- 08 9月, 2012 2 次提交
-
-
由 Hadar Hen Zion 提交于
Since VFs may be mapped to VMs which aren't trusted entities, flow steering rules attached through the wrapper on behalf of VFs must be checked to make sure that their L2 specification relate to MAC address assigned to that VF, and add L2 specification if its missing. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hadar Hen Zion 提交于
To allow for usage of the flow steering Firmware structures in more locations over the driver, such as the resource tracker, move them from mcg.c to common header files. Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com> Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 9月, 2012 3 次提交
-
-
由 Santiago Leon 提交于
This patch fixes a bug found by Nish Aravamudan (https://lkml.org/lkml/2012/5/15/220) where the driver is not following the spec (it is not aligning the rx buffer on a 16-byte boundary) and the hypervisor aborts the registration, making the device unusable. The fix follows BenH's recommendation (https://lkml.org/lkml/2012/7/20/461) to replace the kmalloc+map for a single call to dma_alloc_coherent() because that function always aligns to a 16-byte boundary. The stable trees will run into this bug whenever the rx buffer kmalloc call returns something not aligned on a 16-byte boundary. Cc: <stable@vger.kernel.org> Signed-off-by: NSantiago Leon <santil@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Julian Anastasov 提交于
commit 144d56e9 ("tcp: fix possible socket refcount problem") is missing the IPv6 part. As tcp_release_cb is shared by both protocols we should hold sock reference for the TCP_MTU_REDUCED_DEFERRED bit. Signed-off-by: NJulian Anastasov <ja@ssi.bg> Acked-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://gitorious.org/linux-can/linux-can由 David S. Miller 提交于
Marc Kleine-Budde says: ==================== this patch is for the v3.6 release cycle. Benoît Locher fixed a repeated frame bug in the mcp251x driver. He implemented the workaround suggested by the errata sheet. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 9月, 2012 6 次提交
-
-
由 Eric Dumazet 提交于
While investigating l2tp bug, I hit a bug in eth_type_trans(), because not enough bytes were pulled in skb head. Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wu Fengguang 提交于
In znet_probe(), strncmp() may access beyond 0x100000 and trigger the below oops in kvm. Fix it by limiting the loop under 0x100000-8. I suspect the limit could be further decreased to 0x100000-sizeof(struct netidblk), however no datasheet at hand.. [ 3.744312] BUG: unable to handle kernel paging request at 80100000 [ 3.746145] IP: [<8119d12a>] strncmp+0xc/0x20 [ 3.747446] *pde = 01d10067 *pte = 00100160 [ 3.747493] Oops: 0000 [#1] DEBUG_PAGEALLOC [ 3.747493] Pid: 1, comm: swapper Not tainted 3.6.0-rc1-00018-g57bfc0a7 #73 Bochs Bochs [ 3.747493] EIP: 0060:[<8119d12a>] EFLAGS: 00010206 CPU: 0 [ 3.747493] EIP is at strncmp+0xc/0x20 [ 3.747493] EAX: 800fff4e EBX: 00000006 ECX: 00000006 EDX: 814d2bb9 [ 3.747493] ESI: 80100000 EDI: 814d2bba EBP: 8e03dfa0 ESP: 8e03df98 [ 3.747493] DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068 [ 3.747493] CR0: 8005003b CR2: 80100000 CR3: 016f7000 CR4: 00000690 [ 3.747493] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000 [ 3.747493] DR6: ffff0ff0 DR7: 00000400 [ 3.747493] Process swapper (pid: 1, ti=8e03c000 task=8e040000 task.ti=8e03c000) [ 3.747493] Stack: [ 3.747493] 800fffff 00000000 8e03dfb4 816a1376 00000006 816a134a 00000000 8e03dfd0 [ 3.747493] 816819b5 816ed1c0 8e03dfe4 00000006 00000123 816ed604 8e03dfe4 81681b29 [ 3.747493] 00000000 81681a5b 00000000 00000000 8134e542 00000000 00000000 00000000 [ 3.747493] Call Trace: [ 3.747493] [<816a1376>] znet_probe+0x2c/0x26b [ 3.747493] [<816a134a>] ? dnet_driver_init+0xf/0xf [ 3.747493] [<816819b5>] do_one_initcall+0x6a/0x110 [ 3.747493] [<81681b29>] kernel_init+0xce/0x14b Signed-off-by: NFengguang Wu <fengguang.wu@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Steffen Klassert 提交于
