Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2017-06-06

This series contains fixes to i40e and i40evf only.

Mauro S. M. Rodrigues fixes a flood in the kernel log which was introduced
in a previous commit because of a mistaken substitution of __I40E_VSI_DOWN
instead of __I40E_DOWN when testing the state of the PF.

Björn Töpel fixes an issue introduced in a previous commit where the
offset was incorrect and could lead to data corruption for architectures
using PAGE_SIZE larger than 8191.  Fixed the issue by updating the
page_offset correctly using the proper setting for truesize.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit b699d003.

As per Eric Dumazet, the pskb_may_pull() is a NOP in this
particular case, so the 'iph' reload is unnecessary.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In f8b45b74 ("i40e/i40evf: Use build_skb to build frames")
i40e_build_skb updates the page_offset field with an incorrect offset,
which can lead to data corruption. This patch updates page_offset
correctly, by properly setting truesize.

Note that the bug only appears on architectures where PAGE_SIZE is
8192 or larger.

Fixes: f8b45b74 ("i40e/i40evf: Use build_skb to build frames")
Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 0da36b97 ("i40e: use DECLARE_BITMAP for state fields")
introduced changes in the way i40e works with state flags converting
them to bitmaps using kernel bitmap API. This change introduced a
regression due to a mistaken substitution using __I40E_VSI_DOWN instead
of __I40E_DOWN when testing state of a PF at i40e_reset_subtask()
function. This caused a flood in the kernel log with the follow message:

[49.013] i40e 0002:01:00.0: bad reset request 0x00000020

Commit d19cb64b ("i40e: separate PF and VSI state flags")
also introduced some misuse of the VSI and PF flags, so both could be
considered as the offenders.

This patch simply fixes the flags where it makes sense by changing
__I40E_VSI_DOWN to __I40E_DOWN.

Fixes: 0da36b97 ("i40e: use DECLARE_BITMAP for state fields")
Fixes: d19cb64b ("i40e: separate PF and VSI state flags")
Reviewed-by: N"Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: N"Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Granular QoS per VF feature must be enabled in FW before it can be
used.

Thus, the driver cannot modify a QP's qos_vport value (via the UPDATE_QP FW
command) if the feature has not been enabled -- the FW returns an error if
this is attempted.

Fixes: 08068cd5 ("net/mlx4: Added qos_vport QP configuration in VST mode")
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix kernel-doc warnings (typo) in drivers/net/phy/phy.c:

..//drivers/net/phy/phy.c:259: warning: No description found for parameter 'features'
..//drivers/net/phy/phy.c:259: warning: Excess function parameter 'feature' description in 'phy_lookup_setting'
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We must free allocated skb when genlmsg_put() return fails.

Fixes: 1555d204 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update tcp.txt to fix mandatory congestion control ops and default
CCA selection. Also, fix comment in tcp.h for undo_cwnd.
Signed-off-by: NAnmol Sarma <me@anmolsarma.in>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our previous patch (cited below) introduced a regression
for RAW Eth QPs.

Fix it by checking if the QP number provided by user-space
exists, hence allowing steering rules to be added for valid
QPs only.

Fixes: 89c55768 ("net/mlx4_en: Avoid adding steering rules with invalid ring")
Reported-by: NOr Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: NTalat Batheesh <talatb@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since iptunnel_pull_header() can call pskb_may_pull(),
we must reload any pointer that was related to skb->head.

Fixes: a09a4c8d ("tunnels: Remove encapsulation offloads on decap")
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexander reported various KASAN messages triggered in recent kernels

The problem is that ping sockets should not use udp_poll() in the first
place, and recent changes in UDP stack finally exposed this old bug.

Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind")
Fixes: 6d0bfe22 ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NSasha Levin <alexander.levin@verizon.com>
Cc: Solar Designer <solar@openwall.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Acked-By: NLorenzo Colitti <lorenzo@google.com>
Tested-By: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 9520ed8f ("net: dsa: use cpu_switch instead of ds[0]")
replaced the use of dst->ds[0] with dst->cpu_switch since that is
functionally equivalent, however, we can now run into an use after free
scenario after unbinding then rebinding the switch driver.

