Atm, we apply this workaround somewhat inconsistently at the following
points: driver loading, LVDS init, eDP PPS init, system resume. As this
workaround also affects registers other than PPS (timing, PLL) a more
consistent way is to apply it early after the PPS HW context is known to
be lost: driver loading, system resume and on VLV/CHV/BXT when turning
on power domains.

This is needed by the next patch that removes saving/restoring of the
PP_CONTROL register.

This also removes the incorrect programming of the workaround on HSW+
PCH platforms which don't have the register locking mechanism.

v2: (Ville)
- Don't apply the workaround on BXT.
- Simplify platform checks using HAS_DDI().
v3:
- Move the call of intel_pps_unlock_regs_wa() to the more
  logical vlv_display_power_well_init() (also fixing CHV) (Ville).
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-5-git-send-email-imre.deak@intel.com

Similarly to the previous patch, initialize the PPS from the DP
encoder's resume hook. Note that as opposed to LVDS we can't do this
during encoder enabling, since we need the PPS for DP detection as well.
The PPS init code is now the same for init and resume, so factor out a
new intel_dp_pps_init() helper for this.

v2:
- Factor out intel_dp_pps_init() (Ville).
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-4-git-send-email-imre.deak@intel.com

Atm the LVDS encoder depends on the PPS HW context being saved/restored
from generic suspend/resume code. Since the PPS is specific to the LVDS
and eDP encoders a cleaner way is to reinitialize it during encoder
enabling, so do this here for LVDS. Follow-up patches will init the PPS
for the eDP encoder similarly and remove the suspend/resume time save /
restore.

v2:
- Apply BSpec +1 offset and use DIV_ROUND_UP() when programming the
power cycle delay. (Ville)
v3: (Ville)
- Fix +1 vs. round-up order.
- s/reset_on_powerdown/powerdown_on_reset/
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-3-git-send-email-imre.deak@intel.com

These two flags mean the same thing, so remove the duplication.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-2-git-send-email-imre.deak@intel.com

The PPS registers are pretty much the same everywhere, the differences
being:
- Register fields appearing, disappearing from one platform to the
  next: panel-reset-on-powerdown, backlight-on, panel-port,
  register-unlock
- Different register base addresses
- Different number of PPS instances: 2 on VLV/CHV/BXT, 1 everywhere
  else.

We can merge the separate set of PPS definitions by extending the PPS
instance argument to all platforms and using instance 0 on platforms
with a single instance. This means we'll need to calculate the register
addresses dynamically based on the given platform and PPS instance.

v2:
- Simplify if ladder in intel_pps_get_registers(). (Ville)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-1-git-send-email-imre.deak@intel.com

As we're tweaking the GuC-related code in debugfs, we can
drop the no-longer-used 'q_fail' and repack the structure.
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

Now that host structures are indexed by host engine-id rather than
guc_id, we can usefully convert some for_each_engine() loops to use
for_each_engine_id() and avoid multiple dereferences of engine->id.

Also a few related tweaks to cache structure members locally wherever
they're used more than once or twice, hopefully eliminating memory
references.
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

The Context Descriptor passed by the kernel to the GuC contains a field
specifying which engine(s) the context will use. Historically, this was
always set to "all of them", but if we had a separate client for each
engine, we could be more precise, and set only the bit for the engine
that the client was associated with. So this patch enables this usage,
in preparation for having multiple clients, though at this point there
is still only a single client used for all supported engines.
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

We have essentially the same code in each of two different
loops, so we can refactor it into a little helper function.

This also reduces the amount of work done during startup,
as we now only reprogram h/w found to be in a state other
than that expected, and so avoid the overhead of setting
doorbell registers to the state they're already in.
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

guc_init_doorbell_hw() borrows the (currently single) GuC client to use
in reinitialising ALL the doorbell registers (as the hardware doesn't
reset them when the GuC is reset). As a prerequisite for accommodating
multiple clients, it should only reset doorbells that are supposed to be
disabled, avoiding those that are marked as in use by any client.
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

The bottom-half we use for processing the breadcrumb interrupt is a
task, which is an RCU protected struct. When accessing this struct, we
need to be holding the RCU read lock to prevent it disappearing beneath
us. We can use the RCU annotation to mark our irq_seqno_bh pointer as
being under RCU guard and then use the RCU accessors to both provide
correct ordering of access through the pointer.