ESN for esp is defined in RFC 4303. This RFC assumes that the sequence number counters are always up to date. However, this is not true if an async crypto algorithm is employed. If the sequence number counters are not up to date on sequence number check, we may incorrectly update the upper 32 bit of the sequence number. This leads to a DOS. We workaround this by comparing the upper sequence number, (used for authentication) with the upper sequence number computed after the async processing. We drop the packet if these numbers are different. To do this, we introduce a recheck function that does this check in the ESN case. Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com> Acked-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Fixes following lockdep splat : [ 1614.734896] ============================================= [ 1614.734898] [ INFO: possible recursive locking detected ] [ 1614.734901] 3.6.0-rc3+ #782 Not tainted [ 1614.734903] --------------------------------------------- [ 1614.734905] swapper/11/0 is trying to acquire lock: [ 1614.734907] (slock-AF_INET){+.-...}, at: [<ffffffffa0209d72>] l2tp_xmit_skb+0x172/0xa50 [l2tp_core] [ 1614.734920] [ 1614.734920] but task is already holding lock: [ 1614.734922] (slock-AF_INET){+.-...}, at: [<ffffffff815fce23>] tcp_v4_err+0x163/0x6b0 [ 1614.734932] [ 1614.734932] other info that might help us debug this: [ 1614.734935] Possible unsafe locking scenario: [ 1614.734935] [ 1614.734937] CPU0 [ 1614.734938] ---- [ 1614.734940] lock(slock-AF_INET); [ 1614.734943] lock(slock-AF_INET); [ 1614.734946] [ 1614.734946] *** DEADLOCK *** [ 1614.734946] [ 1614.734949] May be due to missing lock nesting notation [ 1614.734949] [ 1614.734952] 7 locks held by swapper/11/0: [ 1614.734954] #0: (rcu_read_lock){.+.+..}, at: [<ffffffff81592801>] __netif_receive_skb+0x251/0xd00 [ 1614.734964] #1: (rcu_read_lock){.+.+..}, at: [<ffffffff815d319c>] ip_local_deliver_finish+0x4c/0x4e0 [ 1614.734972] #2: (rcu_read_lock){.+.+..}, at: [<ffffffff8160d116>] icmp_socket_deliver+0x46/0x230 [ 1614.734982] #3: (slock-AF_INET){+.-...}, at: [<ffffffff815fce23>] tcp_v4_err+0x163/0x6b0 [ 1614.734989] #4: (rcu_read_lock){.+.+..}, at: [<ffffffff815da240>] ip_queue_xmit+0x0/0x680 [ 1614.734997] #5: (rcu_read_lock_bh){.+....}, at: [<ffffffff815d9925>] ip_finish_output+0x135/0x890 [ 1614.735004] #6: (rcu_read_lock_bh){.+....}, at: [<ffffffff81595680>] dev_queue_xmit+0x0/0xe00 [ 1614.735012] [ 1614.735012] stack backtrace: [ 1614.735016] Pid: 0, comm: swapper/11 Not tainted 3.6.0-rc3+ #782 [ 1614.735018] Call Trace: [ 1614.735020] <IRQ> [<ffffffff810a50ac>] __lock_acquire+0x144c/0x1b10 [ 1614.735033] [<ffffffff810a334b>] ? check_usage+0x9b/0x4d0 [ 1614.735037] [<ffffffff810a6762>] ? mark_held_locks+0x82/0x130 [ 1614.735042] [<ffffffff810a5df0>] lock_acquire+0x90/0x200 [ 1614.735047] [<ffffffffa0209d72>] ? l2tp_xmit_skb+0x172/0xa50 [l2tp_core] [ 1614.735051] [<ffffffff810a69ad>] ? trace_hardirqs_on+0xd/0x10 [ 1614.735060] [<ffffffff81749b31>] _raw_spin_lock+0x41/0x50 [ 1614.735065] [<ffffffffa0209d72>] ? l2tp_xmit_skb+0x172/0xa50 [l2tp_core] [ 1614.735069] [<ffffffffa0209d72>] l2tp_xmit_skb+0x172/0xa50 [l2tp_core] [ 1614.735075] [<ffffffffa014f7f2>] l2tp_eth_dev_xmit+0x32/0x60 [l2tp_eth] [ 1614.735079] [<ffffffff81595112>] dev_hard_start_xmit+0x502/0xa70 [ 1614.735083] [<ffffffff81594c6e>] ? dev_hard_start_xmit+0x5e/0xa70 [ 1614.735087] [<ffffffff815957c1>] ? dev_queue_xmit+0x141/0xe00 [ 1614.735093] [<ffffffff815b622e>] sch_direct_xmit+0xfe/0x290 [ 1614.735098] [<ffffffff81595865>] dev_queue_xmit+0x1e5/0xe00 [ 1614.735102] [<ffffffff81595680>] ? dev_hard_start_xmit+0xa70/0xa70 [ 1614.735106] [<ffffffff815b4daa>] ? eth_header+0x3a/0xf0 [ 1614.735111] [<ffffffff8161d33e>] ? fib_get_table+0x2e/0x280 [ 1614.735117] [<ffffffff8160a7e2>] arp_xmit+0x22/0x60 [ 1614.735121] [<ffffffff8160a863>] arp_send+0x43/0x50 [ 1614.735125] [<ffffffff8160b82f>] arp_solicit+0x18f/0x450 [ 1614.735132] [<ffffffff8159d9da>] neigh_probe+0x4a/0x70 [ 1614.735137] [<ffffffff815a191a>] __neigh_event_send+0xea/0x300 [ 1614.735141] [<ffffffff815a1c93>] neigh_resolve_output+0x163/0x260 [ 1614.735146] [<ffffffff815d9cf5>] ip_finish_output+0x505/0x890 [ 1614.735150] [<ffffffff815d9925>] ? ip_finish_output+0x135/0x890 [ 1614.735154] [<ffffffff815dae79>] ip_output+0x59/0xf0 [ 1614.735158] [<ffffffff815da1cd>] ip_local_out+0x2d/0xa0 [ 1614.735162] [<ffffffff815da403>] ip_queue_xmit+0x1c3/0x680 [ 1614.735165] [<ffffffff815da240>] ? ip_local_out+0xa0/0xa0 [ 1614.735172] [<ffffffff815f4402>] tcp_transmit_skb+0x402/0xa60 [ 1614.735177] [<ffffffff815f5a11>] tcp_retransmit_skb+0x1a1/0x620 [ 1614.735181] [<ffffffff815f7e93>] tcp_retransmit_timer+0x393/0x960 [ 1614.735185] [<ffffffff815fce23>] ? tcp_v4_err+0x163/0x6b0 [ 1614.735189] [<ffffffff815fd317>] tcp_v4_err+0x657/0x6b0 [ 1614.735194] [<ffffffff8160d116>] ? icmp_socket_deliver+0x46/0x230 [ 1614.735199] [<ffffffff8160d19e>] icmp_socket_deliver+0xce/0x230 [ 1614.735203] [<ffffffff8160d116>] ? icmp_socket_deliver+0x46/0x230 [ 1614.735208] [<ffffffff8160d464>] icmp_unreach+0xe4/0x2c0 [ 1614.735213] [<ffffffff8160e520>] icmp_rcv+0x350/0x4a0 [ 1614.735217] [<ffffffff815d3285>] ip_local_deliver_finish+0x135/0x4e0 [ 1614.735221] [<ffffffff815d319c>] ? ip_local_deliver_finish+0x4c/0x4e0 [ 1614.735225] [<ffffffff815d3ffa>] ip_local_deliver+0x4a/0x90 [ 1614.735229] [<ffffffff815d37b7>] ip_rcv_finish+0x187/0x730 [ 1614.735233] [<ffffffff815d425d>] ip_rcv+0x21d/0x300 [ 1614.735237] [<ffffffff81592a1b>] __netif_receive_skb+0x46b/0xd00 [ 1614.735241] [<ffffffff81592801>] ? __netif_receive_skb+0x251/0xd00 [ 1614.735245] [<ffffffff81593368>] process_backlog+0xb8/0x180 [ 1614.735249] [<ffffffff81593cf9>] net_rx_action+0x159/0x330 [ 1614.735257] [<ffffffff810491f0>] __do_softirq+0xd0/0x3e0 [ 1614.735264] [<ffffffff8109ed24>] ? tick_program_event+0x24/0x30 [ 1614.735270] [<ffffffff8175419c>] call_softirq+0x1c/0x30 [ 1614.735278] [<ffffffff8100425d>] do_softirq+0x8d/0xc0 [ 1614.735282] [<ffffffff8104983e>] irq_exit+0xae/0xe0 [ 1614.735287] [<ffffffff8175494e>] smp_apic_timer_interrupt+0x6e/0x99 [ 1614.735291] [<ffffffff81753a1c>] apic_timer_interrupt+0x6c/0x80 [ 1614.735293] <EOI> [<ffffffff810a14ad>] ? trace_hardirqs_off+0xd/0x10 [ 1614.735306] [<ffffffff81336f85>] ? intel_idle+0xf5/0x150 [ 1614.735310] [<ffffffff81336f7e>] ? intel_idle+0xee/0x150 [ 1614.735317] [<ffffffff814e6ea9>] cpuidle_enter+0x19/0x20 [ 1614.735321] [<ffffffff814e7538>] cpuidle_idle_call+0xa8/0x630 [ 1614.735327] [<ffffffff8100c1ba>] cpu_idle+0x8a/0xe0 [ 1614.735333] [<ffffffff8173762e>] start_secondary+0x220/0x222 Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alan Cox 提交于
Check for an error from this and if so bail properly. Signed-off-by: NAlan Cox <alan@linux.intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 9月, 2012 7 次提交
-
-
由 Jesse Gross 提交于
