Changing occurrences of variants of PCI-X and PCIe to the PCI-SIG
terms listed in the "Trademark and Logo Usage Guidelines".
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf

Patch is limited to drivers/pci/ and changes concern non-comment parts or
anything that might be visible to the user.
Signed-off-by: NStefan Assmann <sassmann@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Changing occurrences of variants of PCI-X and PCIe to the PCI-SIG
terms listed in the "Trademark and Logo Usage Guidelines".
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf

Patch is limited to drivers/pci/ and changes concern comments only.
Signed-off-by: NStefan Assmann <sassmann@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Remark update_res from __init to __devinit as it is called also
from __devinit functions.

This patch removes the following warning message:

  WARNING: vmlinux.o(.devinit.text+0x774a): Section mismatch
  in reference from the function pci_root_bus_res() to the
  function .init.text:update_res()
  The function __devinit pci_root_bus_res() references
  a function __init update_res().
  If update_res is only used by pci_root_bus_res then
  annotate update_res with a matching annotation.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Aristeu Sergio <arozansk@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: linux-pci@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Handle device specific timeout and use FLR.
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NDexuan Cui <dexuan.cui@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Handle device specific reset requirements (i.e. vendor reg for reset
along with appropriate timeout).
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NDexuan Cui <dexuan.cui@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add a new type of quirk for resetting devices at pci_dev_reset time.
This is necessary to handle device with nonstandard reset procedures,
especially useful for guest drivers.
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NDexuan Cui <dexuan.cui@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Prior to this patch, if pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, ...)
returns 0 for all dev, pci_cache_line_size ends up set to zero
(instead of pci_dfl_cache_line_size).

This patch ensures the pci_cache_line_size = pci_dfl_cache_line_size
setting in the above scenario.

This happens in case of a kvm-88 guest (where, consequently, the rtl8139
NIC failed to initialize).
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NCsaba Henk <csaba@gluster.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Having read the PM part of the PCIe 2.0 specification more carefully
I think that it was a mistake to restrict the wake-up enable
propagation to non-PCIe devices, because if we do not request
control of the root ports' PME registers via OSC, PCIe PME is
supposed to be handled by the platform, just like the non-PCIe PME.
Even if we do that, the wake-up propagation is done to allow the
devices to wake up the system from sleep states which involves the
platform anyway, so it won't hurt.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

I detected a typo, while reading "Documentation/vgaarbiter.txt".  Fix the
'fieldd' mispelling.
Signed-off-by: NDetlef Riekenberg <wine.dev@web.de>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Caused by commit 0b83ddeb ("MFD:
twl4030: add twl4030_codec MFD as a new child to the core") interacting
with commit b07682b6 ("mfd: Rename
twl4030* driver files to enable re-use").

This file seems to have been missed in the renaming.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: event tracing support
  xfs: change the xfs_iext_insert / xfs_iext_remove
  xfs: cleanup bmap extent state macros

* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (80 commits)
  dm snapshot: use merge origin if snapshot invalid
  dm snapshot: report merge failure in status
  dm snapshot: merge consecutive chunks together
  dm snapshot: trigger exceptions in remaining snapshots during merge
  dm snapshot: delay merging a chunk until writes to it complete
  dm snapshot: queue writes to chunks being merged
  dm snapshot: add merging
  dm snapshot: permit only one merge at once
  dm snapshot: support barriers in snapshot merge target
  dm snapshot: avoid allocating exceptions in merge
  dm snapshot: rework writing to origin
  dm snapshot: add merge target
  dm exception store: add merge specific methods
  dm snapshot: create function for chunk_is_tracked wait
  dm snapshot: make bio optional in __origin_write
  dm mpath: reject messages when device is suspended
  dm: export suspended state to targets
  dm: rename dm_suspended to dm_suspended_md
  dm: swap target postsuspend call and setting suspended flag
  dm crypt: add plain64 iv
  ...

* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block:
  cfq: set workload as expired if it doesn't have any slice left
  Fix a CFQ crash in "for-2.6.33" branch of block tree
  cfq: Remove wait_request flag when idle time is being deleted
  cfq-iosched: commenting non-obvious initialization
  cfq-iosched: Take care of corner cases of group losing share due to deletion
  cfq-iosched: Get rid of cfqq wait_busy_done flag
  cfq: Optimization for close cooperating queue searching
  block,xd: Delay allocation of DMA buffers until device is known
  drbd: Following the hmac change to SHASH (see linux commit 8bd1209c)
  cfq-iosched: reduce write depth only if sync was delayed

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: ac97_codec - increase timeout for analog sections to 5 second
  ASoC: Correct code taking the size of a pointer
  ALSA: hda - Add PCI IDs for Nvidia G2xx-series
  ALSA: sound/isa/gus: Correct code taking the size of a pointer
  ALSA: hda: Fix max PCM level to 0 dB for AD1981_HP
  ALSA: hda: Use ALC260_WILL quirk for another Acer model (0x1025007f)

