According to the common clock framework API, the clk_get_parent() function
should return u8. Currently we are returning negative values on error. Fix
this and use the default parent in case of an error.
Signed-off-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Currently, a RCG's M/N counter (used for fraction division) is
set to either 'bypass' (counter disabled) or 'dual edge' (counter
enabled) based on whether the corresponding rcg struct has a mnd
field specified and a non-zero N.

In the case where M and N are the same value, the M/N counter is
still enabled by code even though no division takes place.
Leaving the RCG in such a state can result in improper behavior.
This was observed with the DSI pixel clock RCG when M and N were
both set to 1.

Add an additional check (M != N) to enable the M/N counter only
when it's needed for fraction division.
Signed-off-by: NArchit Taneja <architt@codeaurora.org>
Fixes: bcd61c0f (clk: qcom: Add support for root clock
generators (RCGs))
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

clock changes for mvebu for v4.1

- Add clock support for Armada 39x

of_clk_get_by_clkspec() has the same function signature as
of_clk_get_from_provider()

 struct clk *of_clk_get_by_clkspec(struct of_phandle_args
 *clkspec)
 struct clk *of_clk_get_from_provider(struct of_phandle_args
 *clkspec)

except of_clk_get_by_clkspec() checks to make sure clkspec is not
NULL. Let's remove of_clk_get_by_clkspec() and replace the
callers of it (clkconf.c) with of_clk_get_from_provider().

Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

The child_node member of struct clk is named the same as the
child_node member of struct clk_core. Let's rename the struct
clk's member to clks_node to avoid getting confused with the
child_node member of struct clk_core and to match the name of the
list head, clks.
Reviewed-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Alban Browaeys <alban.browaeys@gmail.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

The ahbix clock can never be turned off in practice. To change the
rates we need to switch the mux off the M/N counter to an always on
source (XO), reprogram the M/N counter to get the rate we want and
finally switch back to the M/N counter. Add a new ops structure
for this type of clock so that we can set the rate properly.

Fixes: c99e515a "clk: qcom: Add IPQ806X LPASS clock controller (LCC) driver"
Tested-by: NKenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Clock controller driver for Exynos 5433 SoC.

PXO is 25MHz, not 27MHz. Fix the table.

Fixes: 24d8fba4 "clk: qcom: Add support for IPQ8064's global
clock controller (GCC)"
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Reviewed-by: NAndy Gross <agross@codeaurora.org>
Tested-by: NAndy Gross <agross@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

If a driver calls clk_set_parent(clk, parent) and parent is the
current parent of clk we shouldn't fail in any case.
Unfortunately if clk is a read-only mux we return -ENOSYS
because we think we can't change the parent, except for in this
special case where we don't actually need to change the parent at
all. Return 0 in such a situation.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

It's useful to have tracepoints around operations that change the
hardware state so that we can debug clock hardware performance
and operations. Four basic types of events are supported: on/off
events for enable, disable, prepare, unprepare that only record
an event and a clock name, rate changing events for
clk_set_{min_,max_}rate{_range}(), phase changing events for
clk_set_phase() and parent changing events for clk_set_parent().

Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

If a clock's clk_ops doesn't have the set_phase op set we should
return an error from clk_set_phase(). This way clock consumers
know that when they tried to set a phase it didn't work, as
opposed to the current behavior where the return value is 0
meaning success.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

If the divider or multiplier values are 0 in the register, bypassing the
divider and returning the parent clock rate in clk_fd_recalc_rate().
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: fixed commitlog typo]

Add lockdep asserts for holding the prepare_lock to all functions
marking this as a requirement in description. Add this to private and
exported functions so all locking misuse could be detected during
debugging.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

Since commit 035a61c3 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers.  That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get().  This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place.  The net change here is before commit
035a61c3 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.

That said, the struct clk pointer comparing in the code doesn't work any
more.  Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Since commit 035a61c3 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers.  That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get().  This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place.  The net change here is before commit
035a61c3 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.

That said, the struct clk pointer comparing in the code doesn't work any
more.  Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Since commit 035a61c3 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers.  That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get().  This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place.  The net change here is before commit
035a61c3 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.

