Fix build error when CONFIG_MAGIC_SYSRQ is not enabled:

drivers/usb/serial/generic.c:566: error: implicit declaration of function 'handle_sysrq'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add ZIO Motherboard USB serial interface driver.
Signed-off-by: NVijay Kumar B. <vijaykumar@zilogic.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usb console code has had a long standing problem of not being able
to pass the baud rate from the kernel argument console=ttyUSB0,BAUD
down to the initial tty open, unless you were willing to settle for
9600 baud.

The solution is to directly use tty_init_termios() in
usb_console_setup() as this will preserve any changes to the initial
termios setting on future opens.

CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

"Static" buffers in fsg_buffhd structure (ie. fields which are arrays
rather then pointers to dynamically allocated memory) are not aligned
to any "big" power of two which may lead to poor DMA performance
(copying "by hand" of head or tail) or no DMA at all even if otherwise
hardware supports it.

Therefore, this patch makes mass storage function use kmalloc()ed
buffers which are (because of their size) page aligned (which should
be enough for any hardware).
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

... and simplify the was we read/write from/to
DMA COUNT register.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

we can support the musb-specific test modes on the
vendor specific range of test selector as stated
on USB Specification Table 9-7 Test Mode Selectors.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

for now only a simple register dump entry (which can
be rather useful on debugging) and a way to start
test modes.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Rather than hardcoding the gpio levels for vrsel, allow the platform
resources to handle this so boards can be active high or low.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds CONFIG_ARCH_OMAP4 macro within
MUSB driver.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch updates the Makefile to build the
MUSB driver for OMAP4. It also sets the Kconfig
options for OMAP4.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Program the OTG_INTERFSEL register based on
transcevier type passed from board file.

Adapt signature of musb_platform_init() function
for davinci, blackfin and tusb6010.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

boards might want to optimize their fifo configuration
to the particular needs of that specific board. Allow
that by moving all related data structures to
<linux/usb/musb.h>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace all instances of using the console variable in struct
usb_serial_port with the struct tty_port version.

CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I've been running variations of this patch for well over a year now;
my usual zoo of test devices didn't trigger any ill effects even
under heavy load.  As a nice sideeffect idle-wakeups are reduced
from 20/s to about 2/s (EHCI hub with mouse and kbd).
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1350) removes all usages of coherent buffers for USB
control-request setup-packet buffers.  There's no good reason to
reserve coherent memory for these things; control requests are hardly
ever used in large quantity (the major exception is firmware
transfers, and they aren't time-critical).  Furthermore, only seven
drivers used it.  We might as well always use streaming DMA mappings
for setup-packet buffers, and remove some extra complexity from
usbcore.

The DMA-mapping portion of hcd.c is currently in flux.  A separate
patch will be submitted to remove support for URB_NO_SETUP_DMA_MAP
after everything else settles down.  The removal should go smoothly,
as by then nobody will be using it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1349b) clears up the confusion in many USB host
controller drivers between port features and port statuses.  In mosty
cases it's true that the status bit is in the position given by the
corresponding feature value, but that's not always true and it's not
guaranteed in the USB spec.

There's no functional change, just replacing expressions of the form
(1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1348) removes the bogus
USB_PORT_FEAT_{HIGHSPEED,SUPERSPEED} symbols from ch11.h.  No such
features are defined by the USB spec.  (There is a PORT_LOWSPEED
feature, but the spec doesn't mention it except to say that host
software should never use it.)  The speed indicators are port
statuses, not port features.

As a temporary workaround for the xhci-hcd driver, a fictional
USB_PORT_STAT_SUPER_SPEED symbol is added.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove duplicated #include('s) in
  drivers/usb/core/hcd.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The compiler throws the following warning when compiling for a PowerPC 64
bit machine:

drivers/usb/storage/isd200.c:580: warning: the frame size of 2208 bytes is larger than 2048 bytes

There is a struct scsi_device which is placed on the stack and is
largely responsible for such wastage. The struct is just a dummy struct
filled with NULLs and set as the scsi_cmnd->device to make the
usb_stor_Bulk_transport function happy.

This patch makes the struct static, so that it is never placed onto the
stack and silences the compiler warning.
Signed-off-by: NIan Munsie <imunsie@au.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix usb/class sparse warnings:

drivers/usb/class/cdc-acm.h:128:34: error: dubious one-bit signed bitfield
drivers/usb/class/cdc-acm.h:129:24: error: dubious one-bit signed bitfield
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Seems to me that BKL is not needed here because necessary locking is already
provided by mutex sisusb->lock.

