GPIO3_29 is used to reset the ethernet phy.

Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

GPIO1_25 is used to reset the ethernet phy.

Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

MX6QDL_PAD_EIM_D23__GPIO3_IO23 pin is used to reset the ethernet phy.

Add it to the 'hog' group.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add pcie device node for imx6qdl.
Signed-off-by: NSean Cross <xobs@kosagi.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

For more information about the Udoo board:
http://www.udoo.org/Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add pinmux for 4-bit SD card connected to SSP2.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add initial PHYTEC VF610 Cosmic/Cosmic+ board support with
UART and FEC enabled.
Signed-off-by: NMatt Porter <matt.porter@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This pin definition had been added after the initial patch to use
symbolic pin names in DTS files.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Update the Ka-Ro TX28 DTS file.

- add Copyright header
- use label references for better readability
- sort the entries alphabetically
- add some aliases used by U-Boot to modify the DT data
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

For some reason, the select input of pin function USB_OTG_ID is not
implemented via a regular select input register but using the bit
USB_OTG_ID_ SEL (shift 13) of IOMUXC_GPR1 register (offset 0x4).

As per the workaround for such quirk implemented in pinctrl driver,
we need to compose the input_val cell as below.

	31     23      15      7        0
	| 0xff | shift | width | select |

Thus, we have 0xff0d0100 for MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID and
0xff0d0101 for MX6QDL_PAD_GPIO_1__USB_OTG_ID in input_val cell.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NPeter Chen <peter.chen@freescale.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Convert mx23/mx28 dts files to use the padconfig defintions from
mxs-pinfunc.h.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Convert mx23/mx28 dts filed to use the pinctrl header files.

NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts

According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX

I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Remove the list of possible pin configurations from the documentation
file and create header files containing those definitions.
This eliminates the need for error-prone manual lookup of those values
in the documentation and guarantees consistency between the human
readable representation of the pad function in the .dts file and the
actual binary value used in DT.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Provide 'lradc-touchscreen-wires' property to the LRADC driver, so that
touchscreen can be functional.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

On imx6qdl-sabresd the SDHC2 and SDHC3 are 8 bit-wide, so pass the bus-width
property to reflect that.

Otherwise the mmc driver will operate with the default bus-width value of 4.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This is needed for supporting ultra high speed cards like SD3.0 cards.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add spi aliases.

While at it, keep the aliases entries sorted.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Enable USB function for OTG 1 and OTG 2 at mx6sololite evk.
Besides, fix the wrong interrupt number for OTG2 and host 1.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add iomuxc gpr device node for imx6sl.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch enables DSPI0 and at26df081a flash device for Vybrid VF610
TOWER board.
Signed-off-by: NChao Fu <b44548@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add Freescale DSPI node into vf610 dts.
Signed-off-by: NChao Fu <b44548@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

imx6q-sabrelite board can be connected to a 1024x768 Hannstar LVDS panel.

Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Put the nodes in alphabetical order so that further node additions can be better
organized.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Trying to use the usb otg port on mx53qsb results in the following error:

$ modprobe g_ether
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 52:0f:8a:1e:aa:09
usb0: MAC de:f3:70:d8:6c:62
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready

(Connect the USB cable)

$ ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11

USB otg port goes to connector J3 (mini USB) and also to the USB combo (J2).

As mx53qsb does not provide a USB ID pin, pass the dr_mode as 'peripheral' so
that we can have usb device working.

Tested via g_ether.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Testing g_ether results in the following:

[    1.648022] using random self ethernet address
[    1.652778] using random host ethernet address
[    1.660504] usb0: HOST MAC c6:28:6a:81:dc:ff
[    1.666360] usb0: MAC 7e:81:54:16:c0:c6
[    1.670504] using random self ethernet address
[    1.675842] using random host ethernet address
[    1.682655] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[    1.689332] g_ether gadget: g_ether ready
[    3.328974] irq 237: nobody cared (try booting with the "irqpoll" option)
[    3.335831] CPU: 0 PID: 1 Comm: swapper Not tainted 3.11.0-rc6-next-20130819 #1035
[    3.343500] [<c0014258>] (unwind_backtrace+0x0/0xf0) from [<c0011b20>] (show_stack+0x10/0x14)
[    3.352098] [<c0011b20>] (show_stack+0x10/0x14) from [<c006af4c>] (__report_bad_irq+0x20/0xc0)
[    3.360763] [<c006af4c>] (__report_bad_irq+0x20/0xc0) from [<c006b3f4>] (note_interrupt+0x1d4/0x234)
[    3.369943] [<c006b3f4>] (note_interrupt+0x1d4/0x234) from [<c0069754>] (handle_irq_event_percpu+0xc4/0x268)
[    3.379815] [<c0069754>] (handle_irq_event_percpu+0xc4/0x268) from [<c0069934>] (handle_irq_event+0x3c/0x5c)
[    3.389686] [<c0069934>] (handle_irq_event+0x3c/0x5c) from [<c006bb78>] (handle_level_irq+0x8c/0xe8)
[    3.398865] [<c006bb78>] (handle_level_irq+0x8c/0xe8) from [<c0068ff0>] (generic_handle_irq+0x20/0x30)
[    3.408213] [<c0068ff0>] (generic_handle_irq+0x20/0x30) from [<c000fc9c>] (handle_IRQ+0x30/0x84)
[    3.417040] [<c000fc9c>] (handle_IRQ+0x30/0x84) from [<c0012564>] (__irq_svc+0x44/0x54)
[    3.425094] [<c0012564>] (__irq_svc+0x44/0x54) from [<c0020244>] (__do_softirq+0x90/0x268)
[    3.433400] [<c0020244>] (__do_softirq+0x90/0x268) from [<c00207d4>] (irq_exit+0x9c/0xd8)
[    3.441619] [<c00207d4>] (irq_exit+0x9c/0xd8) from [<c000fca0>] (handle_IRQ+0x34/0x84)
[    3.449577] [<c000fca0>] (handle_IRQ+0x34/0x84) from [<c0012564>] (__irq_svc+0x44/0x54)
[    3.457629] [<c0012564>] (__irq_svc+0x44/0x54) from [<c04602b0>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[    3.467164] [<c04602b0>] (_raw_spin_unlock_irqrestore+0x34/0x44) from [<c0348298>] (input_register_handler+0x98/0xb4)
[    3.477835] [<c0348298>] (input_register_handler+0x98/0xb4) from [<c064bc10>] (mousedev_init+0x30/0x60)
[    3.487275] [<c064bc10>] (mousedev_init+0x30/0x60) from [<c00088ac>] (do_one_initcall+0xe8/0x154)
[    3.496198] [<c00088ac>] (do_one_initcall+0xe8/0x154) from [<c062aabc>] (kernel_init_freeable+0xf0/0x1b4)
[    3.505810] [<c062aabc>] (kernel_init_freeable+0xf0/0x1b4) from [<c0456550>] (kernel_init+0x8/0xe4)
[    3.514899] [<c0456550>] (kernel_init+0x8/0xe4) from [<c000ee60>] (ret_from_fork+0x14/0x34)
[    3.523263] handlers:
[    3.525578] [<c0339d14>] ci_irq
[    3.528757] Disabling IRQ #237

