pgm_ratios in stored as a register value in pipe config, so let's dump
this one as hex as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-15-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Use the proper refclock frequency (100MHz) when reading out the
current DSI clock on CHV.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-13-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

On VLV at least, the BIOS may leave the DSI PLL enabled in some wonky
state where it just refuses to lock. Simply disabling the PLL before
reconfiguring it is not enough to fix it, but power gating the PLL
prior to reconfiguring does work.

This happens on BYT FFRD8 when booting with HDMI connected so the DSI
display will not be lit up by the BIOS.

Also we can remove the code for BXT that disables the PLL before
enabling it again.

v2: s/vlv/intel/ since BXT made thing generic
v3: Remove the BXT disable PLL before enable trick
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-11-git-send-email-ville.syrjala@linux.intel.comAcked-by: NJani Nikula <jani.nikula@intel.com>

All the values in the DSI PLL LFSR seed table fit into 9bits, so change
the type to u16 from u32 to save a bit of space.

 drivers/gpu/drm/i915/i915.ko:
-.rodata                        90824
+.rodata                        90760
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-10-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Enable the unclaimd register detection stuff on vlv/chv since we've now
fixed the known problems during suspend.

This reverts commit c81eeea6.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-11-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

DPINVGTT lives inside the disp2d power well so we can't frob it unless
we know the power well is active. Let's this stuff into
vlv_display_irq_reset() which is only called at the right times so that
we don't get unclaimed register access errors.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-10-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

The registers frobbed by vlv_init_display_clock_gating() libve inside
the disp2d power well, so frobbing them while the power well is down
results in unclaimed register access warning (and of course the values
won't stick). Let's do this setup after we know the power well is
enabled.

It's also worth noting that DSPCLK_GATE_D and CBR1_VLV lose their state
when the power well goes down, but fortunately the values we've been
writing are actually the reset defaults.

MI_ARB_VLV actually retains its value even if the power well was turned
off, we just can't access it while the power well is down.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-9-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

We expect vlv_display_irq_reset() to have been called prior to
vlv_display_irq_postinstall() so let's WARN if that isn't the case.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-8-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Replace the hand rolled IMR/IER setup in vlv_display_irq_postinstall()
with GEN5_IRQ_INIT(). Also rename the iir_mask to enable_mask to avoid
consusion since we no longer deal with IIR here.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-7-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

For a bit of extra paranoia make sure the display irqs are all cleared
before we enabled them when turning on the power well. This should
really be the case already since the power well was off which resets
everything.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-6-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Reshuffle the code a bit to move the vlv/chv display irq functions away
from the main irq hooks, next to the other sub (de,gt,etc.) hooks.

v2: Rebased due to changes in vlv_display_irq_reset()
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1460476604-2035-1-git-send-email-ville.syrjala@linux.intel.com

During runtime PM we'll be reinitializing interrupt support from the
ground up. However since the display power well will be off at that
time, well end up with a ton of unclaimed register accesses from the
display irq setup. Since we turned off the power well already before
runtime suspend, we've flagged display irqs as disabled during runtime
PM transitions. So we can just check that flag to see if we should do
skip display irqs during irq setup.

During driver load display irqs will be flagged as enabled since we've
turned on the power well already, however the power well code will have
skipped the display irq setup since irq support as a whole wasn't yet
enabled when the power well was enabled. So we'll want to do the display
irq setup in that case.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

The vlv/chv display irq setup was a bit of mess after I ran out of steam
when working on it last. Fix it up so that we just have a _reset() and
_postinstall() hooks for the display irqs, and use those consistently.

v2: Clear out pipestat_irq_mask[] and PIPE_FIFO_UNDERRUN_STATUS in
    vlv_display_irq_reset() (Imre)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1460476574-1921-1-git-send-email-ville.syrjala@linux.intel.com

No clue what this is supposed to achieve. I think it's been there since
the very beginning, so presumably some kind of kludge for very early
silicon. Let's just throw it out.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

The underruns we were seeing when enabling eDP port A on ILK seem to
have been caused by prematurely clearing the LP1+ watermark values when
disabling LP1+ watermarks. Now that the watermarks are handled
properly, we can rip out the underrun suppression around the port A
enable.

We still need to worry about the underruns on FDI when enabling
the eDP PLL. But as Bspec tells us, we can avoid that by a vblank
wait on the pipe driving FDI just prior to enabling the eDP PLL.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>

Once again ILK is unhappy if we clear out the LP1+ watermark levels
outright, and instead we must disable the levels we don't want while
still leaving the actual programmed watermark levels intact.