Most notably, this fixes the access from hard irq context to use the RCU
read lock, which both Daniel and Tvrtko complained about.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470761272-1245-3-git-send-email-chris@chris-wilson.co.uk

In commit 2529d570 ("drm/i915: Drop racy markup of missed-irqs from
idle-worker") the racy detection of missed interrupts was removed when
we went idle. This however opened up the issue that the stuck waiters
were not being reported, causing a test case failure. If we move the
stuck waiter detection out of hangcheck and into the breadcrumb
mechanims (i.e. the waiter) itself, we can avoid this issue entirely.
This leaves hangcheck looking for a stuck GPU (inspecting for request
advancement and HEAD motion), and breadcrumbs looking for a stuck
waiter - hopefully make both easier to understand by their segregation.

v2: Reduce the error message as we now run independently of hangcheck,
and the hanging batch used by igt also counts as a stuck waiter causing
extra warnings in dmesg.
v3: Move the breadcrumb's hangcheck kickstart to the first missed wait.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97104
Fixes: 2529d570 (waiter"drm/i915: Drop racy markup of missed-irqs...")
Testcase: igt/drv_missed_irq
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470761272-1245-2-git-send-email-chris@chris-wilson.co.uk

One of the few guarantees we want the busy ioctl to provide is that the
reported busy writer is included in the set of busy read engines. This
should be provided by the ordering of setting and retiring the active
trackers, but we can do better by explicitly setting the busy read
engine flag for the last writer.

v2: More comments inside __busy_write_id() to explain why both fields
are set.

Fixes: 3fdc13c7 ("drm/i915: Remove (struct_mutex) locking for busy-ioctl")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470762505-12799-1-git-send-email-chris@chris-wilson.co.ukReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Recent versions of gcc say this:

include/drm/i915_drm.h:96:34: warning: result of ‘65535 << 20’
requires 37 bits to represent, but ‘int’ only has 32 bits
[-Wshift-overflow=]
Reported-by: NDavid Binderman <linuxdev.baldrick@gmail.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470764110-23855-1-git-send-email-david.s.gordon@intel.com

I mistyped and added an extra _request_ to __i915_gem_active_get_rcu()
Also, the same happened to another comment for i915_gem_active_get_rcu()
Reported-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470758602-1338-1-git-send-email-chris@chris-wilson.co.uk

We don't have GPU reset support for gen2, which means the display
hardware is unaffected when a GPU hang is handled. However as the ring
has in fact stopped, any flips still in the ring will never complete,
and thus the display base address updates will never happen. So we
really need to fix that up manually just like we do on g4x+.

In fact, let's just use intel_has_gpu_reset() instead of IS_GEN2()
since that'll also handle cases where someone would disable the GPU
reset support on gen3/4 for whatever reason.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470428910-12125-5-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Factor out the "does the GPU reset clobber the display?" check into a
small helper.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470428910-12125-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add force_reset_modeset_test as a parameter to force the modeset path during gpu reset.
This allows a IGT test to set the knob and trigger a hang to force the gpu reset,
even on platforms that wouldn't otherwise require it.

Changes since v1:
- Split out fix to separate commit.
Changes since v2:
- This commit is purely about force_reset_modeset_test now.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Testcase: drv_hangman.reset-with-forced-modeset
Tested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470428910-12125-3-git-send-email-ville.syrjala@linux.intel.comSigned-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

This function would call drm_modeset_lock_all, while the suspend/resume
functions already have their own locking. Fix this by factoring out
__intel_display_resume, and calling the atomic helpers for duplicating
atomic state and disabling all crtc's during suspend.

Changes since v1:
- Deal with -EDEADLK right after lock_all and clean up calls
  to hw readout.
- Always take all modeset locks so updates during gpu reset are blocked.
Changes since v2:
- Fix deadlock in intel_update_primary_planes.
- Move WARN_ON(EDEADLK) to __intel_display_resume.
- pctx -> ctx
- only call __intel_display_resume on success in intel_display_resume.
Changes since v3:
- Rebase on top of dev_priv -> dev change.
- Use drm_modeset_lock_all_ctx instead of drm_modeset_lock_all.
Changes since v4 [by vsyrjala]:
- Deal with skip_intermediate_wm
- Update comment w.r.t. mode_config.mutex vs. ->detect()
- Rebase due to INTEL_GEN() etc.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: e2c8b870 ("drm/i915: Use atomic helpers for suspend, v2.")
Cc: stable@vger.kernel.org
Tested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470428910-12125-2-git-send-email-ville.syrjala@linux.intel.com

Marking PCH transcoder FIFO underrun reporting as disabled for
transcoder B/C on LPT-H will block us from enabling the south error
interrupt. So let's only mark transcoder A underrun reporting as
disabled initially.