The use after free happens because we do correctly initialize
dst->cpu_switch the first time we probe in dsa_cpu_parse(), then we
unbind the driver: dsa_dst_unapply() is called, and we rebind again.
dst->cpu_switch now points to a freed "ds" structure, and so when we
finally dereference it in dsa_cpu_port_ethtool_setup(), we oops.

To fix this, simply set dst->cpu_switch to NULL in dsa_dst_unapply()
which guarantees that we always correctly re-assign dst->cpu_switch in
dsa_cpu_parse().

Fixes: 9520ed8f ("net: dsa: use cpu_switch instead of ds[0]")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If ip6_find_1stfragopt() fails and we return an error we have to free
up 'segs' because nobody else is going to.

Fixes: 2423496a ("ipv6: Prevent overrun when parsing v6 header options")
Reported-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 9b4437a5 ("geneve: Unify LWT and netdev handling.")
when using COLLECT_METADATA geneve devices are created with too small of
a needed_headroom and too large of a max_mtu. This is because
ip_tunnel_info_af() is not valid with the device level info when using
COLLECT_METADATA and we mistakenly fall into the IPv4 case.

For COLLECT_METADATA, always use the worst case of ipv6 since both
sockets are created.

Fixes: 9b4437a5 ("geneve: Unify LWT and netdev handling.")
Signed-off-by: NEric Garver <e@erig.me>
Acked-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prior to f5f99309 (sock: do not set sk_err in
sock_dequeue_err_skb), sk_err was reset to the error of
the skb on the head of the error queue.

Applications, most notably ping, are relying on this
behavior to reset sk_err for ICMP packets.

Set sk_err to the ICMP error when there is an ICMP packet
at the head of the error queue.

Fixes: f5f99309 (sock: do not set sk_err in sock_dequeue_err_skb)
Reported-by: NCyril Hrubis <chrubis@suse.cz>
Tested-by: NCyril Hrubis <chrubis@suse.cz>
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

xgbe_map_rx_buffer is rather confused about what PAGE_ALLOC_COSTLY_ORDER
means. It uses PAGE_ALLOC_COSTLY_ORDER-1 assuming that
PAGE_ALLOC_COSTLY_ORDER is the first costly order which is not the case
actually because orders larger than that are costly. And even that
applies only to sleeping allocations which is not the case here. We
simply do not perform any costly operations like reclaim or compaction
for those. Simplify the code by dropping the order calculation and use
PAGE_ALLOC_COSTLY_ORDER directly.
Signed-off-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip6_route_output() requires that the flowlabel contains the traffic
class for policy routing.

Commit 0e9a7095 ("ip6_tunnel, ip6_gre: fix setting of DSCP on
encapsulated packets") removed the code which previously added the
traffic class to the flowlabel.

The traffic class is added here because only route lookup needs the
flowlabel to contain the traffic class.

Fixes: 0e9a7095 ("ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets")
Signed-off-by: NLiam McBirnie <liam.mcbirnie@boeing.com>
Acked-by: NPeter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use software polling (PHY_POLL) to check for link state changes instead
of relying on the EMAC's hardware polling feature.  Some PHY drivers
are unable to get a functioning link because the HW polling is not
robust enough.

The EMAC is able to poll the PHY on the MDIO bus looking for link state
changes (via the Link Status bit in the Status Register at address 0x1).
When the link state changes, the EMAC triggers an interrupt and tells the
driver what the new state is.  The feature eliminates the need for
software to poll the MDIO bus.

Unfortunately, this feature is incompatible with phylib, because it
ignores everything that the PHY core and PHY drivers are trying to do.
In particular:

1. It assumes a compatible register set, so PHYs with different registers
   may not work.

2. It doesn't allow for hardware errata that have work-arounds implemented
   in the PHY driver.

3. It doesn't support multiple register pages. If the PHY core switches
   the register set to another page, the EMAC won't know the page has
   changed and will still attempt to read the same PHY register.

4. It only checks the copper side of the link, not the SGMII side.  Some
   PHY drivers (e.g. at803x) may also check the SGMII side, and
   report the link as not ready during autonegotiation if the SGMII link
   is still down.  Phylib then waits for another interrupt to query
   the PHY again, but the EMAC won't send another interrupt because it
   thinks the link is up.

