Drop code which was relevant when there were chips with
3 antennas. Setting to ANT_AB should be ok with all mvm
supported chips.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

No use of the ieee80211 header. Drop it.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Introduce rs_rate which represents a rate. Use this structure
instead of iwl_scale_tbl_info where we're dealing with a single
rate.
This avoids allocating the big iwl_scale_tbl_info structure
on the stack in several cases like converting to ucode rate
format or from ucode rate format.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove this as it's unused.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remain in the same Tx modulation (i.e. column) for a longer
time before starting a search cycle for a better modulation.
This has been shown to give better results.
Also change the name of the timeout define to better match its
description.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Rename for clearer names.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Expected TPT table was updated only when switching to a new
modulation. This is wrong as toggling aggregation changes
the expected TPT signficantly.
This leads to scenarios where turning aggregation on after
being in MIMO sends us back to SISO despite a perfect success
ratio.
This occurred because the TPT of the SISO mode was being
estimated based on aggregation while the MIMO one wasn't.

Also remove an error print which isn't an error anymore
since we might be updating the expected TPT table due
to aggregation changes.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This terminates a test window of a new rate quicker in case
we've hit a bad rate and should recover better.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enable better tracking of different decisions made
by the rate scale algorithm.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remote peer can publish a different number of supported nss via the
operating mode notification IE or action frame. If it limits to 1
then we don't want mimo rates configured in the rate table.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

MCS9 in NSS=1 or NSS=2 isn't valid for 20Mhz so don't enable
it in case we're dealing with a 20Mhz sta. Trying to configure an
MCS9 rate with 20Mhz in the LQ rate table would lead to a FW assert.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Switch to using the new btcoex decision api regarding MIMO and stop
accessing the internal btcoex structs.
In case MIMO should be disabled it would detect this upon the next
Tx and force a search. The search will switch to SISO on a antenna A
which isn't used by BT.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add more bit field definitions used in LQ flags.
Also rename the first bit to a shorter name.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Re-initialize rs when we get a rate_update hook called which
happens when remote STA changes bandwidth or sends a VHT opmode
notification.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Refactor setting of VHT enabled rates in preparation of adding
some more logic there.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove the flags parameter which should be set to sync or async
according to whether this is called during sta init or not.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Info about VHT/HT rates wasn't printed properly when dumping
the rate scale table. Fix that and print more info. While at it
fix some other minor issues in the printing and prevent
overflowing the print buffer.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove code that is not needed and always allow MIMO when
in tight mode. In loose mode, we should avoid MIMO since BT
can use the other antenna to Rx while we Tx.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The code limiting the AMPDU length due to BT traffic was
duplicated. Remove the redundant code.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Tests have shown that we should start AMPDU even when BT
is active. So remove that constraint.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In loose BT Coex scheme, the aggregation size doesn't need to
be limited.

To avoid triggering it, remove a lockdep assertion - we need
to compute the AMPDU size limit from rate control code which
can't take mvm->mutex. This means that there is a race but in
the worst case, we will have a wrong AMPDU size limit which
is not a big issue.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mvm doesn't support HT GF so drop all relevant code in rs.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Enable rs algorithm to use VHT rates and use 80Mhz.
This enables reaching VHT rates which wasn't possible.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The data in MailBox comes direclty from the BT core.
We should use the data processed by the WiFi fw that is
appended to the MailBox in the BT Coex notification.
Also decide on whether the Coex type based on the input
from the the firmware and not hard coded.

Also fix the SMPS SISO threshold to 2 (it was 3).
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

VHT introduces MCS8 and MCS9. Update the expected tpt tables
to include these. Previous expected values for 20/40 MHz
are incorrect in certain cases so fix these as well.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Tested-by: NEfi Tubul <efi.tubul@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Current code didn't handle well the case where we're in SISO using
ANT B and there's a BT load. Switch to ANT A in this case.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The XXX_SWITCH_ANTENNA1/2 actions keep track of switching between
3 single antennas or between 3 pairs in case of MIMO2 on a MIMO3 device.
As current and future chips will have at most 2 antennas drop these.
While at it also convert the actions into enums and cleanup
the code a bit.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

clean it up
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Current and future chips supported by mvm will only have a maximum
of 2 antennas so all the MIMO3 related code and states can be dropped.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

rs_get_tbl_info_from_mcs() mistakenly clears
the rate histories window, overriding its initialization
values (i.e. filling it with 0, instead of -1).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some more cleanups of unused fields and their initializations.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This isn't very informative and can be deduced from rate_scale_table.
Remove as a preparation for dropping iwl_rs_rate_info.ieee.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

rs_ht_to_legacy and ant_toggle_lookup are arrays that
represent some state-machine. initialize them explicitly
with designated initialization to make them more clear
and avoid errors.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The traffic load monitoring isn't used anymore to decide whether
a Tx aggregation on a specific TID should be started.
No point in collecting these statistics. Remove the relevant code.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The rate scale windows are cleared twice as part of the init.
Cleanup this duplication in both mvm and dvm.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The LQ command argument isn't needed, it's always taken from the
station struct that's already passed, remove the argument.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

5 and 10 MHz support needs to know the current operating channel width,
add the chandef to the rate control API.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

If someone wants to disable AMPDU, there is the 11n_disable
module parameter.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since driver does not use control.rates[0].count, we have never set that
variable. But currently, after rate control API rewrite, this is required
by mac80211. Otherwise legacy rates control does not work and we transmit
always at 1Mbit/s on pre 11n networks.

[same fix as for iwlegacy, thanks Stanislaw!]
Signed-off-by: NMoshe Benji <Moshe.Benji@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Another step in the rate control / BT Coex integration
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>