This is a little tricky to hit since you need a machine with LPT-H, and
the BIOS must enable either pipe B or C at boot. Then i915 would mark
the "transcoder B/C" underrun reporting as disabled and never enable it
again, meaning south interrupts would never get enabled either. The only
other interrupt in there is actually the poison interrupt which, if we
could ever trigger it, would just result in a little error in dmesg.

Here's the resulting change in SDEIMR on my HSW when I boot it with
multiple displays attached:
- (0x000c4004): 0xf115ffff
+ (0x000c4004): 0xf114ffff

My previous attempt [1] tried to fix this a little differently, but
Daniel requested I do this instead.

[1] https://lists.freedesktop.org/archives/intel-gfx/2015-November/081420.html

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470416417-15021-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_enable_pipe() looks rather confusing when one side doesn't have
the curly braces, and the other one does. And what's even worse,
there's another if-else inside the braceless side. Let's put braces
around it to make it clear which branch goes where.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470418894-1249-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

When using RCU lookup for the request, commit 0eafec6d ("drm/i915:
Enable lockless lookup of request tracking via RCU"), we acknowledge that
we may race with another thread that could have reallocated the request.
In order for the first thread not to blow up, the second thread must not
clear the request completed before overwriting it. In the RCU lookup, we
allow for the engine/seqno to be replaced but we do not allow for it to
be zeroed.

The choice we make is to either add extra checking to the RCU lookup, or
embrace the inherent races (as intended). It is more complicated as we
need to manually clear everything we depend upon being zero initialised,
but we benefit from not emiting the memset() to clear the entire
frequently allocated structure (that memset turns up in throughput
profiles). And at the same time, the lookup remains flexible for future
adjustments.

v2: Old style LRC requires another variable to be initialize. (The
danger inherent in not zeroing everything.)
v3: request->batch also needs to be cleared
v4: signaling.tsk is no long used unset, but pid still exists

Fixes: 0eafec6d ("drm/i915: Enable lockless lookup of request...")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: "Goel, Akash" <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470731014-6894-2-git-send-email-chris@chris-wilson.co.uk

In the debate as to whether the second read of active->request is
ordered after the dependent reads of the first read of active->request,
just give in and throw a smp_rmb() in there so that ordering of loads is
assured.

v2: Explain the manual smp_rmb()
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470731014-6894-1-git-send-email-chris@chris-wilson.co.uk

When we force the cleanup after a GPU hang, we want to retire all
requests, or else we may leak them if truly wedged (and the GPU never
advances again). Converting to the active request helpers had the issue
of doing the check against busyness before reporting the request, so if
we claim the GPU had hung but this engine hadn't we could potential skip
the request cleanup - triggering the self-check BUG.

Fixes: dcff85c8 ("drm/i915: Enable i915_gem_wait_for_idle() ...")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470728222-10243-3-git-send-email-chris@chris-wilson.co.uk

As we do the lockdep protected RCU lookup in a couple of places,
refactor that code to a common helper i915_gem_active_raw().
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470728222-10243-2-git-send-email-chris@chris-wilson.co.uk

This was originally introduced to be used by the busy-ioctl, but in the
end busy ioctl performed a different dance. Since there are no users,
and no likely users, remove an unwanted chunk of the API.
Suggested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470728222-10243-1-git-send-email-chris@chris-wilson.co.ukReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In i915_ggtt_cleanup_hw we need to remember to free aliasing_ppgtt. This
fixes the following kmemleak message:

unreferenced object 0xffff880213cca000 (size 8192):
  comm "modprobe", pid 1298, jiffies 4294745402 (age 703.930s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff817c808e>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff8121f9c2>] kmem_cache_alloc_trace+0x142/0x1d0
    [<ffffffffa06d11ef>] i915_gem_init_ggtt+0x10f/0x210 [i915]
    [<ffffffffa06d71bb>] i915_gem_init+0x5b/0xd0 [i915]
    [<ffffffffa069749a>] i915_driver_load+0x97a/0x1460 [i915]
    [<ffffffffa06a26ef>] i915_pci_probe+0x4f/0x70 [i915]
    [<ffffffff81423015>] local_pci_probe+0x45/0xa0
    [<ffffffff81424463>] pci_device_probe+0x103/0x150
    [<ffffffff81515e6c>] driver_probe_device+0x22c/0x440
    [<ffffffff81516151>] __driver_attach+0xd1/0xf0
    [<ffffffff8151379c>] bus_for_each_dev+0x6c/0xc0
    [<ffffffff8151555e>] driver_attach+0x1e/0x20
    [<ffffffff81514fa3>] bus_add_driver+0x1c3/0x280
    [<ffffffff81516aa0>] driver_register+0x60/0xe0
    [<ffffffff8142297c>] __pci_register_driver+0x4c/0x50
    [<ffffffffa013605b>] 0xffffffffa013605b
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Fixes: b18b6bde ("drm/i915/bdw: Free PPGTT struct")
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470420280-21417-1-git-send-email-matthew.auld@intel.com

~jiffie and a few usecs is 3 orders of magnitude different. A bit
much. This was changed in

commit ca5b721e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Fri Dec 11 11:32:58 2015 +0000

    drm/i915: Limit the busy wait on requests to 5us not 10ms!

