Per the PCI Firmware spec, r3.0, sec 4.5.1, on ACPI systems, the OS must
not use AER unless _OSC is present and _OSC grants AER control to the OS.
The aerdriver.forceload kernel parameter was a way to enable Linux AER
support on ACPI systems that lack _OSC or fail to grant control the the OS.

Enabling Linux AER support when the firmware doesn't want us to is a recipe
for problems, e.g., the firmware might be handling AER itself.

Remove the aerdriver.forceload kernel parameter and related supporting
code.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

The aerdriver.nosourceid kernel parameter was intended for working around
broken chipsets don't supply the source ID for AER events.  We recently
added PCI_BUS_FLAGS_NO_AERSID, which can be set by quirks for the same
purpose.

Remove the aerdriver.nosourceid kernel parameter.  For anything other than
debugging, asking users to find and use kernel parameters is a poor user
experience.  Instead, we should add PCI_BUS_FLAGS_NO_AERSID quirks for any
hardware that needs it.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

VMD root ports change all source ids to the VMD device ID.  To find the
sender of the AER notification, we need to scan all child devices for the
AER sender, rather than relying on the source ID from the message.
Signed-off-by: NJon Derrick <jonathan.derrick@intel.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Allow root port buses to choose to skip source id matching when finding the
faulting device.  Certain root port devices may return an incorrect source
ID and recommend to scan child device registers for AER notifications.
Signed-off-by: NJon Derrick <jonathan.derrick@intel.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

If a PCI bridge (or PCIe port) that is runtime-suspended gets an ACPI
hotplug notification, such as a bus check, it has to be resumed before
re-scanning the devices below it, or those devices will not be
accessible and will be treated as hot-removed.

Make that happen and let the bridge suspend again after the bus below it
has been re-scanned.

This is a replacement for commit 16468c78 ("ACPI / hotplug / PCI:
Runtime resume bridge before rescan") that has been reverted, because it
introduced a system resume regression (due to missing bridge->pci_dev
checks that are necessary in case the notification is targeted at the
host bridge) and it is necessary for the code added by commit
006d44e4 ("PCI: Add runtime PM support for PCIe ports") to work as
expected.
Tested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The use of config_enabled() against config options is ambiguous.  In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED().  Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc.  makes the intention
clearer.

This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.

I noticed two cases where config_enabled() is used against a tristate
option:

 - config_enabled(CONFIG_HWMON)
  [ drivers/net/wireless/ath/ath10k/thermal.c ]

 - config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
  [ drivers/gpu/drm/gma500/opregion.c ]

I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.

Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.comSigned-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NKees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit 16468c78.

Bisection showed that it was the root cause for a resume hang on a
bog-standard all-Intel laptop (Sony Vaio Pro 11), and reverting fixes
the hang.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There was only one use of __initdata_refok and __exit_refok

__init_refok was used 46 times against 82 for __ref.

Those definitions are obsolete since commit 312b1485 ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")

This patch removes the following compatibility definitions and replaces
them treewide.

/* compatibility defines */
#define __init_refok     __ref
#define __initdata_refok __refdata
#define __exit_refok     __ref

I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)

[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.beSigned-off-by: NFabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_XGENE
  drivers/pci/host/Kconfig:       bool "X-Gene PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

[bhelgaas: changelog]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: Tanmay Inamdar <tinamdar@apm.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_HOST_THUNDER_PEM
  drivers/pci/host/Kconfig:       bool "Cavium Thunder PCIe controller to off-chip devices"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: David Daney <david.daney@cavium.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_HOST_THUNDER_ECAM
  drivers/pci/host/Kconfig:       bool "Cavium Thunder ECAM controller to on-chip devices on pass-1.x silicon"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: David Daney <david.daney@cavium.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_TEGRA
  drivers/pci/host/Kconfig:       bool "NVIDIA Tegra PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-tegra@vger.kernel.org