That said, the struct clk pointer comparing in the code doesn't work any
more.  Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Some drivers compare struct clk pointers as a means of knowing
if the two pointers reference the same clock hardware. This behavior is
dubious (drivers must not dereference struct clk), but did not cause any
regressions until the per-user struct clk patch was merged. Now the test
for matching clk's will always fail with per-user struct clk's.

clk_is_match is introduced to fix the regression and prevent drivers
from comparing the pointers manually.

Fixes: 035a61c3 ("clk: Make clk API return per-user struct clk instances")
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>
[arnd@arndb.de: Fix COMMON_CLK=N && HAS_CLK=Y config]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[sboyd@codeaurora.org: const arguments to clk_is_match() and
remove unnecessary ternary operation]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
type T;
identifier f;
@@

static T f (...) { ... }

@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@

-EXPORT_SYMBOL_GPL(f);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Fixes: 035a61c3 "clk: Make clk API return per-user struct clk instances"
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>

Similar to the reasoning for the previous commit

	DIV_ROUND_CLOSEST(parent_rate, rate)

might not be the best integer divisor to get a good approximation for
rate from parent_rate (given the metric for CLK_DIVIDER_ROUND_CLOSEST).

For example assume a parent rate of 1000 Hz and a target rate of 700.
Using DIV_ROUND_CLOSEST the suggested divisor gets calculated to 1
resulting in a target rate of 1000 with a delta of 300 to the desired
rate. With choosing 2 as divisor however the resulting rate is 500 which
is nearer to 700.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

It's an invalid approach to assume that among two divider values
the one nearer the exact divider is the better one.

Assume a parent rate of 1000 Hz, a divider with CLK_DIVIDER_POWER_OF_TWO
and a target rate of 89 Hz. The exact divider is ~ 11.236 so 8 and 16
are the candidates to choose from yielding rates 125 Hz and 62.5 Hz
respectivly. While 8 is nearer to 11.236 than 16 is, the latter is still
the better divider as 62.5 is nearer to 89 than 125 is.

Fixes: 774b5143 (clk: divider: Add round to closest divider)
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

The rate provided at the output of a clk-divider is calculated as:

	DIV_ROUND_UP(parent_rate, div)

since commit b11d282d (clk: divider: fix rate calculation for
fractional rates). So to yield a rate not bigger than r parent_rate
must be <= r * div.

The effect of choosing a parent rate that is too big as was done before
this patch results in wrongly ruling out good dividers.

Note that this is not a complete fix as __clk_round_rate might return a
value >= its 2nd parameter. Also for dividers with
CLK_DIVIDER_ROUND_CLOSEST set the calculation is not accurate. But this
fixes the test case by Sascha Hauer that uses a chain of three dividers
under a fixed clock.

Fixes: b11d282d (clk: divider: fix rate calculation for fractional rates)
Suggested-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

Commit bca9690b ("clk: divider: Make generic for usage elsewhere")
returned only the divider value for read-only dividers instead of the
actual rate.

Fixes: bca9690b ("clk: divider: Make generic for usage elsewhere")
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Tested-by: NJames Hogan <james.hogan@imgtec.com>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

This commit adds a new clock driver for the Marvell Armada 39x family
of processors. This driver is fairly similar to the ones already used
on other Marvell EBU processors, with the following main differences:

 * Different set of ratios
 * Different set of core clocks
 * Configurable reference clock in frequency
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The Armada 39x, contrary to its predecessor, has a configurable
reference clock frequency, of either 25 Mhz, or 40 Mhz. For the
previous SoCs, it was fixed to 25 Mhz and described directly as such
in the Device Tree.

For Armada 39x, we need to read certain registers to know whether the
frequency is 25 or 40 Mhz. Therefore, this commit extends the common
mvebu clock code to allow the SoC-specific code to say it wants to
register a reference clock, by giving a non-NULL ->get_refclk_freq()
function pointer in its coreclk_soc_desc structure.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

With the introduction of the Marvell Armada 39x SoC, the DT bindings
for Marvell EBU clocks need to be extended. This commit include the
corresponding update to the Device Tree bindings documentation.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

drivers/clk/qcom/lcc-msm8960.c:577:3-8: No need to set .owner here. The core will do it.

 Remove .owner field if calls are used which set it automatically

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

drivers/clk/qcom/lcc-ipq806x.c:465:3-8: No need to set .owner here. The core will do it.