Fixes underruns on the already enabled pipe when programming watermarks
while enabling the second pipe.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matt Roper <matthew.d.roper@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93787Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>

Take a bigger hammer to the underrun suppression on ILK. Instead of
trying to suppress them at specific points in the modeset sequence just
silence them across the entire sequence. This gets rid of some underruns
at least on my ILK. Note that this changes SNB and IVB to follow the
same approach just to keep the code less convoluted. The difference is
that on those platforms we won't suppress CPU underruns for port A since
it doesn't seem to be necessary.

My ILK has port A eDP and two PCH HDMI ports, so I can't be sure this is
as effective on other PCH port types. Perhaps we still need some of
Daniel's extra vblank waits [2]?

I've still been able to trigger an underrun on the other pipe, but
fixing that perhaps needs the LP1+ disable trick I implemented here [1]
which never got merged.

A few details which hamper stress testing on my ILK are that sometimes
the PCH transcoder gets messed up and refuses to shut down, and sometimes
even the panel power sequencer apparently gets stuck on the always on
position.

[1] https://lists.freedesktop.org/archives/intel-gfx/2014-March/041317.html
[2] https://lists.freedesktop.org/archives/intel-gfx/2016-January/086397.html

v2: Add a note that we also get underruns when enabling PCH ports

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>

Rather than blindly waking up all forcewake domains on command
submission, we can teach each engine what is (or are) the correct
one to take.

On platforms with multiple forcewake domains like VLV, CHV, SKL
and BXT, this has the potential of lowering the GPU and CPU
power use and submission latency.

To implement it we add a function named
intel_uncore_forcewake_for_reg whose purpose is to query which
forcewake domains need to be taken to read or write a specific
register with raw mmio accessors.

These enables the execlists engine setup  to query which
forcewake domains are relevant per engine on the currently
running platform.

v2:
  * Kerneldoc.
  * Split from intel_uncore.c macro extraction, WARN_ON,
    no warns on old platforms. (Chris Wilson)

v3:
  * Single domain per engine, mention all registers,
    bi-directional function and a new name, fix handling
    of gen6 and gen7 writes. (Chris Wilson)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460468251-14069-1-git-send-email-tvrtko.ursulin@linux.intel.com

Chris Wilson points out that we can remove them from the array
since they are always written to with raw accessors.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Knowledge of which register per platform belonds in which
forcewake domain was embedded in the MMIO accessors themselves.

Extract it into standalone macros so they can be used from
new code in the following patches.

This causes GCC to compile some of the MMIO accessors slightly
differently and grows the code a tiny amount. But none of the
growth is on the fast-path so it does not matter hugely.

Affected sizes before:

00000000000026f0 00000000000001a5 t gen6_read16
0000000000002390 00000000000001a5 t gen6_read32
00000000000028a0 00000000000001a5 t gen6_read64

00000000000061d0 000000000000019e t gen8_write16
0000000000006510 000000000000019d t gen8_write32
0000000000006370 000000000000019d t gen8_write64
00000000000021f0 000000000000019d t gen8_write8

Affected sizes after:

0000000000002840 00000000000001aa t gen6_read16
00000000000024e0 00000000000001a9 t gen6_read32
00000000000029f0 00000000000001a9 t gen6_read64

0000000000004f20 00000000000001b5 t gen8_write16
0000000000004ba0 00000000000001b4 t gen8_write32
00000000000050e0 00000000000001b4 t gen8_write64
0000000000004d60 00000000000001b4 t gen8_write8

Other MMIO accessors are not affected in size.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

On platforms with multiple forcewake domains it seems more efficient
to request all desired ones and then to wait for acks to avoid
needlessly serializing on each domain.

v2: Rebase.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460045074-1006-1-git-send-email-tvrtko.ursulin@linux.intel.com

As the vast majority of users do not use the domain id variable,
we can eliminate it from the iterator and also change the latter
using the same principle as was recently done for for_each_engine.

For a couple of callers which do need the domain mask, store it
in the domain array (which already has the domain id), then both
can be retrieved thence.

Result is clearer code and smaller generated binary, especially
in the tight fw get/put loops. Also, relationship between domain
id and mask is no longer assumed in the macro.

v2: Improve grammar in the commit message and rename the
    iterator to for_each_fw_domain_masked for consistency.
    (Dave Gordon)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDave Gordon <david.s.gordon@intel.com>

Because it is based on jiffies, current implementation releases the
forcewake at any time between straight away and between 1ms and 10ms,
depending on the kernel configuration (CONFIG_HZ).