Provide the USB0_ID pin in the usb0 node, so that g_ether can operate
correctly.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Tested via g_ether:

$ modprobe g_ether
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 42:b5:26:a9:48:21
usb0: MAC 36:a6:85:9b:9e:13
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
$ g_ether gadget: high-speed config #1: CDC Ethernet (ECM)
$ ifconfig usb0 10.0.0.2

Then on the PC host side:

~$ sudo ifconfig usb0 10.0.0.1
~$ ping 10.0.0.2
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
64 bytes from 10.0.0.2: icmp_req=1 ttl=64 time=1.26 ms
64 bytes from 10.0.0.2: icmp_req=2 ttl=64 time=0.280 ms
64 bytes from 10.0.0.2: icmp_req=3 ttl=64 time=0.297 ms
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds the missing W1 (onewire) devicetree node for i.MX51 CPUs.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This patch adds the missing IRAM devicetree node for i.MX51 CPUs.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

RTS/CTS pins can be used for different purposes, so create separate
definitions for these pins.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

There is no imx6sl specific sdma firmware.  Instead, imx6sl reuses
imx6q sdma firmware.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add pinmux configuration for MCBSP2 connected to the TDM interface.
With this configuration the Headset modules works as expected.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Commit 76787b3b (ARM: OMAP2+: Remove board-4430sdp.c)
removed legacy booting in favor of device tree based booting
for 4430sdp. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.

I don't have the "1283 PG 2.21 connectivity device" on my 4430sdp,
but the earlier version of this patch was tested by Luciano
Coelho. This version has left out the input logic for MMC CLK
line compared to the earlier version as that is not bidirectional,
and should be safe to do.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Cc: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Commit b42b9181 (ARM: OMAP2+: Remove board-omap4panda.c)
removed legacy booting in favor of device tree based booting
for pandaboard. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.

The legacy muxing was setting pulls for GPIO 48 and 49, so let's
keep that behaviour for now to avoid further regressions for
BT and FM. Also input logic was enabled for MMC CLK line, but
I've verified that the input logic we don't need enabled for
CLK line as it's not bidirectional.

Also, we want to use non-removable instead of ti,non-removable
as the ti,non-removable also sets no_regulator_off_init which
is really not what we want as then wl12xx won't get powered
up and down which is needed for resetting it.

Note that looks like the WLAN interface fails to come up after
a warm reset, but that most likely was also happening with
the legacy booting and needs a separate fix.

Cc: Paolo Pisati <p.pisati@gmail.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Fix the DTS data for ocp2scp node by adding the
missing reg property.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

USB3 block has a 64KiB space, another 64KiB is
used for the wrapper.

Without this change, resource_size() will get
confused and driver won't probe because size
will be negative.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The BeagleBone Black is basically a regular BeagleBone with eMMC and
HDMI added, so create a common dtsi both can use.

IMPORTANT: booting the existing am335x-bone.dts will blow up the HDMI
transceiver after a dozen boots with an uSD card inserted because LDO
will be at 3.3V instead of 1.8.

MMC support for AM335x still isn't in, so only the LDO change has been
added.
Signed-off-by: NKoen Kooi <koen@dominion.thruhere.net>
Tested-by: NTom Rini <trini@ti.com>
Tested-by: NMatt Porter <matt.porter@linaro.org>
Acked-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The beagle and beagle-xm entries were inside the same double quote.
Split them to have two distinct entries.
Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The patch "0b7a76aa ARM: dts: imx6q{dl}: add DTE pads for uart"
adds the DTE pads for uart. For PAD_EIM_D29, the offset of the
Pad Mux register should be 0x0c8, not 0x0c4.

This patch fixes it.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Commit 718a3500 (ARM: i.MX51: Add PATA support) adds pata support to the
imx51.dtsi file and is using clock 161. The problem is that the right
clock is 172, according to commit 5d530bb0 (ARM: i.MX5: Add PATA and SRTC
clocks).  Using the clock 172 makes things work again (and kills a nasty
system freeze).
Tested-by: NSteev Klimaszewski <steev@gentoo.org>
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>