The vlan encapsulation fields in the maximum flow defintion were never updated when the representation changed before upstreaming. In theory this could cause a kernel panic when a maximum length flow is used. In practice this has never happened (to my knowledge) because skb allocations are padded out to a cache line so you would need the right combination of flow and packet being sent to userspace. Signed-off-by: NJesse Gross <jesse@nicira.com>
-
由 Wei Yongjun 提交于
hc has been allocated in this function and missing free it before leaving from some error handling cases. spatch with a semantic match is used to found this problem. (http://coccinelle.lip6.fr/) Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
When fq_codel builds a new flow, it should not reset codel state. Codel algo needs to get previous values (lastcount, drop_next) to get proper behavior. Signed-off-by: NDave Taht <dave.taht@gmail.com> Signed-off-by: NEric Dumazet <edumazet@google.com> Acked-by: NDave Taht <dave.taht@bufferbloat.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Benoît Locher 提交于
The MCP2515 has a silicon bug causing repeated frame transmission, see section 5 of MCP2515 Rev. B Silicon Errata Revision G (March 2007). Basically, setting TXBnCTRL.TXREQ in either SPI mode (00 or 11) will eventually cause the bug. The workaround proposed by Microchip is to use mode 00 and send a RTS command on the SPI bus to initiate the transmission. Cc: <stable@vger.kernel.org> Signed-off-by: NBenoît Locher <Benoit.Locher@skf.com> Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
-
由 Bjørn Mork 提交于
Suspending an open usbnet device results in constant rescheduling of usbnet_bh. commit 65841fd5 "usbnet: handle remote wakeup asap" refactored the usbnet_bh code to allow sharing the urb allocate and submit code with usbnet_resume. In this process, a test for, and immediate return on, ENOLINK from rx_submit was unintentionally dropped. The rx queue will not grow if rx_submit fails, making usbnet_bh reschedule itself. This results in a softirq storm if the error is persistent. rx_submit translates the usb_submit_urb error EHOSTUNREACH into ENOLINK, so this is an expected and persistent error for a suspended device. The old code tested for this condition and avoided rescheduling. Putting this test back. Cc: <stable@vger.kernel.org> # v3.5 Cc: Ming Lei <ming.lei@canonical.com> Cc: Oliver Neukum <oneukum@suse.de> Signed-off-by: NBjørn Mork <bjorn@mork.no> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Thomas Graf 提交于
SCTP charges wmem_alloc via sctp_set_owner_w() in sctp_sendmsg() and via skb_set_owner_w() in sctp_packet_transmit(). If a sender runs out of sndbuf it will sleep in sctp_wait_for_sndbuf() and expects to be waken up by __sctp_write_space(). Buffer space charged via sctp_set_owner_w() is released in sctp_wfree() which calls __sctp_write_space() directly. Buffer space charged via skb_set_owner_w() is released via sock_wfree() which calls sk->sk_write_space() _if_ SOCK_USE_WRITE_QUEUE is not set. sctp_endpoint_init() sets SOCK_USE_WRITE_QUEUE on all sockets. Therefore if sctp_packet_transmit() manages to queue up more than sndbuf bytes, sctp_wait_for_sndbuf() will never be woken up again unless it is interrupted by a signal. This could be fixed by clearing the SOCK_USE_WRITE_QUEUE flag but ... Charging for the data twice does not make sense in the first place, it leads to overcharging sndbuf by a factor 2. Therefore this patch only charges a single byte in wmem_alloc when transmitting an SCTP packet to ensure that the socket stays alive until the packet has been released. This means that control chunks are no longer accounted for in wmem_alloc which I believe is not a problem as skb->truesize will typically lead to overcharging anyway and thus compensates for any control overhead. Signed-off-by: NThomas Graf <tgraf@suug.ch> CC: Vlad Yasevich <vyasevic@redhat.com> CC: Neil Horman <nhorman@tuxdriver.com> CC: David Miller <davem@davemloft.net> Acked-by: NVlad Yasevich <vyasevich@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
