When endpoint changes (due to it being disabled or alt setting changed),
mimic the action as if the change happened after the request has been
queued, instead of retrying with the new endpoint.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use usb_add_phy_dev instead of usb_add_phy, so that devices can
be bound to the phy. This is needed to set up USB phy for
some internal PCI USB host controllers on R-Car Gen2.
Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

the lock was only taken inside the hardirq
handler, which runs with IRQs disabled. There's
no chance of any race condition happening, even
on SMP machines. It's safe to remove that
spinlock.
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add Tahvo USB transceiver driver.

Based on old code from linux-omap tree. The original driver was written
by Juha Yrjölä, Tony Lindgren, and Timo Teräs.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Transceivers need to manage OTG controller state on OMAP1 to enable
switching between peripheral and host modes. Provide a driver for that.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Acked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add support for using the sourcesink function in gadgets composed with
configfs.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add support for using the loopback USB function in gadgets composed with
configfs.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

alloc_ep_req() is a function repeated in several modules.
Make a common implementation and use it.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If there are setup requests not directed to an endpont or an interface,
current config's setup() has been attempted so far.
This patch, in case the above fails, adds code which tries the setup() of
configuration's function if there is only one function in the configuration.

This behavior is required to provide equivalent of gadget zero with configfs.

The gadget zero has a "config driver" for sourcesink, but all it does is
delegating the request to the function proper. So when the equivalent gadget
is set up with configfs it needs to handle requests directed to
"config driver", but with configfs it is not possible to specify
"config drivers".
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Only start the otg_timer in dual role mode; otherwise in peripheral mode
when musb is disconnected from the host port, otg_timer starts and
continuously toggles the session, which causes VBUS pulse.
Signed-off-by: NBin Liu <b-liu@ti.com>
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch removes dependency on Freescale USB UTG Transceiver
driver and makes OTG FSM implementation selectable.
Signed-off-by: NAnton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Other USB drivers may want to use OTG final state machine
implementation, so make this header available for them.
Signed-off-by: NAnton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

OTG Final State Machine calls functions which may sleep.

For example, start_gadget callback implementation can use
usb_gadget_vbus_connect(), whose context: can sleep.

If so, mutex should be used instead of spinlock.
Signed-off-by: NAnton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

if this header is included twice, we would have
redefinition build errors. Fix this.
Signed-off-by: NAnton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this header uses spinlocks and errno values, so
we must include <linux/spinlock.h> and <linux/errno.h>
to avoid build errors.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

These functions used to return negative errror codes but now they return
ERR_PTRs.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

device_driver.name is "const char *"
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The stop_activity function never uses driver argument (even
though it modifies it) and thus it is safe to remove it.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we have a helper to fetch endpoint type out of
a descriptor, let's use it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The dsps platform needs to save save some registers at suspend time and
restore them after resume. This patch adds a struct for these registers,
and also lets the musb core know that the core registers need to be
saved as well.

We also have to explicitly de-assert the port reset upon resume on this
platform, but musb_port_reset() should not be called from glue layers.

Hence, introduce a flag in struct musb_hdrc_config for this.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

rx_mode and tx_mode need to be read at suspend time and restored on
resume for dsps platforms. So add it to the wrapper struct first, and
initialize the values.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Make musb_port_suspend() externally available, and call it when to host
goes into suspend. This allows the core to go into suspend while a
device is connected.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It appears not all platforms featuring a musb core need to save the musb
core registers at suspend time and restore them on resume.

The dsps platform does, however, and because it shouldn't cause any
trouble on other platforms, do it unconditionally for all of them.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Due to inter dependencies of I2C and extcon by the time dwc3
checks for extcon device its not registered especially in case of J6.
In O5 the vbus regulator save us from getting to this point.
So for tiime being return PROBE_DEFER if extcon is enabled in dt.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>

This will tell glue layer which mode we want port
to be in.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this will let us support broken designs such
as AM335x EVM SK where ID pin isn't routed
anywhere on a host port.

With this we can toggle internal IDDIG signal
and make sure MUSB goes into host mode as
necessary.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.

Cc: Felipe Balbi <balbi@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.

[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since DEVICE_ACPI_HANDLE() is now literally identical to
ACPI_HANDLE(), replace it with the latter everywhere and drop its
definition from include/acpi.h.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Custom VID/PID for Z3X Box device, popular tool for cellphone flashing.
Signed-off-by: NAlexey E. Kramarenko <alexeyk13@yandex.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit b8bdad60.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 57ce61aa.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: pl2303: do not round to the next nearest standard baud rate for the divisor based baud rate encoding method"

This reverts commit 75417d9f.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit b9208c72.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit e917ba01.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit b5c16c6a.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>