RFC4301 Section 7.1 says:

"7.1.  Tunnel Mode SAs that Carry Initial and Non-Initial Fragments

     All implementations MUST support tunnel mode SAs that are configured
     to pass traffic without regard to port field (or ICMP type/code or
     Mobility Header type) values.  If the SA will carry traffic for
     specified protocols, the selector set for the SA MUST specify the
     port fields (or ICMP type/code or Mobility Header type) as ANY.  An
     SA defined in this fashion will carry all traffic including initial
     and non-initial fragments for the indicated Local/Remote addresses
     and specified Next Layer protocol(s)."

But for IPv6, fragment is treated as a protocol.  This change catches
protocol transported in fragmented packet.  In IPv4, there is no
problem.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One parameter wasn't described and one I forgot to update when
renaming it; also update TBDs in sta_info.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It was being discussed where we would put this, but now it found a home
so use its define.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_hw_keyreset returns true in either branch.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If card is using downloadable firmware (like Agere 9.x), firmware has
to be reloaded during resume. It is not possible to use request_firmware
for that, because tasks are still frozen, so request_firmware will
just timeout and fail. So cache firmware image in memory for later
reuse in ->resume method.
Signed-off-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On resume card state is likely lost so we have to reload firmware
again.
Signed-off-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Acked-by: NDavid Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

*Properly get/set all available ISR/IMR values and review common/uncommon bits
*Better handling of per-txq interrupts (we can now resolve what q is generating
 each interrupt -this will help in debuging wme later)
*Some minor updates from legacy-hal
*Properly handle RXNOFRM and TXNOFRM interrupt masking (even when we don't set
 them on IMR they keep showing up, so we disable them by zeroing AR5K_RXNOFRM
 and AR5K_TXNOFRM registers). This doesn't exist on legacy-hal but i've tested
 it on various cards and it works fine.

Changes-Licensed-under: ISC
Signed-Off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This function is only used once, move it closer to its caller.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This function has a few WARNs that may eventually trigger
when an AP sends rogue beacons, those must be removed. Some
of the comments in the function are also inappropriate as
this function is concerned with the global hint, not a per-
wiphy thing (which a multidomain flag on a wiphy would imply).

I'm convinced that we don't need to do anything to implement
multi-domain capability as 802.11-2007 specifies it because
it makes only two things mandatory:
 * starting of BSS/IBSS must have country information
   (this can easily be done with a mac80211 patch)
 * a STA must adopt the country information (we already have
   the framework for this)

But we don't have anything implemented anyway for now.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code needs to be split out and cleaned up, so as a
first step remove the capability, to add it back in a
subsequent patch as a separate function. Also remove the
publically facing return value of the function and the
wiphy argument. A number of internal functions go from
being generic helpers to just being used for alpha2
setting.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The regdom struct is given to the core, so it might as well
free it in error conditions.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The reclaim flag should include REPLY_RX_MPDU_CMD in the list of commands
issued by uCode. This is for safety in case the SEQ_RX_FRAME bit is set
incorrectly.
Signed-off-by: NDaniel Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The problem fixed here is that iwl3945_mac_get_tsf() returns 0, as the
function is not implemented, and this is considered as a valid value by
the mac layer in mlme.c:1605. The consequence is that the STA in ad-hoc
mode is inserted/removed quite frequently due to IBSS merging.

This patch fixes :
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1781
and https://bugzilla.redhat.com/show_bug.cgi?id=459401Signed-off-by: NFabrice Bellet <fabrice@bellet.info>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch drops unreadable usage of IWL_SET/GET_BITS16 in byte count
tables handling
This patch also cleans a bit the byte count table code and adds
WARN_ON traps on invalid values

This patch is pure cleanup, no functional changes.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver does not properly convert rate_n_flags to PLCP index for mimo3
packets. This makes mac80211 drop the packets
Signed-off-by: NDaniel C. Halperin <daniel.c.halperin@intel.com>
Reviewed-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since calibration framework is not HW specific remove 5000 and 4965 prefix
This patch doesn't provide any functional changes only code renaming
and movement
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch uses new parameters eeprom_ver and eeprom_calib_ver
to support additional HW.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch makes sure that station table is not accessed
with invalid station id in 4965 TX response path
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch utilize 5000 new TX response command
which contains all necessary information and avoids
back referencing to the original TX frame.
It also change handling of software queue tracking
4965 flow is aligned with changes as much as possible.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reviewed-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wireless HW without any dedicated queues for aggregation
do not need the ampdu_queues mechanism present right now
in mac80211. Since mac80211 is still incomplete wrt TX MQ
changes, do not allow aggregation sessions for drivers that
set ampdu_queues.

This is only an interim hack until Intel fixes the requeue issue.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NLuis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Eliminate the vif.type check in ieee80211_rx_h_action.  This check is
unnecessary (these action frames can be handled by all interface types) and
currently prevents, for example, AP interfaces from handling BACK action frames
such as ADDBA and DELBA requests.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A warning would be printed for every packet that
is transmitted if the rate control information isn't
setup. Change this to WARN_ON_ONCE.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were also changing tx power even when we were not asked to,
this enforces the change only when we are asked nicely. When
not asked we simply try to use the max power, we don't tx power
at all for rate control.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enables hardware interrupt mitigation on RX.
It should alleviate system interrupt load intelligently.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sc_txintrperiod is currently set to 0 and never updated. We won't
be using this, if anything we will consider using TX interrupt
mitigation but that is different and not yet tested. So remove
sc_txintrperiod and the pointless spin_lock_bh() on tx prepare.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We do not know what max power to allow until a device is targeting
a channel, therefore only allow changing tx power if a channel is defined.
Also make use of the channel's max power setting as defined by
regulatory rules before allowing the user to use the requested power
setting. If the user asked us to figure it out we use the max allowed
by regulatory.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch add a check on the return value of dev_alloc_skb() in
ieee80211_sta_join_ibss() in net/mac80211/mlme.c.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is quite a lot of overlap in definitions between these headers...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also change escape_ssid to print_ssid to match print_mac semantics.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also use common backslash sequences like \t, \n, \r, and \\ as well as \0.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is unnecessary and of questionable value.  Also remove
is_empty_ssid, as it is also unnecessary.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We never clearly defined the semantics of the sta_notify callback
and it was originally posted for iwlwifi which still doesn't use
it at all. With the recent HT rework ath9k started relying on it,
but I made a mistake there in that I made ath9k assume the HT
information has already been filled in at sta_notify time. This
isn't a hard thing to do, so do it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

debugfs_create_*() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: NZhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

debugfs_create_bool() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: NZhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

http://en.wikipedia.org/wiki/De_Morgan%27s_laws is useful.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>