Also change the returned value to long.
Signed-off-by: NAlessio Igor Bogani <abogani@texware.it>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hub.h from drivers/usb/core into include/linux/usb/
Signed-of-by: NEric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: NEric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The length of the scatter gather list a driver can enqueue is limited by
the bus' sg_tablesize to 62 entries.  Each entry will be described by at
least one transfer request block (TRB).  If the entry's buffer crosses a
64KB boundary, then that entry will have to be described by two or more
TRBs.  So even if the USB device driver respects sg_tablesize, the whole
scatter list may take more than 62 TRBs to describe, and won't fit on
the ring.

Don't assume that an empty ring means there is enough room on the
transfer ring.  The old code would unconditionally queue this too-large
transfer, and over write the beginning of the transfer.  This would mean
the cycle bit was unchanged in those overwritten transfers, causing the
hardware to think it didn't own the TRBs, and the host would seem to
hang.

Now drivers may see submit_urb() fail with -ENOMEM if the transfers are
too big to fit on the ring.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a scatter-gather list is enqueued to the xHCI driver, it translates
each entry into a transfer request block (TRB).  Only 63 TRBs can be
used per ring segment, and there must be one additional TRB reserved to
make sure the hardware does not think the ring is empty (so the enqueue
pointer doesn't equal the dequeue pointer).  Limit the bus sg_tablesize
to 62 TRBs.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the USB core installs a new interface, it unconditionally clears the
halts on all the endpoints on the new interface.  Usually the xHCI host
needs to know when an endpoint is reset, so it can change its internal
endpoint state.  In this case, it doesn't care, because the endpoints were
never halted in the first place.

To avoid issuing a redundant Reset Endpoint command, the xHCI driver looks
at xhci_virt_ep->stopped_td to determine if the endpoint was actually
halted.  However, the functions that handle the stall never set that
variable to NULL after it dealt with the stall.  So if an endpoint stalled
and a Reset Endpoint command completed, and then the class driver tried to
install a new alternate setting, the xHCI driver would access the old
xhci_virt_ep->stopped_td pointer.  A similar problem occurs if the
endpoint has been stopped to cancel a transfer.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As we were using an internal dma flushing routine, this patch changes to
the DMA API flush_kernel_dcache_page().  Driver is able to compile now.

[akpm@linux-foundation.org: flush_kernel_dcache_page() comes before kunmap_atomic()]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

1) i_flags simply doesn't work for mount/unlink race prevention;
we may have many links to file and rm on one of those obviously
shouldn't prevent bind on top of another later on.  To fix it
right way we need to mark _dentry_ as unsuitable for mounting
upon; new flag (DCACHE_CANT_MOUNT) is protected by d_flags and
i_mutex on the inode in question.  Set it (with dont_mount(dentry))
in unlink/rmdir/etc., check (with cant_mount(dentry)) in places
in namespace.c that used to check for S_DEAD.  Setting S_DEAD
is still needed in places where we used to set it (for directories
getting killed), since we rely on it for readdir/rmdir race
prevention.

2) rename()/mount() protection has another bogosity - we unhash
the target before we'd checked that it's not a mountpoint.  Fixed.

3) ancient bogosity in pivot_root() - we locked i_mutex on the
right directory, but checked S_DEAD on the different (and wrong)
one.  Noticed and fixed.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The imx CTS trigger level is left at its reset value that is 32
chars. Since the RX FIFO has 32 entries, when CTS is raised, the
FIFO already is full. However, some serial port devices first empty
their TX FIFO before stopping when CTS is raised, resulting in lost
chars.

This patch sets the trigger level lower so that other chars arrive
after CTS is raised, there is still room for 16 of them.

Signed-off-by: Valentin Longchamp<valentin.longchamp@epfl.ch>
Tested-by: Philippe Rétornaz<philippe.retornaz@epfl.ch>
Acked-by: Wolfram Sang<w.sang@pengutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Arnd noted:

After the "retry_open:" label, we first get the tty_mutex
and then the BKL. However a the end of tty_open, we jump
back to retry_open with the BKL still held. If we run into
this case, the tty_open function will be left with the BKL
still held.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 6acc6833
introduced NULL pointer dereference and kernel crash
on ppc32 machines while booting. Fix this bug now.
Reported-by: NLeonardo Chiquitto <leonardo.lists@gmail.com>
Tested-by: NLeonardo Chiquitto <leonardo.lists@gmail.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In certain circumstances, especially under heavy load, the AUXADC
completion interrupt may be detected after we've timed out waiting for
it.  That conversion would still succeed but the next conversion will
see the completion that was signalled by the interrupt for the previous
conversion and therefore not wait for the AUXADC conversion to run,
causing it to report failure.

