Now that the bio list management stuff is generic, convert pktcdvd to
use bio lists instead of its own private bio list implementation.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NPeter Osterlund <petero2@telia.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from txdone routine.  So Unconditional call to the
netif_wake_queue() here is wrong.  This might cause calling of
start_xmit routine on txfull state and trigger BUG_ON.

This bug does not happen when NAPI disabled.  After txdone there
must be at least one free tx slot.  But with NAPI, this is not
true anymore and the BUG_ON can hits on heavy load.

In this driver NAPI was enabled on 2.6.33-rc1 so this is
regression from 2.6.32 kernel.
Reported-by: NRalf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new vid/pid to the cdc_ether whitelist.

Device added:
- Ericsson Mobile Broadband variant C3607w
Signed-off-by: NTorgny Johansson <torgny.johansson@gmail.com>

--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.htmlSigned-off-by: NDavid S. Miller <davem@davemloft.net>

Check for error return from pci_map_single/pci_map_page and clean up.

With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Intercept query commands and apply relocations to their guest pointers.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Commit 4410f391 ("fbdev: add support for
handoff from firmware to hw framebuffers") didn't add fb_destroy
operation to efifb.  Fix it and change aperture_size to match size
passed to request_mem_region.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15151Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Reported-by: NAlex Zhavnerchik <alex.vizor@gmail.com>
Tested-by: NAlex Zhavnerchik <alex.vizor@gmail.com>
Acked-by: NPeter Jones <pjones@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

geode-mfgpt: restore previous behavior for selecting IRQ

The MFGPT IRQ used to be, in order of decreasing priority,
 * IRQ supplied by the user as a boot-time parameter,
 * IRQ previously set by the BIOS or another driver,
 * default IRQ given at compile time.

Return to this behavior, which got broken when splitting the
MFGPT/clocksource driver for 2.6.33-rc1.
Signed-off-by: NJens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: NAndres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This also modifies the unused PRAMIN PT entries to be all zeroes, can't
really recall why I used 9/0 initially, just that it didn't work for
some reason.  It was likely masking a bug elsewhere that's since been
fixed.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

This commit changes nouveau to construct PTEs which look very much like
the ones the binary driver creates.

I presume that filling multiple PTEs identically with length flags and
the physical address of the start of a block of VRAM is a hint to the
memory controller that it need not perform additional page table lookups
for that range of addresses.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

GART is handled elsewhere, no reason to have the code for it here too.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

ACPI deep C-state entry had a long standing bug/missing feature, wherein we were sending
resched IPIs when an idle CPU is in mwait based deep C-state. Only mwait based C1 was using
the write to the monitored address to wake up mwait'ing CPU.

This patch changes the code to retain TS_POLLING bit if we are entering an mwait based
deep C-state.

The patch has been verified to reduce the number of resched IPIs in general and also
improves the performance/power on workloads with low system utilization (i.e., when mwait based
deep C-states are being used).

Fixes "netperf ~50% regression with 2.6.33-rc1, bisect to 1b9508f6"
http://marc.info/?l=linux-kernel&m=126441481427331&w=4Reported-by: NLin Ming <ming.m.lin@intel.com>
Tested-by: NAlex Shi <alex.shi@intel.com>
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Commit 84b79f8d (drm/i915: Fix crash
while aborting hibernation) attempted to fix a regression introduced
by commit cbda12d7 (drm/i915:
implement new pm ops for i915), but it went too far trying to split
the freeze/suspend and resume/thaw parts of the code.  As a result,
it introduced another regression, which only is visible on some systems.

Fix the problem by merging i915_drm_suspend() with
i915_drm_freeze() and moving some code from i915_resume()
into i915_drm_thaw(), so that intel_opregion_free() and
intel_opregion_init() are also executed in the freeze and thaw code
paths, respectively.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: NPedro Ribeiro <pedrib@gmail.com>
Tested-by: NTino Keitel <tino.keitel@tikei.de>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Check the frame control for ieee80211_is_data_qos() is true before
counting the number of tfds can be free, the tfds_in_queue only
increment when ieee80211_is_data_qos() is true before transmit; so it
should only decrement if the type match.