sock_edemux() can handle either a regular socket or a timewait socket Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 9月, 2012 3 次提交
-
-
由 Joe Stringer 提交于
Signed-off-by: NJoe Stringer <joe@wand.net.nz> Signed-off-by: NJesse Gross <jesse@nicira.com>
-
git://git.samba.org/sfrench/cifs-2.6由 Linus Torvalds 提交于
Pull CIFS fixes from Steve French. * 'for-next' of git://git.samba.org/sfrench/cifs-2.6: CIFS: Fix cifs_do_create error hadnling cifs: print error code if smb signature verification fails CIFS: Fix log messages in packet checking for SMB2 CIFS: Protect i_nlink from being negative
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking fixes from David Miller: 1) NLA_PUT* --> nla_put_* conversion got one case wrong in nfnetlink_log, fix from Patrick McHardy. 2) Missed error return check in ipw2100 driver, from Julia Lawall. 3) PMTU updates in ipv4 were setting the expiry time incorrectly, fix from Eric Dumazet. 4) SFC driver erroneously reversed src and dst when reporting filters via ethtool. 5) Memory leak in CAN protocol and wrong setting of IRQF_SHARED in sja1000 can platform driver, from Alexey Khoroshilov and Sven Schmitt. 6) Fix multicast traffic scaling regression in ipv4_dst_destroy, only take the lock when we really need to. From Eric Dumazet. 7) Fix non-root process spoofing in netlink, from Pablo Neira Ayuso. 8) CWND reduction in TCP is done incorrectly during non-SACK recovery, fix from Yuchung Cheng. 9) Revert netpoll change, and fix what was actually a driver specific problem. From Amerigo Wang. This should cure bootup hangs with netconsole some people reported. 10) Fix xen-netfront invoking __skb_fill_page_desc() with a NULL page pointer. From Ian Campbell. 11) SIP NAT fix for expectiontation creation, from Pablo Neira Ayuso. 12) __ip_rt_update_pmtu() needs RCU locking, from Eric Dumazet. 13) Fix usbnet deadlock on resume, can't use GFP_KERNEL in this situation. From Oliver Neukum. 14) The davinci ethernet driver triggers an OOPS on removal because it frees an MDIO object before unregistering it. Fix from Bin Liu. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits) net: qmi_wwan: add several new Gobi devices fddi: 64 bit bug in smt_add_para() net: ethernet: fix kernel OOPS when remove davinci_mdio module net/xfrm/xfrm_state.c: fix error return code net: ipv6: fix error return code net: qmi_wwan: new device: Foxconn/Novatel E396 usbnet: fix deadlock in resume cs89x0 : packet reception not working netfilter: nf_conntrack: fix racy timer handling with reliable events bnx2x: Correct the ndo_poll_controller call bnx2x: Move netif_napi_add to the open call ipv4: must use rcu protection while calling fib_lookup bnx2x: fix 57840_MF pci id net: ipv4: ipmr_expire_timer causes crash when removing net namespace e1000e: DoS while TSO enabled caused by link partner with small MSS l2tp: avoid to use synchronize_rcu in tunnel free function gianfar: fix default tx vlan offload feature flag netfilter: nf_nat_sip: fix incorrect handling of EBUSY for RTCP expectation xen-netfront: use __pskb_pull_tail to ensure linear area is big enough on RX netfilter: nfnetlink_log: fix error return code in init path ...
