The hw cursor is relatively adept at triggering underflows, which
manifest as a "blue flash" (since blue is configured as the underflow
color).  Juggle a few things around to tighten up the timing for setting
cursor registers in DONE irq.

And most importantly, don't ever disable the hw cursor.  Instead flip it
to a blank/empty cursor.  This seems far more reliable, as even simply
clearing the cursor-enable bit (with no other updates in previous/
following frames) can in some cases cause underflow.

v1: original
v2: add missing locking spotted by Micah

Cc: Micah Richert <richert@braincorporation.com>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Since X11 is going to create an XR24 fb, if the pixel formats do not
match then crtc helpers will think it is a full modeset even if mode is
the same, which prevents smooth/flickerless handover from fbcon/plymouth
to X11.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Signed-off-by: NMicah Richert <richert@braincorporation.com>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC.  Replace all references to the CRTC fb with the
primary plane's fb.

This patch was generated by the Coccinelle semantic patching tool using
the following rules:

        @@ struct drm_crtc C; @@
        -   (C).fb
        +   C.primary->fb

        @@ struct drm_crtc *C; @@
        -   (C)->fb
        +   C->primary->fb

v3: Generate patch via coccinelle.  Actual removal of crtc->fb has been
    moved to a subsequent patch.

v2: Fixup several lingering crtc->fb instances that were missed in the
    first patch iteration.  [Rob Clark]
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NRob Clark <robdclark@gmail.com>

Use drm_universal_plane_init() and drm_crtc_init_with_planes() rather
than the legacy drm_plane_init() / drm_crtc_init().  This will ensure
that the proper primary plane is registered with the DRM (and eventually
exposed to userspace in future patches).

Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NRob Clark <robdclark@gmail.com>

Make things recover a bit more gracefully if we get stuck with no vblank
irq ever coming.
Signed-off-by: NRob Clark <robdclark@gmail.com>

After reading a nice article on LWN[1], I went back and double checked
my handling of invalid-input checking.  Turns out there were a couple
places I had missed.

Since the driver is fairly young, and the devices it supports are really
only just barely usable for basic stuff (serial console) with an
upstream kernel, I think we should fix this now and revert specific
parts of this patch later in the unlikely event that a regression is
reported.

[1] https://lwn.net/Articles/588444/Signed-off-by: NRob Clark <robdclark@gmail.com>

Signed-off-by: NRob Clark <robdclark@gmail.com>

Some of the w/a or different behavior of userspace blob driver seem to
be keyed to gpu patch revision, rather than gpu-id.  So expose the full
chip-id to userspace so it can DTRT.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Shut down the clks when the gpu has nothing to do.  A short inactivity
timer is used to provide a low pass filter for power transitions.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Helper macro to simplify places where we need to poll with timeout
waiting for gpu.
Signed-off-by: NRob Clark <robdclark@gmail.com>

msm.hang_debug=y will dump out current register values if the gpu locks
up, for easier debugging.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Signed-off-by: NRob Clark <robdclark@gmail.com>

The ARCH_MSM depend is redundant with ARCH_MSM8960, so we can remove it.
Additionally, we are splitting Qualcomm MSM support into legacy (ARCH_MSM)
and multiplatform (ARCH_QCOM).  The MSM8960 with be ARCH_QCOM going forward
so dropping ARCH_MSM will work properly for the new ARCH_QCOM multiplatform
build.
Acked-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Because we use a list_head in the bo to track it's position in a submit,
we need to serialize at a higher layer.  Otherwise there are problems
when multiple contexts are SUBMIT'ing in parallel cmdstreams referencing
a shared bo.
Signed-off-by: NRob Clark <robdclark@gmail.com>

We already hold struct_mutex here.
Signed-off-by: NRob Clark <robdclark@gmail.com>

It seems we need to update all cursor registers from vblank.  This
appears to be the cause of intermittent underflows when enabling/
disabling cursor.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Backport a few fixes found in the course of getting mdp5 working.
There is a window of time after pageflip is requested, before we
start scanning out the new fb (ie. while we are waiting for gpu).
During that time we need to continue holding a reference to the
still-current scanout fb, to avoid the backing gem bo's from being
destroyed.

Possibly a common mdp_crtc parent class could be useful to share
some of this logic between mdp4_crtc and mdp5_crtc.  OTOH, this
all can be removed from the driver once atomic is in place, as
plane/crtc updates get deferred until all fb's are ready before
calling in to .page_flip(), etc.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Signed-off-by: NRob Clark <robdclark@gmail.com>

Small typo I noticed in the mdp4_plane code.. no consequence because
PIPE_SRC_XY and PIPE_DST_XY have same register layout.
Signed-off-by: NRob Clark <robdclark@gmail.com>

This was hidden in a generic void * dev->mm_private. But only ever
used for gem. But thanks to this fake generic pretension no one
noticed that Rob's drm drivers are now all broken.

So just give the offset manager a type pointer and fix up msm, omapdrm
and tilcdc.

v2: Fixup compile fail.

v3: Fixup rebase fail that David spotted.

Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Add support for adreno 330.  Not too much different, just a few
differences in initial configuration plus setting OCMEM base.
Userspace support is already in upstream mesa.