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_RCAR_GEN2
  drivers/pci/host/Kconfig:       bool "Renesas R-Car Gen2 Internal PCI controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NPhil Edworthy <phil.edworthy@renesas.com>
CC: Valentine Barshak <valentine.barshak@cogentembedded.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_RCAR_GEN2_PCIE
  drivers/pci/host/Kconfig:       bool "Renesas R-Car PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NPhil Edworthy <phil.edworthy@renesas.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_MVEBU
  drivers/pci/host/Kconfig:       bool "Marvell EBU PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Jason Cooper <jason@lakedaemon.net>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_LAYERSCAPE
  drivers/pci/host/Kconfig:       bool "Freescale Layerscape PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: Minghuan Lian <minghuan.Lian@freescale.com>
CC: Mingkai Hu <mingkai.hu@freescale.com>
CC: Roy Zang <tie-fei.zang@freescale.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_KEYSTONE
  drivers/pci/host/Kconfig:       bool "TI Keystone PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Tested-By: NMurali Karicheri <m-karicheri2@ti.com>

This code is not being built as a module by anyone:

  host/Kconfig:config PCI_HISI
  host/Kconfig:    bool "HiSilicon Hip05 and Hip06 SoCs PCIe controllers"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: Zhou Wang <wangzhou1@hisilicon.com>
CC: Dacai Zhu <zhudacai@hisilicon.com>
CC: Gabriele Paoloni <gabriele.paoloni@huawei.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCI_HOST_GENERIC
  drivers/pci/host/Kconfig:       bool "Generic PCI host controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NWill Deacon <will.deacon@arm.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCIE_DW_PLAT
  drivers/pci/host/Kconfig:       bool "Platform bus based DesignWare PCIe Controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NJoao Pinto <jpinto@synopsys.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCIE_ARTPEC6
  drivers/pci/host/Kconfig:       bool "Axis ARTPEC-6 PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog, add "Author" comment]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: Niklas Cassel <niklas.cassel@axis.com>
CC: Jesper Nilsson <jesper.nilsson@axis.com>

This code is not being built as a module by anyone:

  drivers/pci/host/Kconfig:config PCIE_ARMADA_8K
  drivers/pci/host/Kconfig:       bool "Marvell Armada-8K PCIe controller"

Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.

Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.

Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

[bhelgaas: changelog]
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>

The DesignWare PCIe driver requires MSI support, so we get a warning for
the artpec6 glue driver if that is not enabled:

  warning: (PCIE_ARTPEC6) selects PCIE_DW which has unmet direct dependencies (PCI && PCI_MSI_IRQ_DOMAIN)

Add the same dependency that all other such drivers have.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NNiklas Cassel <niklas.cassel@axis.com>

The Solarflare SFC9220 apparently lacks an ACS capability, but does not
perform peer-to-peer between functions.  Add a quirk so we know about this
isolation.

[bhelgaas: changelog]
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Add a driver for the Aardvark PCIe controller used on the Marvell Armada
3700 ARM64 SoC.

Based on work done by Hezi Shahmoon <hezi.shahmoon@marvell.com> and Marcin
Wojtas <mw@semihalf.com>.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

The value that should be programmed into the PADS_REFCLK register varies
per SoC.  Fix the Tegra PCIe driver to program the correct values.  Future
SoCs will require different values in cfg0/1, so the two values are stored
separately in the per-SoC data structures.

For reference, the values are all documented in NV bug 1771116 comment 20.
The ASIC team has validated all these values, except for the Tegra20 value
which is simply left unchanged in this patch.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NThierry Reding <treding@nvidia.com>

tegra_pcie_phy_power_on() calls tegra_pcie_phy_enable() only for legacy
SoCs.  However, part of tegra_pcie_phy_enable() needs to happen in all
cases.  Move that code up one level into tegra_pcie_phy_power_on().

[bhelgaas: changelog]
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

pcibios_min_mem only exists on 32-bit ARM, so using it in pci-tegra.c
prevents the driver from being used on other arches.

In __pci_assign_resource(), we clip the available area based on
PCIBIOS_MIN_MEM.  On 32-bit ARM, this is pcibios_min_mem, with a default
value of 0x01000000.  For Tegra, we discover the space available for PCI
resource allocation from the device tree, and the lowest address that will
ever be available is 0x12000000 (on Tegra124).