This is probably not what has been desired, since the dynamics of keeping
parts of the GPU awake should not be correlated with this kernel
configuration parameter.

Change the auto-release mechanism to use hrtimers and set the timeout to
1ms with a 1ms of slack. This should make the GPU power consistent
across kernel configs, and timer slack should enable some timer coalescing
where multiple force-wake domains exist, or with unrelated timers.

For GlBench/T-Rex this decreases the number of forcewake releases from
~480 to ~300 per second, and for a heavy combined OGL/OCL test from
~670 to ~360 (HZ=1000 kernel).

Even though this reduction can be attributed to the average release period
extending from 0-1ms to 1-2ms, as discussed above, it will make the
forcewake timeout consistent for different CONFIG_HZ values.

Real life measurements with the above workload has shown that, with this
patch, both manage to auto-release the forcewake between 2-4 times per
10ms, even though the number of forcewake gets is dramatically different.

T-Rex requests between 5-10 explicit gets and 5-10 implict gets in each
10ms period, while the OGL/OCL test requests 250 and 380 times in the same
period.

The two data points together suggest that the nature of the forwake
accesses is bursty and that further changes and potential timeout
extensions, or moving the start of timeout from the first to the last
automatic forcewake grab, should be carefully measured for power and
performance effects.

v2:
  * Commit spelling. (Dave Gordon)
  * More discussion on numbers in the commit. (Chris Wilson)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

We've had problems on several occasions with using the panel type
from the VBT block 40. Usually it seems to be 2, which often
doesn't give us the correct timings for the panel. After some
more digging I found a way to get a panel type via the OpRegion
SWSCI GBDA "Get Panel Details" method. Let's try to use it.

The spec has this to say about the output:
"Bits [15:8] - Panel Type
 Bits contain the panel type user setting from CMOS
 00h = Not Valid, use default Panel Type & Timings from VBT
 01h - 0Fh = Panel Number"

Another version of the spec lists the valid range as 1-16, which makes
more sense since VBT supports 16 panels. Based on actual results
from Rob's G45, 1-16 is what we need to accept.

The other bits in the output don't look relevant for the problem at
hand.

The input is specified as:
"Bits [31:4] - Reserved
 Reserved (must be zero)
 Bits [3:0] - Panel Number
 These bits contain the sequential index of Panel, starting at 0 and
 counting upwards from the first integrated Internal Flat-Panel Display
 Encoder present, and then from the first external Display Encoder
 (e.g., S/DVO-B then S/DVO-C) which supports Internal Flat-Panels.
 0h - 0Fh = Panel number"

For now I've just hardcoded the input panel number as 0. That would seem
like a decent choise for LVDS. Not so sure about eDP when port != A.

v2: Accept values 1-16
    Filter out bogus results in opregion code (Jani)
    Add debug logging for all the different branches (Jani)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rob Kramer <rob@solution-space.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94825Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460359431-11003-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>
Tested-by: NRob Kramer <rob@solution-space.com>

Store the extracted panel_type under dev_priv.vbt instead of keeping
around a static variable for it.

Cc: Rob Kramer <rob@solution-space.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>

VBT can only contain 16 panel entries, indexed with the panel_type.
To play it safe we should reject panel_type > 0xf, so that we don't
read past the valid data.

v2: Add debug logging (Jani)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rob Kramer <rob@solution-space.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1460359329-10817-1-git-send-email-ville.syrjala@linux.intel.com

There's no real reason the user should care that we're about to fall
back to bitbanging, so let's change the message from DRM_INFO to
DRM_DEBUG_KMS.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457366220-29409-5-git-send-email-ville.syrjala@linux.intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94890Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

When the GMBUS based i2c transfer times out, we try to fall back to
bit-banging and retry the operation that way. However if the bit-banging
attempt also fails, we should probably go back to the GMBUS method for
the next attempt. Maybe there simply wasn't anyone one the bus at this
time.

