* drm-fbdev-cleanup:
  drm/fb: remove drm_fb_helper_setcolreg
  drm/kms/fb: use slow work mechanism for normal hotplug also.
  drm/kms/fb: add polling support for when nothing is connected.
  drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
  drm/kms/fb: separate fbdev connector list from core drm connectors
  drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
  drm/fb: fix fbdev object model + cleanup properly.

Conflicts:
	drivers/gpu/drm/i915/i915_drv.h
	drivers/gpu/drm/nouveau/nouveau_drv.h

* drm-radeon-lockup:
  drm/radeon/kms: simplify & improve GPU reset V2
  drm/radeon/kms: rename gpu_reset to asic_reset
  drm/radeon/kms: fence cleanup + more reliable GPU lockup detection V4

Conflicts:
	drivers/gpu/drm/radeon/r300.c

* drm-edid-fixes:
  drm/edid: When checking duplicate standard modes, walked the probed list
  drm/edid: Fix sync polarity for secondary GTF curve
  drm/modes: Fix interlaced mode names
  drm/edid: Add secondary GTF curve support
  drm/edid: Strengthen the algorithm for standard mode codes
  drm/edid: Fix the HDTV hack.
  drm/edid: Extend range-based mode addition for EDID 1.4
  drm/edid: Add test for monitor reduced blanking support.
  drm/edid: Fix preferred mode parse for EDID 1.4
  drm/edid: Remove some silly comments
  drm/edid: Remove arbitrary EDID extension limit
  drm/edid: Add modes for Established Timings III section
  drm/edid: Reshuffle mode list construction to closer match the spec
  drm/edid: Remove a redundant check
  drm/edid: Remove some misleading comments
  drm/edid: Fix secondary block fetch.

* drm-ttm-pool:
  drm/ttm: using kmalloc/kfree requires including slab.h
  drm/ttm: include linux/seq_file.h for seq_printf
  drm/ttm: Add sysfs interface to control pool allocator.
  drm/ttm: Use set_pages_array_wc instead of set_memory_wc.
  arch/x86: Add array variants for setting memory to wc caching.
  drm/nouveau: Add ttm page pool debugfs file.
  drm/radeon/kms: Add ttm page pool debugfs file.
  drm/ttm: Add debugfs output entry to pool allocator.
  drm/ttm: add pool wc/uc page allocator V3

* 'anholt/drm-intel-next' of /home/airlied/kernel/drm-next: (48 commits)
  agp/intel-gtt: kill previous_size assignments
  agp/intel-gtt: kill intel_i830_tlbflush
  agp/intel: split out gmch/gtt probe, part 1
  agp/intel: kill mutli_gmch_chip
  agp/intel: uncoditionally reconfigure driver on resume
  agp/intel: split out the GTT support
  agp/intel: introduce intel-agp.h header file
  drm/i915: Don't touch PORT_HOTPLUG_EN in intel_dp_detect()
  drm/i915/pch: Use minimal number of FDI lanes (v2)
  drm/i915: Add the support of memory self-refresh on Ironlake
  drm/i915: Move Pineview CxSR and watermark code into update_wm hook.
  drm/i915: Only save/restore FBC on the platform that supports FBC
  drm/i915: Fix the incorrect argument for SDVO SET_TV_format command
  drm/i915: Add support of SDVO on Ibexpeak PCH
  drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on).
  drm/i915: do not read uninitialized ->dev_private
  Revert "drm/i915: Use a dmi quirk to skip a broken SDVO TV output."
  drm/i915: implement multifunction SDVO device support
  drm/i915: remove unused intel_pipe_get_connector()
  drm/i915: remove connector object in old output structure
  ...

The recent anon_vma fixes cause many anonymous pages to end up
in the parent process anon_vma, even when the page is exclusively
owned by the current process.

Adding exclusively owned anonymous pages to the top anon_vma
reduces rmap scanning overhead, especially in workloads with
forking servers.

This patch adds a parameter to __page_set_anon_rmap that can
be used to indicate whether or not the added page is exclusively
owned by the current process.

Pages added through page_add_new_anon_rmap are exclusively
owned by the current process, and can be added to the top
anon_vma.

Pages added through page_add_anon_rmap can be either shared
or exclusively owned, so we do the conservative thing and
add it to the oldest anon_vma.

A next step would be to add the exclusive parameter to
page_add_anon_rmap, to be used from functions where we do
know for sure whether a page is exclusively owned.
Signed-off-by: NRik van Riel <riel@redhat.com>
Reviewed-by: NJohannes Weiner <hannes@cmpxchg.org>
Lightly-tested-by: NBorislav Petkov <bp@alien8.de>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
[ Edited to look nicer  - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
  eCryptfs: Turn lower lookup error messages into debug messages
  eCryptfs: Copy lower directory inode times and size on link
  ecryptfs: fix use with tmpfs by removing d_drop from ecryptfs_destroy_inode
  ecryptfs: fix error code for missing xattrs in lower fs
  eCryptfs: Decrypt symlink target for stat size
  eCryptfs: Strip metadata in xattr flag in encrypted view
  eCryptfs: Clear buffer before reading in metadata xattr
  eCryptfs: Rename ecryptfs_crypt_stat.num_header_bytes_at_front
  eCryptfs: Fix metadata in xattr feature regression