Remove ieee80211_is_data_qos check for frame_ctrl in tx_resp to avoid
invalid information pass from uCode.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When receive reply_tx and ready to decrement the count for number of
tfds in queue, do error checking to prevent error condition and
tfds_in_queue become negative number.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are several duplicate definitions in cciss_cmd.h and cciss_ioctl.h.
Consolidate these into the new cciss_defs.h file. This patch doesn't change
the definitions exposed under include/linux, so userspace apps shouldn't
be affected.
Acked-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Ndann frazier <dannf@hp.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Some cleanup before the header file split-out so we don't propagate this style
into new files.
Acked-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Ndann frazier <dannf@hp.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Generaltouch protocol allows for coordinates in [0, 0xffff] range and
there are devices reporting coordinates as high as 0x7fff so let's update
the driver to reflect that.
Signed-off-by: NRoy Yin <yhch@generaltouch.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Relying on overflow/wrap around isn't exact because if you wrap far
enough, you get back to "valid" values.
Reported-by: NThorsten Pohlmann <pohlmann@tetronik.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>

When polled input device is opened and closed and there are no other
users of polled device, the workqueue is created and destroyed in
every open / close operation. It is probable that at some point
dynamic allocation of internal parts of the workqueue cause changes to the
workqueue.

When a work is queued to the workqueue the work struct contains pointers
to the workqueue data. If the workqueue has been changed and the work
has never been queued to the new workqueue, work-struct contains pointers
to the non-existing workqueue. This will cause crash at the work
cancellation during device close since cancellation of a work assumes
that the workqueue exists.

To prevent that, work struct is cleaned up at device close. This keeps
work struct clean for the next use.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The temperature and voltage limits currently set on these boards are
too conservative and will cause the driver to stop the net device
erroneously in some systems.

Based on a review of the chip datasheets and advice from the designer
of these boards:

- Raise the maximum board temperatures to the specified maximum ambient
  temperatures for their PHYs plus the expected temperature bias of the
  board
- Raise the maximum controller temperature to 90 degrees
- Lower the minimum temperatures to 0 degrees
- Widen the voltage tolerances to at least +/- 10%
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

efx_mcdi_poll() uses positive error numbers, matching the MCDI
protocol.  It must negate the result of efx_mcdi_poll_reboot() which
returns the usual negative error numbers.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This lets UMS userspace know the rv740 fix is in. For KMS we can
consider the kernel release to be the v2.0.0 release so we don't need the
bump there.
Signed-off-by: NDave Airlie <airlied@redhat.com>

If at IB free time fence wasn't emited that means the IB wasn't
scheduled because an error occured somewhere, thus we can free
then fence and mark the IB as free.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

http://bugzilla.kernel.org/show_bug.cgi?id=15328

This fixes a serious regression on AGP/non-PAT systems, where
pages were ending up in the wrong state and slowing down the
whole system.

[airlied: taken this from the bug as the other option is to revert
the change which caused it].

Tested-by: John W. Linville (in bug).
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch fixes occlusion queries and rendering errors
on rv740 boards. Hardcoding the backend map is not an optimal
solution, but a better fix is being worked on.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Just compare the i2c id since the i2c structs
may be slighly different.

Fixes fdo bug 26616.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

rs600 board lists DVI port as HDMI.