Note that the existing DT code is simply using the bindings from
downstream android kernel, to simplify porting of this driver to
existing devices.  These do not constitute any committed/stable
DT ABI.  The addition of proper DT bindings will be a subsequent
patch, at which point (as best as possible) I will try to support
either upstream bindings or what is found in downstream android
kernel, so that existing device DT files can be used.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Add support for the new MDP5 display controller block.  The mapping
between parts of the display controller and KMS is:

  plane   -> PIPE{RGBn,VIGn}             \
  crtc    -> LM (layer mixer)            |-> MDP "device"
  encoder -> INTF                        /
  connector -> HDMI/DSI/eDP/etc          --> other device(s)

Unlike MDP4, it appears we can get by with a single encoder, rather
than needing a different implementation for DTV, DSI, etc.  (Ie. the
register interface is same, just different bases.)

Also unlike MDP4, all the IRQs for other blocks (HDMI, DSI, etc) are
routed through MDP.

And finally, MDP5 has this "Shared Memory Pool" (called "SMP"), from
which blocks need to be allocated to the active pipes based on fetch
stride.
Signed-off-by: NRob Clark <robdclark@gmail.com>

The HDMI block is basically the same between older SoC's with mdp4
display controller, and newer ones with mdp5.

So mostly this consists of better abstracting out the different sets of
regulators, clks, etc.  In particular, for regulators and clks we can
split it up by what is needed for hot plug detect to work, and what is
needed to light up the display.

Also, 8x74 has a new phy.. a very simple one, but split out into a
different mmio space.  And with mdp5, the irq is shared with mdp, so we
don't directly register our own irq handler.
Signed-off-by: NRob Clark <robdclark@gmail.com>

We'll want basically the same thing for mdp5, so refactor it out so it
can be shared.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Signed-off-by: NRob Clark <robdclark@gmail.com>

This can be shared between mdp4 and mdp5.  Both use the same set of
parameters to describe the format to the hw.
Signed-off-by: NRob Clark <robdclark@gmail.com>

resync to latest envytools db, add mdp5 registers
Signed-off-by: NRob Clark <robdclark@gmail.com>

There are some little bits and pieces that mdp4 and mdp5 can share, so
move things around so that we can have both in a common parent
directory.
Signed-off-by: NRob Clark <robdclark@gmail.com>

This adds the necessary configuration for the APQ8060A SoC (dual-core
krait + a320 gpu) as found on the bstem board.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Add a VRAM carveout that is used for systems which do not have an IOMMU.

The VRAM carveout uses CMA.  The arch code must setup a CMA pool for the
device (preferrably in highmem.. a 256m-512m VRAM pool in lowmem is not
cool).  The user can configure the VRAM pool size using msm.vram module
param.

Technically, the abstraction of IOMMU behind msm_mmu is not strictly
needed, but it simplifies the GEM code a bit, and will be useful later
when I add support for a2xx devices with GPUMMU, so I decided to keep
this part.

It appears to be possible to configure the GPU to restrict access to
addresses within the VRAM pool, but this is not done yet.  So for now
the GPU will refuse to load if there is no sort of mmu.  Once address
based limits are supported and tested to confirm that we aren't giving
the GPU access to arbitrary memory, this restriction can be lifted
Signed-off-by: NRob Clark <robdclark@gmail.com>

This got a bit broken with original patches when re-arranging things to
move dependencies on mach-msm inside #ifndef OF.
Signed-off-by: NRob Clark <robdclark@gmail.com>

Signed-off-by: NRob Clark <robdclark@gmail.com>

With a simple stub, we can get COMPILE_TEST support.
Signed-off-by: NRob Clark <robdclark@gmail.com>

The DRM driver for MSM depends on symbols from the MSM
IOMMU driver. Add this dependency to the Kconfig file.

Fixes this comile error:

  Kernel: arch/arm/boot/zImage is ready
  ERROR: "msm_iommu_get_ctx" [drivers/gpu/drm/msm/msm.ko]
  undefined!
  make[2]: *** [__modpost] Error 1

Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: NJoerg Roedel <joro@8bytes.org>

I've killed them a long time ago in drm/i915, let's get rid of this
remnant of shared drm core days for good.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The drvdata pointer is already assigned to something useful.

Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

There were a few potential problems with the original page_flip/vblank
code in mdp4_crtc.

1) We need vblank irq for a couple things, both completing flips and
   updating cursor.  We need to keep track of what work is pending so
   that (for example) a cursor update while we are still waiting for
   pageflip_cb (ie. pageflip requested from userspace, but still
   waiting for rendering to complete) would not prematurely trigger
   event to userspace.

2) A preclose -> pageflip-cancel should not cancel a pageflip that
   was requested on a different file (ie. non-master closing should
   not cancel a pending pageflip).

With these fixes, we no longer have problems w/ cursor not updating and
with occasional hangs with userspace waiting for a pageflip that had
been cancelled (launching XBMC from gnome-shell overview mode was a good
way to trigger this, but now works reliably).
Signed-off-by: NRob Clark <robdclark@gmail.com>

Subsequent threads returning EBUSY from vm_insert_pfn() was not
handled correctly. As a result concurrent access from new threads
to mmapped data caused SIGBUS.

See e79e0fe3Signed-off-by: NRob Clark <robdclark@gmail.com>
Acked-by: NDavid Brown <davidb@codeaurora.org>

Re-arrange things a bit so that we can get work requested after a bo
fence passes, like pageflip, done before retiring bo's.  Without any
sort of bo cache in userspace, some games can trigger hundred's of
transient bo's, which can cause retire to take a long time (5-10ms).
Obviously we want a bo cache.. but this cleanup will make things a
bit easier for atomic as well and makes things a bit cleaner.
Signed-off-by: NRob Clark <robdclark@gmail.com>
Acked-by: NDavid Brown <davidb@codeaurora.org>