Vaugue warnings about ENAMETOOLONG errors when looking up an encrypted
file name have caused many users to become concerned about their data.
Since this is a rather harmless condition, I'm moving this warning to
only be printed when the ecryptfs_verbosity module param is 1.
Signed-off-by: NTyler Hicks <tyhicks@linux.vnet.ibm.com>

The timestamps and size of a lower inode involved in a link() call was
being copied to the upper parent inode.  Instead, we should be
copying lower parent inode's timestamps and size to the upper parent
inode.  I discovered this bug using the POSIX test suite at Tuxera.
Signed-off-by: NTyler Hicks <tyhicks@linux.vnet.ibm.com>

Since tmpfs has no persistent storage, it pins all its dentries in memory
so they have d_count=1 when other file systems would have d_count=0.
->lookup is only used to create new dentries. If the caller doesn't
instantiate it, it's freed immediately at dput(). ->readdir reads
directly from the dcache and depends on the dentries being hashed.

When an ecryptfs mount is mounted, it associates the lower file and dentry
with the ecryptfs files as they're accessed. When it's umounted and
destroys all the in-memory ecryptfs inodes, it fput's the lower_files and
d_drop's the lower_dentries. Commit 4981e081 added this and a d_delete in
2008 and several months later commit caeeeecf removed the d_delete. I
believe the d_drop() needs to be removed as well.

The d_drop effectively hides any file that has been accessed via ecryptfs
from the underlying tmpfs since it depends on it being hashed for it to
be accessible. I've removed the d_drop on my development node and see no
ill effects with basic testing on both tmpfs and persistent storage.

As a side effect, after ecryptfs d_drops the dentries on tmpfs, tmpfs
BUGs on umount. This is due to the dentries being unhashed.
tmpfs->kill_sb is kill_litter_super which calls d_genocide to drop
the reference pinning the dentry. It skips unhashed and negative dentries,
but shrink_dcache_for_umount_subtree doesn't. Since those dentries
still have an elevated d_count, we get a BUG().

This patch removes the d_drop call and fixes both issues.

This issue was reported at:
https://bugzilla.novell.com/show_bug.cgi?id=567887Reported-by: NÁrpád Bíró <biroa@demasz.hu>
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Cc: Dustin Kirkland <kirkland@canonical.com>
Cc: stable@kernel.org
Signed-off-by: NTyler Hicks <tyhicks@linux.vnet.ibm.com>

If the lower file system driver has extended attributes disabled,
ecryptfs' own access functions return -ENOSYS instead of -EOPNOTSUPP.
This breaks execution of programs in the ecryptfs mount, since the
kernel expects the latter error when checking for security
capabilities in xattrs.
Signed-off-by: NChristian Pulvermacher <pulvermacher@gmx.de>
Cc: stable@kernel.org
Signed-off-by: NTyler Hicks <tyhicks@linux.vnet.ibm.com>

Create a getattr handler for eCryptfs symlinks that is capable of
reading the lower target and decrypting its path.  Prior to this patch,
a stat's st_size field would represent the strlen of the encrypted path,
while readlink() would return the strlen of the decrypted path.  This
could lead to confusion in some userspace applications, since the two
values should be equal.

https://bugs.launchpad.net/bugs/524919Reported-by: NLoïc Minier <loic.minier@canonical.com>
Cc: stable@kernel.org
Signed-off-by: NTyler Hicks <tyhicks@linux.vnet.ibm.com>

Commit b91ecb00 ("gigaset: include cleanup cleanup") removed an implicit
sched.h inclusion that came in via slab.h, and caused various compile
problems as a result.

This should fix it.
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  rcu: Make RCU lockdep check the lockdep_recursion variable
  rcu: Update docs for rcu_access_pointer and rcu_dereference_protected
  rcu: Better explain the condition parameter of rcu_dereference_check()
  rcu: Add rcu_access_pointer and rcu_dereference_protected

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  gigaset: include cleanup cleanup
  packet : remove init_net restriction
  WAN: flush tx_queue in hdlc_ppp to prevent panic on rmmod hw_driver.
  ip: Fix ip_dev_loopback_xmit()
  net: dev_pick_tx() fix
  fib: suppress lockdep-RCU false positive in FIB trie.
  tun: orphan an skb on tx
  forcedeth: fix tx limit2 flag check
  iwlwifi: work around bogus active chains detection

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: add FireMV 2400 PCI ID.
  drm/radeon/kms: allow R500 regs VAP_ALT_NUM_VERTICES and VAP_INDEX_OFFSET
  drivers/gpu/radeon: Add MSPOS regs to safe list.
  drm/radeon/kms: disable the tv encoder when tv/cv is not in use
  drm/radeon/kms: adjust pll settings for tv
  drm/radeon/kms: fix tv dac conflict resolver
  drm/radeon/kms/evergreen: don't enable hdmi audio stuff
  drm/radeon/kms/atom: fix dual-link DVI on DCE3.2/4.0
  drm/radeon/kms: fix rs600 tlb flush
  drm/radeon/kms: print GPU family and device id when loading
  drm/radeon/kms: fix calculation of mipmapped 3D texture sizes
  drm/radeon/kms: only change mode when coherent value changes.
  drm/radeon/kms: more atom parser fixes (v2)

