabled.

As it turns out, ->resume's documentation states that:

"... generally the driver is expected to start working
again, responding to hardware events and software requests
(the device itself may be left in a low-power state, waiting
for a runtime resume to occur) ..."

From that we infer that IRQs must be unmasked by the end of
->resume().

Due to that, we will remove ->prepare() and ->complete() and
disable/enable interrupts in ->suspend()/->resume().
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add TRB tracepoints for ep0 TRBs as that
might help finding bugs with ep0 handling.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Adding ACPI ID used on newer Intel SoCs.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If the probe drivers have already set the dma_mask, not
replacing the value.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

tracing infrastructure already adds those for us.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

DWC3's GUID register is supposed to be used to write
any sort of version we might want. It helps when getting
bug reports for platforms you don't have HW to know
which kernel version of the driver was running on the
platform.

Because we don't really track driver version, but we _do_
track the kernel version, let's write LINUX_VERSION_CODE to
that register and use it for debugging.
Reviewed-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On ISOC endpoints the last trb_pool entry used as a
LINK TRB is not getting zeroed out correctly due to
memset being called incorrectly and in the wrong place.
If pool allocated from DMA was not zero-initialized
to begin with this will result in the size and ctrl
values being random garbage. Call memset correctly after
assignment of the trb_link pointer.

Fixes: f6bafc6a ("usb: dwc3: convert TRBs into bitshifts")
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: NJack Pham <jackp@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This reverts commit 02dae36a.

That commit is bogus in two ways:

1) There's no way dwc3-omap's ->suspend() can cause any effect
	on xhci's ->suspend(). Linux device driver model guarantees
	that a parent's ->suspend() will only be called after all
	children are suspended. dwc3-omap is the parent of the
	parent of xhci.

2) When implementing Deep Sleep states where context is lost,
	USBOTGSS_IRQ0 register, well, looses context so we
	_must_ rewrite it otherwise core IRQs will never be
	reenabled and USB will appear to be dead.

Fixes: 02dae36a (usb: dwc3: dwc3-omap: Disable/Enable only
	wrapper interrupts in prepare/complete)
Cc: <stable@vger.kernel.org> # v3.17
Cc: George Cherian <george.cherian@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

According to Section 8.5.3.2 of the USB 2.0 specification,
a USB device must terminate a Data Phase with either a
short packet or a ZLP (if the previous transfer was
a multiple of wMaxPacketSize).

For reference, here's what the USB 2.0 specification, section
8.5.3.2 says:

"
8.5.3.2 Variable-length Data Stage

A control pipe may have a variable-length data phase
in which the host requests more data than is contained
in the specified data structure. When all of the data
structure is returned to the host, the function should
indicate that the Data stage is ended by returning a
packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of
wMaxPacketSize for the pipe, the function will return
a zero-length packet to indicate the end of the Data
stage.
"
Signed-off-by: NFelipe Balbi <balbi@ti.com>

if our list of requests is empty, return early.

There's really nothing to be done in case our
request list is empty anyway because the only
situation where we our list is empty, is when
we're transferring ZLPs.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The device controller is the same but it has different PCI ID. Add this new
ID to the driver's list of supported IDs.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

According to our Gadget Framework API documentation,
->set_halt() *must* return -EAGAIN if we have pending
transfers (on either direction) or FIFO isn't empty (on
TX endpoints).

Fix this bug so that the mass storage gadget can be used
without stall=0 parameter.

This patch should be backported to all kernels since v3.2.

Cc: <stable@vger.kernel.org> # v3.2+
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Instead of releasing the lock and calling locked
versions of our set_halt() methods, let's hold
the lock all the way through and call unlocked
versions of those functions.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

__dwc3_gadget_ep_set_halt() is the function which
handles the actual halt feature. In order to cope
with some extra cleanup comming as a follow-up patch
let's move the isochronous endpoint check there too.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

dwc3_gadget_ep0_set_halt() will be called without
locks held in some cases, so we must hold the lock
on our own. While at that, also add a version without
locks to be called in certain conditions.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The way trace works is that it won't decode strings
until we read the actual trace. Because of that, we
can't make assumptions of pointers still being valid
at the time we read the trace. In order to avoid that,
just copy all fields from every struct pointer we need
for our traces.