Merge branch 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (26 commits)
  clockevents: Convert to raw_spinlock
  clockevents: Make tick_device_lock static
  debugobjects: Convert to raw_spinlocks
  perf_event: Convert to raw_spinlock
  hrtimers: Convert to raw_spinlocks
  genirq: Convert irq_desc.lock to raw_spinlock
  smp: Convert smplocks to raw_spinlocks
  rtmutes: Convert rtmutex.lock to raw_spinlock
  sched: Convert pi_lock to raw_spinlock
  sched: Convert cpupri lock to raw_spinlock
  sched: Convert rt_runtime_lock to raw_spinlock
  sched: Convert rq->lock to raw_spinlock
  plist: Make plist debugging raw_spinlock aware
  bkl: Fixup core_lock fallout
  locking: Cleanup the name space completely
  locking: Further name space cleanups
  alpha: Fix fallout from locking changes
  locking: Implement new raw_spinlock
  locking: Convert raw_rwlock functions to arch_rwlock
  locking: Convert raw_rwlock to arch_rwlock
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: update default configurations for ATNGW100, ATSTK1002 and ATSTK1006
  avr32: add default configurations for ATNGW100 mkII and EVKLCD10X
  avr32: add support for ATNGW100 mkII board
  avr32: convert to asm-generic/hardirq.h
  avr32: add two new at91 to cpu.h definition
  avr32: clean up linker script using standard macros.
  avr32: MRMT: correct setup of SPI slaves
  avr32: function for independently setting up SPI slaves
  avr32: re-instate MCI WP/CD pin assignments for ATNGW100

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix clock event multiplier printf format.
  sparc64: Use clock{source,events}_calc_mult_shift().
  sparc64: Use free_bootmem_late() in mdesc_lmb_free().
  sparc: Add alignment and emulation fault perf events.
  sparc64: Add syscall tracepoint support.
  sparc: Stop trying to be so fancy and use __builtin_{memcpy,memset}()
  sparc: Use __builtin_object_size() to validate the buffer size for copy_from_user()
  sparc64: Add some missing __kprobes annotations to kernel fault paths.
  sparc64: Use kprobes_built_in() to avoid ifdefs in fault_64.c
  sparc: Validate that kprobe address is 4-byte aligned.
  sparc64: Don't specify IRQF_SHARED for LDC interrupts.
  sparc64: Fix stack debugging IRQ stack regression.
  sparc64: Fix overly strict range type matching for PCI devices.

* git://git.infradead.org/battery-2.6:
  power_supply_sysfs: Handle -ENODATA in a special way
  wm831x_backup: Remove unused variables
  gta02: Set pcf50633 charger_reference_current_ma
  pcf50633: Query charger status directly
  pcf50633: Properly reenable charging when the supply conditions change
  pcf50633: Get rid of charging restart software auto-triggering
  pcf50633: introduces battery charging current control
  pcf50633: Add ac power supply class to the charger
  wm831x: Factor out WM831x backup battery charger

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: Close usb_find_interface race v3
  Revert "USB: Close usb_find_interface race"

[akpm@linux-foundation.org: s/q/g/ (Randy)]
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NÉric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Report output values as 1/1000 of earth gravity.

Output values from lis3 can be read from sysfs position entry and from
input device.  Input device can be accessed as event device and as
joystick device.  Joystick device can be in two modes.  Meaning of the
output values varies from case to case depending on the chip type and
configuration (scale).  Only joystick interface in JS_CORR_BROKEN mode
returned somehow similar output values in different configurations.
Joystick device is in that state by default in case of lis3.

Position sysfs entry, input event device and raw joystick device have been
little bit broken since meaning of the output values has been varied
between 12 and 8 bit devices.  Applications which relayed on those methods
failed if the chip is different than the expected one.

This patch converts output values to mean similar thing in different
configurations.  Both 8 and 12 bit devices reports now same acceleration
values.  If somebody implements full scale support to the driver, output
values will still mean the same.  Scaling factor and input device range
must be updated in that case.

Joystick interface in JS_CORR_BROKEN mode is not touched by this patch.
All other interfaces have different scale after this change.  For 12 bit
device scaling factor is 0.977 which keeps scaled and unscaled values are
quite close to each others.  For 8 bit device, scaled values are 18 times
bigger than unscaled values.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NÉric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It is possible to read position information at the chip measurement rate
via sysfs.  This patch adds possibility to configure chip measurement
rate.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: NÉric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Chip is calibrated by the manufacturer.  There is no need to calibarate it
at driver level.  If the chip is used as a joystick, calibaration can be
done using joystick device calibration mechanism.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NÉric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implement selftest feature as specified by chip manufacturer.  Control:
read selftest sysfs entry

Response: "OK x y z" or "FAIL x y z"

where x, y, and z are difference between selftest mode and normal mode.
Test is passed when values are within acceptance limit values.