There's also a bit of a mess going on with the force_bit handling.
It's supposed to be a ref count actually, and it is as far as
intel_gmbus_force_bit() is concerned. But it's treated as just a
flag by the timeout based bit-banging fallback. I suppose that's
fine since we should never end up in the timeout fallback case
if force_bit was already non-zero. However now that we want to restore
things back to where they were after the bit-banging attempt failed,
we're going to have to do things a bit differently to avoid clobbering
the force_bit count as set up by intel_gmbus_force_bit(). So let's
dedicate the high bit as a flag for the low level timeout based fallback
and treat the rest of the bits as a ref count just as before.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457366220-29409-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Extend the protection of gmbus_mutex around the force_bit
RMW in intel_gmbus_force_bit(), in case someone gets the
idea of calling it from a separate thread while there's
other stuff happening on the same bus.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457366220-29409-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Since we only ever use the drm_i915_private from the stored
i915_mm_struct->dev, save some electrons by storing the right
backpointer.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-3-git-send-email-chris@chris-wilson.co.uk

Holding a reference to the containing task_struct is not sufficient to
prevent the mm_struct from being reaped under memory pressure. If this
happens whilst we are calling get_user_pages(), explosions erupt -
sometimes an immediate GPF, sometimes page flag corruption. To prevent
the target mm from being reaped as we are reading from it, acquire a
reference before we begin.

Testcase: igt/gem_shrink/*userptr
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-2-git-send-email-chris@chris-wilson.co.uk

In order to ensure that all invalidations are completed before the
operation returns to userspace (i.e. before the munmap() syscall returns)
we need to wait upon the outstanding operations.

We are allowed to block inside the invalidate_range_start callback, and
as struct_mutex is the inner lock with mmap_sem we can wait upon the
struct_mutex without provoking lockdep into warning about a deadlock.
However, we don't actually want to wait upon outstanding rendering
whilst holding the struct_mutex if we can help it otherwise we also
block other processes from submitting work to the GPU. So first we do a
wait without the lock and then when we reacquire the lock, we double
check that everything is ready for removing the invalidated pages.

Finally to wait upon the outstanding unpinning tasks, we create a
private workqueue as a means to conveniently wait upon all at once. The
drawback is that this workqueue is per-mm, so any threads concurrently
invalidating objects will wait upon each other. The advantage of using
the workqueue is that we can wait in parallel for completion of
rendering and unpinning of several objects (of particular importance if
the process terminates with a whole mm full of objects).

v2: Apply a cup of tea to the changelog.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94699
Testcase: igt/gem_userptr_blits/sync-unmap-cycles
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-1-git-send-email-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Linux 4.6-rc3

Backmerge requested by Chris Wilson to make his patches apply cleanly.
Tiny conflict in vmalloc.c with the (properly acked and all) patch in
drm-intel-next:

commit 4da56b99
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Mon Apr 4 14:46:42 2016 +0100

    mm/vmap: Add a notifier for when we run out of vmap address space

and Linus' tree.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

If we want a contiguous mapping of a single page sized object, we can
forgo using vmap() and just use a regular kmap(). Note that this is only
suitable if the desired pgprot_t is compatible.

v2: Use is_vmalloc_addr()
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-7-git-send-email-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>

I have instances where I want to use drm_malloc_ab() but with a custom
gfp mask. And with those, where I want a temporary allocation, I want to
try a high-order kmalloc() before using a vmalloc().

So refactor my usage into drm_malloc_gfp().
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NDave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-6-git-send-email-chris@chris-wilson.co.uk

When called because we have run out of vmap address space, we only need
to recover objects that have vmappings and not all.

v2: Start using is_vmalloc_addr()
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-5-git-send-email-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>

We now have two implementations for vmapping a whole object, one for
dma-buf and one for the ringbuffer. If we couple the mapping into the
obj->pages lifetime, then we can reuse an obj->mapping for both and at
the same time couple it into the shrinker. There is a third vmapping
routine in the cmdparser that maps only a range within the object, for
the time being that is left alone, but will eventually use these routines
in order to cache the mapping between invocations.

v2: Mark the failable kmalloc() as __GFP_NOWARN (vsyrjala)
v3: Call unpin_vmap from the right dmabuf unmapper

v4: Rename vmap to map as we don't wish to imply the type of mapping
involved, just that it contiguously maps the object into kernel space.
Add kerneldoc and lockdep annotations
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-4-git-send-email-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>

After we pin the ringbuffer into the GGTT, all error paths need to unpin
it again. Move this common step into one block, and make the unable to
iomap error code consistent (i.e. treat it as out of memory to avoid
confusing it with a invalid argument).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-3-git-send-email-chris@chris-wilson.co.uk

We only need the struct_mutex to manipulate the pages_pin_count on the
object, we do not need to hold our BKL when freeing the exported
scatterlist.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-2-git-send-email-chris@chris-wilson.co.uk