Cc: stable@vger.kernel.org # 4.11.x
Tested-by: NManoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit d85b758f ("virtio_net: fix support for small rings")
was supposed to increase the buffer size for small rings but had an
unintentional side effect of decreasing it for large rings. This seems
to break some setups - it's not yet clear why, but increasing buffer
size back to what it was before helps.

Fixes: d85b758f ("virtio_net: fix support for small rings")
Reported-by: NMikulas Patocka <mpatocka@redhat.com>
Reported-by: N"J. Bruce Fields" <bfields@fieldses.org>
Tested-by: NMikulas Patocka <mpatocka@redhat.com>
Tested-by: N"J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Qlogic's 82xx series adapter doesn't support
tunnel offloads, driver incorrectly assumes that it is
supported and causes firmware hang while running tunnel IO.

This patch fixes this by not advertising tunnel offloads
for 82xx adapters.
Signed-off-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding a vxlan interface to a socket isn't symmetrical, while adding
is done in vxlan_open() the deletion is done in vxlan_dellink().
This can cause a use-after-free error when we close the vxlan
interface before deleting it.

We add vxlan_vs_del_dev() to match vxlan_vs_add_dev() and call
it from vxlan_stop() to match the call from vxlan_open().

Fixes: 56ef9c90 ("vxlan: Move socket initialization to within rtnl scope")
Acked-by: NJiri Benc <jbenc@redhat.com>
Tested-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NMark Bloch <markb@mellanox.com>
Acked-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original author left the project and so far has not
responded to emails sent to the listed address.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix NETDEV WATCHDOG timeout on startup by adding missing register
writes that properly setup SGMII.
Signed-off-by: NThor Thayer <thor.thayer@linux.intel.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the sender switches its congestion control during loss
recovery, if the recovery is spurious then it may incorrectly
revert cwnd and ssthresh to the older values set by a previous
congestion control. Consider a congestion control (like BBR)
that does not use ssthresh and keeps it infinite: the connection
may incorrectly revert cwnd to an infinite value when switching
from BBR to another congestion control.

This patch fixes it by disallowing such cwnd undo operation
upon switching congestion control.  Note that undo_marker
is not reset s.t. the packets that were incorrectly marked
lost would be corrected. We only avoid undoing the cwnd in
tcp_undo_cwnd_reduction().
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NSoheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Take uld mutex to avoid race between cxgb_up() and
cxgb4_register_uld() to enable napi for the same uld
queue.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

xfrm6_find_1stfragopt() may now return an error code and we must
not treat it as a length.

Fixes: 2423496a ("ipv6: Prevent overrun when parsing v6 header options")
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Acked-by: NCraig Gallek <kraig@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2017-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just two fixes:
 * fix the per-CPU drop counters to not be added to the
   rx_packets counter, but really the drop counter
 * fix TX aggregation start/stop callback races by setting
   bits instead of allocating and queueing an skb
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dsa_switch_suspend() and dsa_switch_resume() are functions that belong in
net/dsa/dsa.c and are not part of the legacy platform support code.

Fixes: a6a71f19 ("net: dsa: isolate legacy code")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On SYSTEMPORT Lite, since we have the main interrupt source in the first
cell, the second cell is the Wake-on-LAN interrupt, yet the code was not
properly updated to fetch the second cell, and instead looked at the
third and non-existing cell for Wake-on-LAN.

Fixes: 44a4524c ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the commit enabling per-CPU station statistics, I inadvertedly
copy-pasted some code to update rx_packets and forgot to change it
to update rx_dropped_misc. Fix that.

This addresses https://bugzilla.kernel.org/show_bug.cgi?id=195953.

Fixes: c9c5962b ("mac80211: enable collecting station statistics per-CPU")
Reported-by: NPetru-Florin Mihancea <petrum@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Leonard Crestez says:

====================
ARM: imx6ul-14x14-evk: Fix suspend over nfs by phy

Right now attempting doing suspend/resume while root is mounted over NFS
hangs on imx6ul-14x14-evk. This is happening because ksz8081 phy fixups are
lost on resume.

Fix this by using equivalent devicetree properties instead of a phy fixup
and handling those properties on resume in the micrel driver.