But probably missed the comment since the change was non-local to the
comment.

v2: Polish comment more (Chris).

Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470413484-23775-1-git-send-email-daniel.vetter@ffwll.ch

No functional change. Instead of defining a new empty function
let's use what is available on drm.

It gets cleaner, and easy to read, and understand.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Copy to user return the number of bytes it couldn't write
and zero on success. So any number different than 0 should
be considered a fault, not only when it doesn't write
the full size.

v2: fixed the inverted logic. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

This reverts commit f64425a8.

active_streams will get totally out of whack with SST unless we
sync up with the hw state at readout, obviously! We don't yet
do that, so now the WARNs fire all the time. Let's revert :(
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470413142-26402-1-git-send-email-ville.syrjala@linux.intel.com
References: https://bugs.freedesktop.org/show_bug.cgi?id=95472#c14Acked-by: NChris Wilson <chris@chris-wilson.co.uk>

As pointed out by Chris Harris, we are using the wrong WA name, it
should in fact be WaToEnableHwFixForPushConstHWBug, also it should be
applied from C0 onwards for both BXT and KBL.

Fixes: 7b9005cd ("drm/i915: Add WaInsertDummyPushConstP for bxt and kbl")

Cc: Chris Harris <chris.harris@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reported-by: NChris Harris <chris.harris@intel.com>
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Reviewed-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470127013-29653-1-git-send-email-matthew.auld@intel.com

With all callers now not playing tricks with dropping the struct_mutex
between waiting and retiring, we can assert that the request is ready to
be retired.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-19-git-send-email-chris@chris-wilson.co.uk

In the previous commit, we moved the obj->tiling_mode out of a bitfield
and into its own integer so that we could safely use READ_ONCE(). Let us
now repair some of that damage by sharing the tiling_mode with its
companion, the fence stride.

v2: New magic
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-18-git-send-email-chris@chris-wilson.co.uk

Through the GTT interface to the fence registers, we can only handle
linear, X and Y tiling. The more esoteric tiling patterns are ignored.
Document that the tiling ABI only supports upto Y tiling, and reject any
attempts to set a tiling mode other than NONE, X or Y.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-17-git-send-email-chris@chris-wilson.co.uk

Since we are not concerned with userspace racing itself with set-tiling
(the order is indeterminant even if we take a lock), then we can safely
read back the single obj->tiling_mode and do the static lookup of
swizzle mode without having to take a lock.

get-tiling is reasonably frequent due to the back-channel passing around
of tiling parameters in DRI2/DRI3.

v2: Make tiling_mode a full unsigned int so that we can trivially use it
with READ_ONCE(). Separating it out into manual control over the flags
field was too noisy for a simple patch. Note that we could use the lower
bits of obj->stride for the tiling mode.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-16-git-send-email-chris@chris-wilson.co.uk

We don't need to incur the overhead of checking whether the object is
pinned prior to changing its madvise. If the object is pinned, the
madvise will not take effect until it is unpinned and so we cannot free
the pages being pointed at by hardware. Marking a pinned object with
allocated pages as DONTNEED will not trigger any undue warnings. The check
is therefore superfluous, and by removing it we can remove a linear walk
over all the vma the object has.

Still despite it being an overzealous check, that error code is part of
the current ABI and so we must proceed with caution.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-15-git-send-email-chris@chris-wilson.co.uk

We only need to take the struct_mutex if the object is pinned to the
display engine and so requires checking for clflush. (The race with
userspace pinning the object to a framebuffer is irrelevant.)

v2: Use access once for compiler hints (or not as it is a bitfield)
v3: READ_ONCE, obj->pin_display is not a bitfield anymore
v4: Don't be creative with goto.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-14-git-send-email-chris@chris-wilson.co.uk

By applying the same logic as for wait-ioctl, we can query whether a
request has completed without holding struct_mutex. The biggest impact
system-wide is removing the flush_active and the contention that causes.

Testcase: igt/gem_busy
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470388464-28458-13-git-send-email-chris@chris-wilson.co.uk