Fixes fdo bug 26605
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Commit 77c1ff39 fixed the userspace
pointer dereference, but introduced another bug pointed out by Eugene Teo
in RH bug #564264. Instead of comparing the point we were at in the string,
we instead compared the beginning of the string to "default".
Signed-off-by: NKyle McMartin <kyle@redhat.com>
Reported-by: NEugene Teo <eteo@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It looks like this patch -

commit 7b2519af
Author: Yang, Bo <Bo.Yang@lsi.com>
Date:   Tue Oct 6 14:52:20 2009 -0600

    [SCSI] megaraid_sas: fix 64 bit sense pointer truncation

has caused a problem for 32bit programs with 64bit os -

http://bugzilla.kernel.org/show_bug.cgi?id=15001

fix by converting the user space 32bit pointer to a 64 bit one when
needed.

[jejb: fix up some 64 bit warnings]
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Cc: Bo Yang <Bo.Yang@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The HT extension channel settings require priv->staging_rxon.channel to be
accurate. However, iwl_set_rxon_ht was being called before iwl_set_rxon_channel
and thus HT40 could be broken unless another call to iwl_mac_config came in.

This problem was recently introduced by "iwlwifi: Fix to set correct ht
configuration"

The particular setting in which I noticed this was monitor mode:

	iwconfig wlan0 mode monitor
	ifconfig wlan0 up
	./iw wlan0 set channel 64 HT40-
	#./iw wlan0 set channel 64 HT40-
	tcpdump -i wlan0 -y IEEE802_11_RADIO

would only catch HT40 packets if I issued the IW command twice.

From visual inspection, iwl_set_rxon_channel does not depend on
iwl_set_rxon_ht, so simply swapping them should be safe and fixes this problem.
Signed-off-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Earlier, Ingo Molnar posted a patch to make it so that the kernel would avoid
reading _PPC on his broken T60.  Unfortunately, it seems that with Thomas
Renninger's patch last July to eliminate _PPC evaluations when the processor
driver loads, the kernel never actually reads _PPC at all!  This is problematic
if you happen to boot your non-T60 computer in a state where the BIOS _wants_
_PPC to be something other than zero.

So, put the _PPC evaluation back into acpi_processor_get_performance_info if
ignore_ppc isn't 1.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Set the backlight to use the current brightness when loaded, rather than
always resetting the backlight to maximum brightness.

Fixes kernel bugzilla #14207
Signed-off-by: NCarlos Corbacho <carlos@strangeworlds.co.uk>
Reported-by: NDenis Mukhin <denis_mukhin@yahoo.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Move I2C IR initialization from just after I2C bus setup to right
before non-I2C IR initialization. This avoids the case where an I2C IR
device is blocking audio support (at least the PV951 suffers from
this). It is also more logical to group IR support together,
regardless of the connectivity.

This fixes bug #15184:
http://bugzilla.kernel.org/show_bug.cgi?id=15184Signed-off-by: NJean Delvare <khali@linux-fr.org>
CC: stable@kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: Video : pwc : Fix regression in pwc_set_shutter_speed caused by bad 	constant => sizeof conversion.

Regression was caused by my commit 6b35ca0d
which determined message size using sizeof rather than hardcoded constants.

Unfortunately pwc_set_shutter_speed reuses a 2 byte buffer for a one byte
message too so the sizeof was bogus in this case.

All other uses of sizeof checked and are ok.
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This polling is needed if camera is in standby mode, but current exiting
condition is inverted.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cxusb uses the atbm8830 and lgs8gxx (not lgs8gl5) frontends and the
max2165 tuner, so it needs to select them.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I'm trying to fix it on the GCC side (PR43007), but the module is
quite stupid in using ULL constants to operate on u32 values:

static int apply_frontend_param (struct dvb_frontend* fe, struct
dvb_frontend_parameters *param)
{
...
 static const u32 ppm = 8000;
 u32 spi_bias;
...

 spi_bias *= 1000ULL;
 spi_bias /= 1000ULL + ppm/1000;

which causes current GCC 4.5 to emit calls to __udivdi3 for i?86 again.

This patch fixes this issue.
Signed-off-by: NRichard Guenther <rguenther@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
CC: stable@kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>