-
- 02 9月, 2012 4 次提交
-
-
由 Bjørn Mork 提交于
Gobi devices are composite, needing both the qcserial and qmi_wwan drivers to support all functions. Re-syncing the list of supported devices with qcserial. Cc: Aleksander Morgado <aleksander@lanedo.com> Cc: Thomas Tuttle <ttuttle@chromium.org> Signed-off-by: NBjørn Mork <bjorn@mork.no> Signed-off-by: NDavid S. Miller <davem@tempietto.lan>
-
由 Dan Carpenter 提交于
The intent was to set 4 bytes of data so that's why the sp_len is set to 4 on the next line. The cast to u_long pointer clears 8 bytes on 64 bit arches. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NDavid S. Miller <davem@tempietto.lan>
-
由 Linus Torvalds 提交于
-
由 John Stultz 提交于
Andreas Bombe reported that the added ktime_t overflow checking added to timespec_valid in commit 4e8b1452 ("time: Improve sanity checking of timekeeping inputs") was causing problems with X.org because it caused timeouts larger then KTIME_T to be invalid. Previously, these large timeouts would be clamped to KTIME_MAX and would never expire, which is valid. This patch splits the ktime_t overflow checking into a new timespec_valid_strict function, and converts the timekeeping codes internal checking to use this more strict function. Reported-and-tested-by: NAndreas Bombe <aeb@debian.org> Cc: Zhouping Liu <zliu@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: NJohn Stultz <john.stultz@linaro.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 01 9月, 2012 10 次提交
-
-
git://git.kernel.org/pub/scm/virt/kvm/kvm由 Linus Torvalds 提交于
Pull KVM bugfixes from Marcelo Tosatti. * git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: fix KVM_GET_MSR for PV EOI kvm: Fix nonsense handling of compat ioctl
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6由 Linus Torvalds 提交于
Pull PARISC fixes from James Bottomley: "This is a set of two bug fixes. One is the ATOMIC problem which is now causing a compile failure in certain situations. The other is mishandling of PER_LINUX32 which may also cause user visible effects. Signed-off-by: James Bottomley <JBottomley@Parallels.com>" * tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6: [PARISC] fix personality flag check in copy_thread() [PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts
-
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux由 Linus Torvalds 提交于
Pull s390 fixes from Martin Schwidefsky: "A couple of s390 bug fixes for 3.5-rc4" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/32: Don't clobber personality flags on exec s390/smp: add missing smp_store_status() for !SMP s390/dasd: fix ioctl return value s390: Always use "long" for ssize_t to match size_t
-
由 Bin Liu 提交于
davinci mdio device is not unregistered from mdiobus when removing the module, which causes BUG_ON() when free the device from mdiobus. Calling mdiobus_unregister() before mdiobus_free() fixes the issue. Signed-off-by: NBin Liu <b-liu@ti.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Julia Lawall 提交于
Initialize return variable before exiting on an error path. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> ( if@p1 (\(ret < 0\|ret != 0\)) { ... return ret; } | ret@p1 = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Julia Lawall 提交于
Initialize return variable before exiting on an error path. The initial initialization of the return variable is also dropped, because that value is never used. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> ( if@p1 (\(ret < 0\|ret != 0\)) { ... return ret; } | ret@p1 = 0 ) ... when != ret = e1 when != &ret *if(...) { ... when != ret = e2 when forall return ret; } // </smpl> Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Aleksander Morgado 提交于
Foxconn-branded Novatel E396, Gobi3k modem. Cc: Dan Williams <dcbw@redhat.com> Cc: Bjørn Mork <bjorn@mork.no> Cc: Ben Chan <benchan@google.com> Signed-off-by: NAleksander Morgado <aleksander@lanedo.com> Acked-by: NBjørn Mork <bjorn@mork.no> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Oliver Neukum 提交于
A usbnet device can share a multifunction device with a storage device. If the storage device is autoresumed the usbnet devices also needs to be autoresumed. Allocating memory with GFP_KERNEL can deadlock in this case. This should go back into all kernels that have commit 65841fd5 That is 3.5 Signed-off-by: NOliver Neukum <oneukum@suse.de> CC: stable@kernel.org Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jaccon Bastiaansen 提交于
