Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Convert to module_i2c_driver() too.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Redundant, the device is only a CODEC.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This allows userspace control of final power off, allowing policy decisions
for register configuration retention.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Only enable and disable the FLL when explicitly told to, supporting some
additional use cases and making the driver behaviour more standard.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

No longer needed with regmap.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise we might not have a sensible clocking setup ready.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Make sure we update for any changes in cases where we reconfigure while
live (eg, for analogue bypass).
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Machine kcontrols now use card instead of codec for thier "chip".
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Show the id we read when the id mismatch is detected.
This is useful for debugging.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow platform widgets to be visible in debugfs like codec widgets.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since the addition of the non-CODEC control adds card controls like the
DAPM pin switch have been broken as they are expecting the private data
for the control to be the CODEC but it's now the card. Fix that for the
pin switches, an audit of other drivers is required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Update the codec debugfs initialisation to use dev_warn() instead of
printk(KERN_WARNING).
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Currently when DAPM widgets are power sequenced the stream_event()
completion callback is only called for the stream_event originator
DAPM context. Other components in the card may also be interested so
make sure they are also notified of any widget power events.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It's useful to export the DAPM reset as a static function for future use
by other DAPM functions. e.g. The dynamic PCM query widgets resets the DAPM
graph before working out active paths.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Improves performance on power up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The main role of the WM9081 is as a class D speaker amplifier so there
is no concern about pops. There are also very few registers and a fast
power up time so we can happily mark the driver as idle_bias_off.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Better style and better supports idle_bias_off which we're going to
implement.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

ALC5632 codec supports digital microphone. This patch adds DAPM widget.
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure we're in a known state when we restart.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Raise the ramp time to 50ms to cover corner cases, use the startup bias
generator, explicitly reset the ramp circuit when complete and reorder
things all of which should improve performance somewhat for systems that
are sensitive to noise from VMID.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reduces the amount of time taken to stabilise them.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The enable of the single ended line outputs on wm_hubs devices performs
better if the output is enabled prior to starting VMID. Since inactive
outputs are held at VMID anyway there is little cost to doing this for
unused outputs. Add callbacks into wm_hubs and keep track of which outputs
are really active so we can disable them once we're active.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to the mixer path diagram input sources' attenuators logically
belong to the playback path and DMIC boost only affects capture.
Signed-off-by: NPaul Fertser <fercerpav@gmail.com>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This brings the TLVs in sync with the documentation and allows to properly
manipulate mic boost controls with alsamixer.
Signed-off-by: NPaul Fertser <fercerpav@gmail.com>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch should fix output through speakers using HP mixer.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix I2S digital interface power for recording.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add DMIC switches and controls to ALC5632 codec.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Refactored DAPM routes to add voice support.

- Added undocumented register
- Used AIF in/out
- Added missed voice items and routes
- Added DMIC input
- Romoved unrelevant items
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There is no Phone Mix<->Mono Mix route in datasheet.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Rename capture switches to common scheme XXX2REC.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add voice DAC playback switch.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Remove extra zero from volume step in DECLARE_TLV_DB_SCALE macro.
Signed-off-by: NAndrey Danin <danindrey@mail.ru>
Signed-off-by: NLeon Romanovsky <leon@leon.nu>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>