In theory it might now be possible to remove the phy fixup from mach-imx6ul
entirely but it is possible that this would break other imx6ul boards which
use the same phy. The solution would be to patch their dts but it's not
clear how to identify affected boards.

This code is shared with imx6ull-14x14-evk but 6ull suspend needs an
unrelated patch: https://lkml.org/lkml/2017/5/30/584

This is something of a corner case so there is no CC: stable.

Changes since v1: https://lkml.org/lkml/2017/5/30/672
 * Split a kszphy_config_reset function for stuff shared between
config_init and resume. Calling config_init directly could be an option but
on some HW variants it does extra stuff like parsing devicetree options.
That would not be appropriate for resume code.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These bits seem to be lost after a suspend/resume cycle so just set them
again. Do this by splitting the handling of these bits into a function
that is also called on resume.

This patch fixes ethernet suspend/resume on imx6ul-14x14-evk boards.
Signed-off-by: NLeonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right now mach-imx6ul registers a fixup for the ksz8081 phy. The same
register values can be set through the micrel phy driver by using dts
properties.

This seems preferable and allows cleanly fixing suspend/resume.
Signed-off-by: NLeonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver may sleep under a read spin lock, and the function call path is:
send_socklist (acquire the lock by read_lock)
  skb_copy(GFP_KERNEL) --> may sleep

To fix it, the "GFP_KERNEL" is replaced with "GFP_ATOMIC".
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 0c1d70af ("net: use dst_cache for vxlan device"),
cached dst entries could be leaked when more than one remote was
present for a given vxlan_fdb entry, causing subsequent netns
operations to block indefinitely and "unregister_netdevice: waiting
for lo to become free." messages to appear in the kernel log.

Fix by properly releasing cached dst and freeing resources in this
case.

Fixes: 0c1d70af ("net: use dst_cache for vxlan device")
Signed-off-by: NLance Richardson <lrichard@redhat.com>
Acked-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the transition of NO_STP -> KERNEL_STP was fixed by always calling
mod_timer in br_stp_start, it introduced a new regression which causes
the timer to be armed even when the bridge is down, and since we stop
the timers in its ndo_stop() function, they never get disabled if the
device is destroyed before it's upped.

To reproduce:
$ while :; do ip l add br0 type bridge hello_time 100; brctl stp br0 on;
ip l del br0; done;

CC: Xin Long <lucien.xin@gmail.com>
CC: Ivan Vecera <cera@cera.cz>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reported-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Fixes: 6d18c732 ("bridge: start hello_timer when enabling KERNEL_STP in br_stp_start")
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Apparently multi-cos isn't working for bnx2x quite some time -
driver implements ndo_select_queue() to allow queue-selection
for FCoE, but the regular L2 flow would cause it to modulo the
fallback's result by the number of queues.
The fallback would return a queue matching the needed tc
[via __skb_tx_hash()], but since the modulo is by the number of TSS
queues where number of TCs is not accounted, transmission would always
be done by a queue configured into using TC0.

Fixes: ada7c19e ("bnx2x: use XPS if possible for bnx2x_select_queue instead of pure hash")
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change t4fw_version.h to update latest firmware version
number to 1.16.45.0.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NETLINK_F_LISTEN_ALL_NSID otion enables to listen all netns that have a
nsid assigned into the netns where the netlink socket is opened.
The nsid is sent as metadata to userland, but the existence of this nsid is
checked only for netns that are different from the socket netns. Thus, if
no nsid is assigned to the socket netns, NETNSA_NSID_NOT_ASSIGNED is
reported to the userland. This value is confusing and useless.
After this patch, only valid nsid are sent to userland.
Reported-by: NFlavio Leitner <fbl@sysclose.org>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver may sleep under a write spin lock, and the function
call path is:
qlcnic_82xx_hw_write_wx_2M (acquire the lock by write_lock_irqsave)
  crb_win_lock
    qlcnic_pcie_sem_lock
      usleep_range
qlcnic_82xx_hw_read_wx_2M (acquire the lock by write_lock_irqsave)
  crb_win_lock
    qlcnic_pcie_sem_lock
      usleep_range

To fix it, the usleep_range is replaced with udelay.
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>