The RxCFG register of the CS89x0 could be configured incorrectly (because of misplaced parentheses), resulting in the disabling of packet reception. Signed-off-by: NJaccon Bastiaansen <jaccon.bastiaansen@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
-
- 31 8月, 2012 5 次提交
-
-
由 Pablo Neira Ayuso 提交于
Existing code assumes that del_timer returns true for alive conntrack entries. However, this is not true if reliable events are enabled. In that case, del_timer may return true for entries that were just inserted in the dying list. Note that packets / ctnetlink may hold references to conntrack entries that were just inserted to such list. This patch fixes the issue by adding an independent timer for event delivery. This increases the size of the ecache extension. Still we can revisit this later and use variable size extensions to allocate this area on demand. Tested-by: NOliver Smith <olipro@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Merav Sicron 提交于
This patch correct poll_bnx2x (ndo_poll_controller call) which was not functioning well with MSI-X. Signed-off-by: NMerav Sicron <meravs@broadcom.com> Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Merav Sicron 提交于
Move netif_napi_add for all queues from the probe call to the open call, to avoid the case that napi objects are added for queues that may eventually not be initialized and activated. With the former behavior, the driver could crash when netpoll was calling ndo_poll_controller. Signed-off-by: NMerav Sicron <meravs@broadcom.com> Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Following lockdep splat was reported by Pavel Roskin : [ 1570.586223] =============================== [ 1570.586225] [ INFO: suspicious RCU usage. ] [ 1570.586228] 3.6.0-rc3-wl-main #98 Not tainted [ 1570.586229] ------------------------------- [ 1570.586231] /home/proski/src/linux/net/ipv4/route.c:645 suspicious rcu_dereference_check() usage! [ 1570.586233] [ 1570.586233] other info that might help us debug this: [ 1570.586233] [ 1570.586236] [ 1570.586236] rcu_scheduler_active = 1, debug_locks = 0 [ 1570.586238] 2 locks held by Chrome_IOThread/4467: [ 1570.586240] #0: (slock-AF_INET){+.-...}, at: [<ffffffff814f2c0c>] release_sock+0x2c/0xa0 [ 1570.586253] #1: (fnhe_lock){+.-...}, at: [<ffffffff815302fc>] update_or_create_fnhe+0x2c/0x270 [ 1570.586260] [ 1570.586260] stack backtrace: [ 1570.586263] Pid: 4467, comm: Chrome_IOThread Not tainted 3.6.0-rc3-wl-main #98 [ 1570.586265] Call Trace: [ 1570.586271] [<ffffffff810976ed>] lockdep_rcu_suspicious+0xfd/0x130 [ 1570.586275] [<ffffffff8153042c>] update_or_create_fnhe+0x15c/0x270 [ 1570.586278] [<ffffffff815305b3>] __ip_rt_update_pmtu+0x73/0xb0 [ 1570.586282] [<ffffffff81530619>] ip_rt_update_pmtu+0x29/0x90 [ 1570.586285] [<ffffffff815411dc>] inet_csk_update_pmtu+0x2c/0x80 [ 1570.586290] [<ffffffff81558d1e>] tcp_v4_mtu_reduced+0x2e/0xc0 [ 1570.586293] [<ffffffff81553bc4>] tcp_release_cb+0xa4/0xb0 [ 1570.586296] [<ffffffff814f2c35>] release_sock+0x55/0xa0 [ 1570.586300] [<ffffffff815442ef>] tcp_sendmsg+0x4af/0xf50 [ 1570.586305] [<ffffffff8156fc60>] inet_sendmsg+0x120/0x230 [ 1570.586308] [<ffffffff8156fb40>] ? inet_sk_rebuild_header+0x40/0x40 [ 1570.586312] [<ffffffff814f4bdd>] ? sock_update_classid+0xbd/0x3b0 [ 1570.586315] [<ffffffff814f4c50>] ? sock_update_classid+0x130/0x3b0 [ 1570.586320] [<ffffffff814ec435>] do_sock_write+0xc5/0xe0 [ 1570.586323] [<ffffffff814ec4a3>] sock_aio_write+0x53/0x80 [ 1570.586328] [<ffffffff8114bc83>] do_sync_write+0xa3/0xe0 [ 1570.586332] [<ffffffff8114c5a5>] vfs_write+0x165/0x180 [ 1570.586335] [<ffffffff8114c805>] sys_write+0x45/0x90 [ 1570.586340] [<ffffffff815d2722>] system_call_fastpath+0x16/0x1b Signed-off-by: NEric Dumazet <edumazet@google.com> Reported-by: NPavel Roskin <proski@gnu.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Commit c3def943 have added support for new pci ids of the 57840 board, while failing to change the obsolete value in 'pci_ids.h'. This patch does so, allowing the probe of such devices. Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-