Acceptance limits are provided via platform data.  See chip spesifications
for acceptance limits.  If limits are not properly set, OK / FAIL decision
is meaningless.  However, userspace application can still make decision
based on the numeric x, y, z values.

Selftest is meant for HW diagnostic purposes.  It is not meant to be
called during normal use of the chip.  It may cause false interrupt
events.  Selftest mode delays polling of the normal results but it doesn't
cause wrong values.  Chip must be in static state during selftest.  Any
acceration during the test causes most probably failure.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NÉric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Lis3 accelerometer sensors have quite long power on delay (up to 125
ms). This patch adds necessary delay to power on sequence for currently
supported lis3 chips.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: NÉric Piel <eric.piel@tremplin-utc.net>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Originally the driver was only targeted to 12bits sensors.  When support
for 8bits sensors was added, some slight difference in the registers were
overlooked.  This should fix it, both for initialization, and for
displaying the rate.
Reported-by: NKalhan Trisal <kalhan.trisal@intel.com>
Reported-by: NChristoph Plattner <christoph.plattner@gmx.at>
Tested-by: NChristoph Plattner <christoph.plattner@gmx.at>
Tested-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Most of the documentation and comments were written when the driver was
only supporting one type of chip, only via ACPI/HP. Update the info to
the much clearer understanding that we have now.
Signed-off-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

polled input device itself was not free'd.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: NÉric Piel <eric.piel@tremplin-utc.net>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Send input_sync after each measurement round. This helps userspace to
detect which reported values belongs to the same measurement.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: NÉric Piel <eric.piel@tremplin-utc.net>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add control of fan minimum turn-on output levels, decoupling it from the
fan turn-off output level.  Add control of rate of change of fan output
level.  These in turn allow lower turn-off rotor speed and smoother
transitions for better thermal and acoustic control authority.  Add
support for constant fan speed and proportional-response operations modes.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NDaniel J Blueman <daniel.blueman@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Hubbard <david.c.hubbard@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add the possibility to remap axes via platform data.  Function pointers
for resource setup and release purposes
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jean Delvare <khali@linux-fr.org>
Cc:  "Trisal, Kalhan" <kalhan.trisal@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move common crc body to new function crc32_body() cleaup and micro
optimize crc32_body for speed and less size.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Improve the /proc/interrupts output so the irq number can be mapped to
platform device on boards with multiple tmio_mmc instances.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Cc: <linux-mmc@vger.kernel.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add SD host driver for Blackfin BF54x and BF51x.

[akpm@linux-foundation.org: fix layout, c99 warning]
Signed-off-by: NCliff Cai <cliffcai.sh@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This new revision of the IP adds some improvements to the MCI already
present in several Atmel SOC.

Some new registers are added and a particular way of handling DMA
interaction lead to a new sequence in function call which is backward
compatible: On MCI2, we must set the DMAEN bit to enable the DMA
handshaking interface.  This must happen before the data transfer command
is sent.

A new function is able to differentiate MCI2 code and is based on
knowledge of processor id (cpu_is_xxx()).
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow the use of another DMA controller driver in atmel-mci sd/mmc driver.
 This adds a generic dma_slave pointer to the mci platform structure where
we can store DMA controller information.  In atmel-mci we use information
provided by this structure to initialize the driver (with new helper
functions that are architecture dependant).

This also adds at32/avr32 chip modifications to cope with this new access
method.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some people run general-purpose distribution kernels on netbooks with
a card that is physically non-removable or logically non-removable
(e.g. used for /home) and cannot be cleanly unmounted during suspend.
Add a module parameter to set whether cards are assumed removable or
non-removable, with the default set by CONFIG_MMC_UNSAFE_RESUME.

In general, it is not possible to tell whether a card present in an MMC
slot after resume is the same that was there before suspend.  So there are
two possible behaviours, each of which will cause data loss in some cases:

CONFIG_MMC_UNSAFE_RESUME=n (default): Cards are assumed to be removed
during suspend.  Any filesystem on them must be unmounted before suspend;
otherwise, buffered writes will be lost.

CONFIG_MMC_UNSAFE_RESUME=y: Cards are assumed to remain present during
suspend.  They must not be swapped during suspend; otherwise, buffered
writes will be flushed to the wrong card.

Currently the choice is made at compile time and this allows that to be
overridden at module load time.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: Wouter van Heyst <larstiq@larstiq.dyndns.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert two missed s3c2410 specific gpio calls to gpiolib calls.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is still in use especially to develop SDIO device drivers on laptop
machines which are lacking SDIO slots.  This adapter supports SDIO cards
only due to lack of 136-bit response capability.
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove check for host->iclk being NULL from error path since we already
know it is non-null and use return value from clk_get.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>