Provide a simple, non-invasive cleanup by using try_wait_for_completion()
to ensure that the completion is not signalled before we wait.  Since
the AUXADC is run within a mutex we know there can only have been at
most one AUXADC interrupt outstanding.  A more involved change should
follow for the next merge window.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

With dma based spi transmission, data corruption is observed
occasionally. With dma buffers located right next to msg and
xfer fields, cache lines correctly flushed in preparation for
dma usage may be polluted again when writing to fields in the
same cache line.

Make sure cache fields used with dma do not share cache lines
with fields changed during dma handling. As both fields are part
of a struct that is allocated via kzalloc, thus cache aligned,
moving the fields to the 1st position and insert padding for
alignment does the job.
Signed-off-by: NOskar Schirmer <os@emlix.com>
Signed-off-by: NDaniel Glöckner <dg@emlix.com>
Signed-off-by: NOliver Schneidewind <osw@emlix.com>
Signed-off-by: NJohannes Weiner <jw@emlix.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
[dtor@mail.ru - changed to use ___cacheline_aligned as suggested
 by akpm]
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Synaptics hardware requires resetting device after suspend to ram
in order for the device to be operational. The reset lives in
synaptics-specific reconnect handler, but it is not being invoked
if synaptics support is disabled and the device is handled as a
standard PS/2 device (bare or IntelliMouse protocol).

Let's add reset into generic reconnect handler as well.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Apparently all 3 bytes returned by ETP_FW_VERSION_QUERY are significant
and should be taken into account when matching hardware version/features.
Tested-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This reverts commit 977d17bb, because it
can cause problems with some devices not getting any resources at all
when the resource tree is re-allocated.

For an example of this, see

	https://bugzilla.kernel.org/show_bug.cgi?id=15960
	(originally https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4982)
	(lkml thread: http://lkml.org/lkml/2010/4/19/20)

where Peter Henriksson reported his Xonar DX sound card gone, because
the IO port region was no longer allocated.
Reported-bisected-and-tested-by: NPeter Henriksson <peter.henriksson@gmail.com>
Requested-by: NAndrew Morton <akpm@linux-foundation.org>
Requested-by: NClemens Ladisch <clemens@ladisch.de>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

According to memory-barriers.txt, an smp memory barrier in guest
should always be paired with an smp memory barrier in host,
and I quote "a lack of appropriate pairing is almost certainly an
error". In case of vhost, failure to flush out used index
update before looking at the interrupt disable flag
could result in missed interrupts, resulting in
networking hang under stress.

This might happen when flags read bypasses used index write.
So we see interrupts disabled and do not interrupt, at the
same time guest writes flags value to enable interrupt,
reads an old used index value, thinks that
used ring is empty and waits for interrupt.

Note: the barrier we pair with here is in
drivers/virtio/virtio_ring.c, function
vring_enable_cb.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NJuan Quintela <quintela@redhat.com>

This fixes the build failures seen when building mpcore_wdt and it
also removes the nonexistent ARM_MPCORE_PLATFORM dependency, instead
make it dependent on HAVE_ARM_TWD.

Also this fixes spinlock usage appropriately.
Signed-off-by: Nsrinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The various dasd_sleep_on functions use a global wait queue when
waiting for a cqr. The wait condition checks the status and devlist
fields of the cqr to determine if it is safe to continue. This
evaluation may return true, although the tasklet has not finished
processing of the cqr and the callback function has not been called
yet. When the callback is finally called, the data in the cqr may
already be invalid. The sleep_on wait condition needs a safe way to
determine if the tasklet has finished processing. Use the
callback_data field of the cqr to store a token, which is set by
the callback function itself.

Cc: <stable@kernel.org>
Signed-off-by: NStefan Weinhuber <wein@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

i915_error_object_create() is called from the timer interrupt and hence
can corrupt the KM_USER0 slot.  Use KM_IRQ0 instead.
Reported-by: NJaswinder Singh Rajput <jaswinderlinux@gmail.com>
Tested-by: NJaswinder Singh Rajput <jaswinderlinux@gmail.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>