Ths patch fixes the following bug:

[ 2940.039229] Unable to handle kernel paging request at virtual address 814efa9e
[ 2940.046904] pgd = ec3dc000
[ 2940.049737] [814efa9e] *pgd=00000000
[ 2940.053552] Internal error: Oops: 5 [#1] SMP ARM
[ 2940.058379] Modules linked in: usb_f_acm u_serial g_serial usb_f_uac2 libcomposite configfs xhci_hcd dwc3 udc_core matrix_keypad dwc3_omap lis3lv02d_i2c lis3lv02d input_polldev [last unloaded: g_audio]
[ 2940.077238] CPU: 0 PID: 3020 Comm: tail Tainted: G        W
3.17.0-rc5-dirty #1097
[ 2940.085596] task: ed1b1040 ti: ed07c000 task.ti: ed07c000
[ 2940.091258] PC is at strnlen+0x18/0x68
[ 2940.095177] LR is at 0xfffffffe
[ 2940.098454] pc : [<c0356df8>]    lr : [<fffffffe>]    psr: a0000013
[ 2940.098454] sp : ed07ddb0  ip : ed07ddc0  fp : ed07ddbc
[ 2940.110445] r10: c070ff70  r9 : ed07de70  r8 : 00000000
[ 2940.115906] r7 : 814efa9e  r6 : ffffffff  r5 : ed4b6087  r4 : ed4b50c7
[ 2940.122726] r3 : 00000000  r2 : 814efa9e  r1 : ffffffff  r0 : 814efa9e
[ 2940.129546] Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM Segment user
[ 2940.137000] Control: 10c5387d  Table: ac3dc059  DAC: 00000015
[ 2940.143006] Process tail (pid: 3020, stack limit = 0xed07c248)
[ 2940.149098] Stack: (0xed07ddb0 to 0xed07e000)
[ 2940.153660] dda0:                                     ed07dde4 ed07ddc0 c0359628 c0356dec
[ 2940.162203] ddc0: 00000000 ed4b50c7 bf03ae9c ed4b6087 bf03ae9e 00000002 ed07de3c ed07dde8
[ 2940.170740] dde0: c035ab50 c0359600 ffffffff ffffffff ff0a0000 ffffffff ed07de30 ed4b5088
[ 2940.179275] de00: ed4b50c7 00000fc0 ff0a0004 ffffffff ed4b5088 ed4b5088 00000000 00001000
[ 2940.187810] de20: 00001008 00000fc0 ed4b5088 00000000 ed07de68 ed07de40 c00f1e64 c035a9c4
[ 2940.196341] de40: bf03dae0 ed07de70 ed4b4000 ec25b280 ed4b4000 ec25b280 bf03dae0 ed07de9c
[ 2940.204886] de60: ed07de78 bf033324 c00f1e0c bf03ae9c 814efa9e ed428bc0 814eca3e 00000000
[ 2940.213428] de80: 814eba3e ed4b4000 03bd1201 c0c34790 ed07ded4 ed07dea0 c00edc0c bf0332d0
[ 2940.221994] dea0: 000002c7 ed07df10 ed07decc ed07deb8 ed4b4000 0000209c ec278ac0 00000000
[ 2940.230536] dec0: 00002000 ec0db340 ed07def4 ed07ded8 c00ee7ec c00eda90 c00ee7b0 ec278ac0
[ 2940.239075] dee0: ed4b4000 000002d5 ed07df44 ed07def8 c018b8d0 c00ee7bc c0166d3c ec278af0
[ 2940.247621] df00: 0001f090 ed07df78 000002c7 00000000 000002c8 00000000 00000000 ec0db340
[ 2940.256173] df20: 0001f090 ed07df78 ec0db340 00002000 0001f090 00000000 ed07df74 ed07df48
[ 2940.264729] df40: c0166e98 c018b5f4 00000001 c018535c 000168c1 00000000 ec0db340 ec0db340
[ 2940.273284] df60: 00002000 0001f090 ed07dfa4 ed07df78 c01675c4 c0166e0c 000168c1 00000000
[ 2940.281829] df80: 00002000 0000000a 0001f090 00000003 c000f064 ed07c000 00000000 ed07dfa8
[ 2940.290365] dfa0: c000ede0 c0167584 00002000 0000000a 00000003 0001f090 00002000 00000000
[ 2940.298909] dfc0: 00002000 0000000a 0001f090 00000003 7fffe000 0001e1e0 00002004 0000002f
[ 2940.307445] dfe0: 00000000 beed38ec 000104c8 b6e6397c 40000010 00000003 00000000 00000000
[ 2940.315992] [<c0356df8>] (strnlen) from [<c0359628>] (string.isra.8+0x34/0xe8)
[ 2940.323534] [<c0359628>] (string.isra.8) from [<c035ab50>] (vsnprintf+0x198/0x3fc)
[ 2940.331461] [<c035ab50>] (vsnprintf) from [<c00f1e64>] (trace_seq_printf+0x68/0x94)
[ 2940.339494] [<c00f1e64>] (trace_seq_printf) from [<bf033324>] (ftrace_raw_output_dwc3_log_request+0x60/0x78 [dwc3])
[ 2940.350424] [<bf033324>] (ftrace_raw_output_dwc3_log_request [dwc3]) from [<c00edc0c>] (print_trace_line+0x188/0x418)
[ 2940.361507] [<c00edc0c>] (print_trace_line) from [<c00ee7ec>] (s_show+0x3c/0x12c)
[ 2940.369330] [<c00ee7ec>] (s_show) from [<c018b8d0>] (seq_read+0x2e8/0x4a0)
[ 2940.376519] [<c018b8d0>] (seq_read) from [<c0166e98>] (vfs_read+0x98/0x158)
[ 2940.383796] [<c0166e98>] (vfs_read) from [<c01675c4>] (SyS_read+0x4c/0xa0)
[ 2940.390981] [<c01675c4>] (SyS_read) from [<c000ede0>] (ret_fast_syscall+0x0/0x48)
[ 2940.398792] Code: e24cb004 e3510000 e241e001 0a000011 (e5d01000)
[ 2940.406980] ---[ end trace d8b38370fbb531f3 ]---
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There is no need to init .owner field.

Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"

This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: NKiran Padwal <kiran.padwal@smartplayin.com>
Reviewed-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.

All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: NMichal Sojka <sojka@merica.cz>
Acked-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

DWC3 glue layer is hardware layer around Synopsys DesignWare
USB3 core. Its purpose is to supply Synopsys IP with required
clocks, voltages and interface it with the rest of the SoC.
Signed-off-by: NIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It manages the powerdown signal,
and configures the internal glue logic and syscfg registers.

[ balbi@ti.com : actually switch over to of_platform_depopulate() ]
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When we're debugging hard-to-reproduce and time-sensitive
use cases, printk() poses too much overhead. That's when
the kernel's tracing infrastructure comes into play.

This patch implements a few initial tracepoints for the
dwc3 driver. More traces can be added as necessary in order
to ease the task of debugging dwc3.
Reviewed-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

No functional changes, just making sure we're dealing
with unsigned ints.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this new helper will return a pretty string for
DWC3 Gadget Events.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Those functions are only using within debugging
messages, grouping them into debug.h makes sense.

While at that, also add missing multiple inclusion
guard.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

After commit 2ec2a8be (usb: dwc3: gadget:
always enable IOC on bulk/interrupt transfers)
we created a situation where it was possible to
hang a bulk/interrupt endpoint if we had more
than one pending request in our queue and they
were both started with a single Start Transfer
command.

The problems triggers because we had not enabled
Transfer In Progress event for those endpoints
and we were not able to process early giveback
of requests completed without LST bit set.

Fix the problem by finally enabling Xfer In Progress
event for all endpoint types, except control.

Fixes: 2ec2a8be (usb: dwc3: gadget: always
	enable IOC on bulk/interrupt transfers)
Cc: <stable@vger.kernel.org> # v3.14+
Reported-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we don't to gate clocks until our children are
done with their remove path.

Fixes: af310e96 (usb: dwc3: omap: use runtime API's to enable clocks)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We can't suspend the PHYs before dwc3_core_exit_mode()
has been called, that's because the host and/or device
sides might still need to communicate with the far end
link partner.

Fixes: 8ba007a9 (usb: dwc3: core: enable the USB2 and USB3 phy in probe)
Cc: <stable@vger.kernel.org> # v3.9+
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Currently, we disable pm_runtime before all register
accesses are done, this is dangerous and might lead
to abort exceptions due to the driver trying to access
a register which is clocked by a clock which was long
gated.

Fix that by moving pm_runtime_put_sync() and pm_runtime_disable()
as the last thing we do before returning from our ->remove()
method.

Fixes: 72246da4 (usb: Introduce DesignWare USB3 DRD Driver)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: NFelipe Balbi <balbi@ti.com>

dep->endpoint.desc is checked at the beginning of
dwc3_gadget_ep_queue(), but after that it may be set to NULL
by another thread and then accessed again in dwc3_gadget_ep_queue().
This will lead to kernel oops.

Expand spinlock protection area to aviod race condition.
Signed-off-by: NZhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: NJiebing Li <jiebing.li@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>