The Tegra windows are always higher than the default pcibios_min_mem, so
the __pci_assign_resource() has no effect, so there's no need to adjust
pcibios_min_mem here.

[bhelgaas: changelog]
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Use the pci_remap_iospace() function provided by the PCI core, rather
than the 32-bit ARM-specific pci_ioremap_io().
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Most of the register definitions use lowercase hexadecimal values, with a
few exceptions using uppercase.  Convert the latter to be more in line with
the former.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

A user may hot add a switch requiring more than one bus to enumerate.  This
previously required a system reboot if BIOS did not sufficiently pad the
bus resource, which they frequently don't do.

Add a kernel parameter so a user can specify the minimum number of bus
numbers to reserve for a hotplug bridge's subordinate buses so rebooting
won't be necessary.

The default is 1, which is equivalent to previous behavior.
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Change the Downstream Port Containment config type from tristate to bool.

The driver doesn't automatically load based on any rules, so it needs to be
built-in in order to bind to devices it needs to drive.
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

PCIe port type values are not flags, so OR'ing them is not correct.
Previously the result was equivalent to PCIe Downstream Ports, so we were
missing binding to DPC-capable Root Ports.

Change the type to 'any' so we can bind to both port types.  While this
will cause the code to check Upstream Ports, the driver won't claim them
since they are not DPC-capable.
Reported-by: NAlexander Antonov <alexanderx.v.antonov@intel.com>
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: Mika Westerberg <mika.westerberg@linux.intel.com>

SR-IOV disabled from the host causes a memory leak.  pci-hyperv usually
first receives a PCI_EJECT notification and then proceeds to delete the
hpdev list entry in hv_eject_device_work().  Later in hv_msi_free() since
the device is no longer on the device list hpdev is NULL and hv_msi_free
returns without freeing int_desc as part of hv_int_desc_free().
Signed-off-by: NCathy Avery <cavery@redhat.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NJake Oshins <jakeo@microsoft.com>

In dra7xx_pcie_init_irq_domain(), the pattern used to check and return
error is:

   if (!var) {
      dev_err(...);
      return PTR_ERR(var);
   }

So the returned value in case of error is always 0, which means 'success'.
Change it to return -ENODEV instead.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NKishon Vijay Abraham I <kishon@ti.com>

In xilinx_pcie_init_irq_domain(), the pattern used to check and return
error is:

   if (!var) {
      dev_err(...);
      return PTR_ERR(var);
   }

So the returned value in case of error is always 0, which means 'success'.
Change it to return -ENODEV instead.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NSören Brinkmann <soren.brinkmann@xilinx.com>

Some PCIe devices take a long time to reach link up state after retrain.
Poll for link up status after retraining the link.  This is to make sure
the link is up before we access configuration space.

[bhelgaas: changelog]
Signed-off-by: NLey Foon Tan <lftan@altera.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Check the link status before retraining.  If the link is not up, don't
bother trying to retrain it.

[bhelgaas: split code move to separate patch, changelog]
Signed-off-by: NLey Foon Tan <lftan@altera.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Move cra_writel(), cra_readl(), and altera_pcie_link_is_up() so a future
patch can use them in altera_pcie_retrain().  No functional change
intended.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Set the affinity_mask in the PCI device before allocating vectors so that
the affinity can be propagated through the MSI descriptor structures to the
core IRQ code.  To facilitate this, new __pci_enable_msi_range() and
__pci_enable_msix_range() helpers are factored out of their not prefixed
variants which assigning the new IRQ affinity mask in the PCI device so
that the low-level interrupt code can perform the interrupt affinity
assignment and do node-local allocations.

A new PCI_IRQ_NOAFFINITY flag is added to pci_alloc_irq_vectors() so that
this function can also be used by drivers that don't wish to use the
automatic affinity assignment.

[bhelgaas: omit "else" after "return" consistently]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NAlexander Gordeev <agordeev@redhat.com>