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 5974/1: arm/mach-at91 Makefile: remove two blanks.
  ARM: 6052/1: kdump: make kexec work in interrupt context
  ARM: 6051/1: VFP: preserve the HW context when calling signal handlers
  ARM: 6050/1: VFP: fix the SMP versions of vfp_{sync,flush}_hwstate
  ARM: 6007/1: fix highmem with VIPT cache and DMA
  ARM: 5975/1: AT91 slow-clock suspend: don't wait when turning PLLs off

This is an M24/X600 chip.

From RH# 581927

cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

The lockdep facility temporarily disables lockdep checking by
incrementing the current->lockdep_recursion variable.  Such
disabling happens in NMIs and in other situations where lockdep
might expect to recurse on itself.

This patch therefore checks current->lockdep_recursion, disabling RCU
lockdep splats when this variable is non-zero.  In addition, this patch
removes the "likely()", as suggested by Lai Jiangshan.
Reported-by: NFrederic Weisbecker <fweisbec@gmail.com>
Reported-by: NDavid Miller <davem@davemloft.net>
Tested-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
Cc: eric.dumazet@gmail.com
LKML-Reference: <20100415195039.GA22623@linux.vnet.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

[airlied: fix V_A_N_V to not be safe and fix check to make sure only r500
 - bump userspace version]
Signed-off-by: NMarek Olšák <maraeo@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Permits MSAA and D3D-style rasterization.

[airlied: add rs600]
Signed-off-by: NCorbin Simpson <MostAwesomeDude@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Switching between TV and VGA caused VGA to break on some systems
since the TV encoder was left enabled when VGA was used.

fixes fdo bug 25520.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

May fix fdo bug 26582.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

On systems with the tv dac shared between DVI and TV,
we can only use the dac for one of the connectors.
However, when using a digital monitor on the DVI port,
you can use the dac for the TV connector just fine.
Check the use_digital status when resolving the conflict.

Fixes fdo bug 27649, possibly others.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Got broken during the evergreen merge.
Fixes fdo bug 27001.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Typo in in flush leaded to no flush of the RS600 tlb which
ultimately leaded to massive system ram corruption, with
this patch everythings seems to work properly.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This will help figuring out GPU when looking at bugs log.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Not needed for the GTT and inconsistent: Sometimes the _new_ size
was stored there ...
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

We don't use the generic insert/remove_memory functions that
require this. So kill this useless code.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

This is essentially the last piece of code that's tying intel-gtt.c
to intel-agp.c. Extract the probe code into it's own function so that
it can be moved to intel-gtt.c.

This requires some slight changes in the ordering of device probe function.
This patch just implements that for better bisectability in case this
introduces bugs.

The biggest change is that the gmch/gtt code doesn't execute a pci
resource fixup anymore. I've dug around in historical git trees, and
this change is to support the agp port on an old HP server with the
i440 intel chipset. So only needed for the agp driver.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

Always zero, i.e. unused.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

Only two drivers were not in this table (7505 and g33), both non-mobile
chipsets. So they were most likely just missing. This is another step
to untangle the gtt from the agp driver.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

intel-agp.c contains actually two different drivers: An agp driver
for _physical_ agp slots an the gtt driver that is used by the intel
drm modules. Split them to prevent any further confusion.

This patch just moves the code and includes intel-gtt.c in intel-agp.c
Later patches will untangle these two drivers further.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

Intel definitions have spilled into agp.h. Create a header file for
them and also include it in efficion-agp.c 'cause it needs a few of
them.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEric Anholt <eric@anholt.net>

PORT_HOTPLUG_EN has allready been setup in i915_driver_irq_postinstall(),
when intel_dp_detect() runs.

Delete the DP[BCD]_HOTPLUG_INT_EN defines, they are not referenced anymore.

I found this while searching for a fix for
        https://bugzilla.redhat.com/show_bug.cgi?id=528312Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: NEric Anholt <eric@anholt.net>

This should be a small power savings. Tested on Lenovo T410 (Ironlake), LVDS
VGA and DisplayPort, up to 1920x1200R.

v2: Add Sandybridge support, fix obvious math error.
Acked-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Commit 5a0e3ad6 causes slab.h to be included twice in many of the
Gigaset driver's source files, first via the common include file
gigaset.h and then a second time directly. Drop the spares, and
use the opportunity to clean up a few more similar cases.

Impact: cleanup, no functional change
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
CC: Tejun Heo <tj@kernel.org>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: Ignore LVDS EDID when it is unavailabe or invalid
  drm/i915: Add no_lvds entry for the Clientron U800
  drm/i915: Rename many remaining uses of "output" to encoder or connector.
  drm/i915: Rename intel_output to intel_encoder.
  agp/intel: intel_845_driver is an agp driver!
  drm/i915: introduce to_intel_bo helper
  drm/i915: Disable FBC on 915GM and 945GM.