 Remove .owner field if calls are used which set it automatically

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci

CC: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

This clock is needed for most audio clock frequencies. Add it.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

regmap_read() returns 0 on success, not the value of the register
that is read. Fix it so we properly detect the frequency plan.

Fixes: b82875ee "clk: qcom: Add MSM8960/APQ8064 LPASS clock
controller (LCC) driver"
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

These shifts were copy/pasted from the pcm which is a different
size RCG. Use the correct offsets so that slimbus rates are
correct.

Fixes: b82875ee "clk: qcom: Add MSM8960/APQ8064 LPASS clock controller (LCC) driver"
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

Commit 163152cb ("clk: ti: Add support for FAPLL on dm816x")
added basic support for the FAPLL on dm818x, but has a bug for the
parent PLL enable bit. The FAPLL_MAIN_PLLEN is defined as BIT(3)
but the code is doing a shift on it.

This means the parent PLL won't get disabled even if all it's child
synthesizers are disabled.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMichael Turquette <mturquette@linaro.org>

.. after extensive statistical analysis of my G+ polling, I've come to
the inescapable conclusion that internet polls are bad.

Big surprise.

But "Hurr durr I'ma sheep" trounced "I like online polls" by a 62-to-38%
margin, in a poll that people weren't even supposed to participate in.
Who can argue with solid numbers like that? 5,796 votes from people who
can't even follow the most basic directions?

In contrast, "v4.0" beat out "v3.20" by a slimmer margin of 56-to-44%,
but with a total of 29,110 votes right now.

Now, arguably, that vote spread is only about 3,200 votes, which is less
than the almost six thousand votes that the "please ignore" poll got, so
it could be considered noise.

But hey, I asked, so I'll honor the votes.

Pull ext4 fixes from Ted Ts'o:
 "Ext4 bug fixes.

  We also reserved code points for encryption and read-only images (for
  which the implementation is mostly just the reserved code point for a
  read-only feature :-)"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix indirect punch hole corruption
  ext4: ignore journal checksum on remount; don't fail
  ext4: remove duplicate remount check for JOURNAL_CHECKSUM change
  ext4: fix mmap data corruption in nodelalloc mode when blocksize < pagesize
  ext4: support read-only images
  ext4: change to use setup_timer() instead of init_timer()
  ext4: reserve codepoints used by the ext4 encryption feature
  jbd2: complain about descriptor block checksum errors

Pull more vfs updates from Al Viro:
 "Assorted stuff from this cycle.  The big ones here are multilayer
  overlayfs from Miklos and beginning of sorting ->d_inode accesses out
  from David"

* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (51 commits)
  autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
  procfs: fix race between symlink removals and traversals
  debugfs: leave freeing a symlink body until inode eviction
  Documentation/filesystems/Locking: ->get_sb() is long gone
  trylock_super(): replacement for grab_super_passive()
  fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
  Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
  VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry)
  SELinux: Use d_is_positive() rather than testing dentry->d_inode
  Smack: Use d_is_positive() rather than testing dentry->d_inode
  TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR()
  Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode
  Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb
  VFS: Split DCACHE_FILE_TYPE into regular and special types
  VFS: Add a fallthrough flag for marking virtual dentries
  VFS: Add a whiteout dentry type
  VFS: Introduce inode-getting helpers for layered/unioned fs environments
  Infiniband: Fix potential NULL d_inode dereference
  posix_acl: fix reference leaks in posix_acl_create
  autofs4: Wrong format for printing dentry
  ...

Pull ARM fix from Russell King:
 "Just one fix this time around.  __iommu_alloc_buffer() can cause a
  BUG() if dma_alloc_coherent() is called with either __GFP_DMA32 or
  __GFP_HIGHMEM set.  The patch from Alexandre addresses this"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8305/1: DMA: Fix kzalloc flags in __iommu_alloc_buffer()

X-Coverup: just ask spender
Cc: stable@vger.kernel.org
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

use_pde()/unuse_pde() in ->follow_link()/->put_link() resp.

Cc: stable@vger.kernel.org
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

As it is, we have debugfs_remove() racing with symlink traversals.
Supply ->evict_inode() and do freeing there - inode will remain
pinned until we are done with the symlink body.

And rip the idiocy with checking if dentry is positive right after
we'd verified debugfs_positive(), which is a stronger check...

Cc: stable@vger.kernel.org
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>