Daniel Borkmann says:

====================
Couple of minor improvements to the x64 JIT I had still around from
pre merge window in order to shrink the image size further. Added
test cases for kselftests too as well as running Cilium workloads on
them w/o issues.
====================
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Add few test cases that check the rnu-time results under JIT.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

While it's rather cumbersome to reduce prologue for cBPF->eBPF
migrations wrt spill/fill for r15 which is callee saved register
due to bpf_error path in bpf_jit.S that is both used by migrations
as well as native eBPF, we can still trivially save 5 bytes in
prologue for the former since tail calls can never be used there.
cBPF->eBPF migrations also have their own custom prologue in BPF
asm that xors A and X reg anyway, so it's fine we skip this here.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Add a generic emit_mov_reg() helper in order to reuse it in BPF
multiplication to load the src into rax, we can save a few bytes
in alu32 while doing so.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Instead of unconditionally performing push/pop on rax/rdx
in case of multiplication, we can save a few bytes in case
of dest register being either BPF r0 (rax) or r3 (rdx)
since the result is written in there anyway.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

While analyzing some of the more complex BPF programs from Cilium,
I found that LLVM generally prefers to emit LD_IMM64 instead of MOV32
BPF instructions for loading unsigned 32-bit immediates into a
register. Given we cannot change the current/stable LLVM versions
that are already out there, lets optimize this case such that the
JIT prefers to emit 'mov %eax, imm32' over 'movabsq %rax, imm64'
whenever suitable in order to reduce the image size by 4-5 bytes per
such load in the typical case, reducing image size on some of the
bigger programs by up to 4%. emit_mov_imm32() and emit_mov_imm64()
have been added as helpers.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

When we shift by one, we can use a different encoding where imm
is not explicitly needed, which saves 1 byte per such op.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

sk is already allocated in inet_create/inet6_create, hence when
BPF_CGROUP_RUN_PROG_INET_SOCK is executed sk will never be NULL.

The logic is as bellow,
	sk = sk_alloc();
	if (!sk)
		goto out;
	BPF_CGROUP_RUN_PROG_INET_SOCK(sk);
Signed-off-by: NYafang Shao <laoar.shao@gmail.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Joe Stringer says:

====================
This is series makes some minor changes primarily focused on making it easier
to understand why test_verifier is failing a test. This includes printing the
observed output when a test fails in a different way than expected, or when
unprivileged tests fail due to sysctl kernel.unprivileged_bpf_disabled=1. The
last patch removes some apparently dead code.
====================
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

This array appears to be completely unused, remove it.
Signed-off-by: NJoe Stringer <joe@wand.net.nz>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

The "kernel.unprivileged_bpf_disabled" sysctl, if enabled, causes all
unprivileged tests to fail because it permanently disables unprivileged
BPF access for the currently running kernel. Skip the relevant tests if
the user attempts to run the testsuite with this sysctl enabled.
Signed-off-by: NJoe Stringer <joe@wand.net.nz>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

When priviliged tests are skipped due to user rights, count the number of
skipped tests so it's more obvious that the test did not check everything.
Signed-off-by: NJoe Stringer <joe@wand.net.nz>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

This makes it easier to debug off-hand when the error message isn't
exactly as expected.
Signed-off-by: NJoe Stringer <joe@wand.net.nz>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

The default rlimit RLIMIT_MEMLOCK is 64KB. In certain cases,
e.g. in a test machine mimicking our production system, this test may
fail due to unable to charge the required memory for map creation:
   # ./test_tcpbpf_user
   libbpf: failed to create map (name: 'global_map'): Operation not permitted
   libbpf: failed to load object 'test_tcpbpf_kern.o'
   FAILED: load_bpf_file failed for: test_tcpbpf_kern.o

Changing the default rlimit RLIMIT_MEMLOCK to unlimited makes
the test always pass.
Signed-off-by: NYonghong Song <yhs@fb.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

The current selftests Makefile construct result in cgroup_helpers.c
gets compiled together with all the TEST_GEN_PROGS. And it also result
in invoking the libbpf Makefile two times (tools/lib/bpf).

These issues were introduced in commit 9d1f1594 ("bpf: move
cgroup_helpers from samples/bpf/ to tools/testing/selftesting/bpf/").

The only test program that requires the cgroup helpers is 'test_dev_cgroup'.

Thus, create a make target $(OUTPUT)/test_dev_cgroup that extend[1]
the 'prerequisite' for the 'stem' %-style pattern in ../lib.mk,
for this particular test program.

Reviewers notice the make-rules in tools/testing/selftests/lib.mk
differ from the normal kernel kbuild rules, and it is practical
to use 'make -p' to follow how these 'Implicit/static pattern stem'
gets expanded.

[1] https://www.gnu.org/software/make/manual/html_node/Static-Usage.html

Fixes: 9d1f1594 ("bpf: move cgroup_helpers from samples/bpf/ to tools/testing/selftesting/bpf/")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

If is sufficient with a forward declaration of struct xdp_rxq_info in
linux/filter.h, which avoids including net/xdp.h.  This was originally
suggested by John Fastabend during the review phase, but wasn't
included in the final patchset revision.  Thus, this followup.
Suggested-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

samples/sockops program keeps the sock_ops program attached to cgroup.
Fixed this by detaching program before exit.
Signed-off-by: NPrashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

While building samples/sockmap, undefined reference error is thrown
for `nla_dump_errormsg'.
Linking tools/lib/bpf/nlattr.o as a fix
Signed-off-by: NPrashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Default rlimit RLIMIT_MEMLOCK is 64KB, causes bpf map failure.
e.g.
[root@labbpf]# ./xdp_redirect $(</sys/class/net/eth2/ifindex) \
> $(</sys/class/net/eth3/ifindex)
failed to create a map: 1 Operation not permitted

The failure is seen when executing xdp_redirect while xdp_monitor
is already runnig.
Signed-off-by: NTushar Dave <tushar.n.dave@oracle.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Add test cases verifying FIB onlink commands work as expected in
various conditions - IPv4, IPv6, main table, and VRF.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Ahern says:

====================
selftests: fib_tests: simplifications, verbosity and a race

Improve efficiency of fib_tests.sh and make the test result more verbose,
from this summary:
$ fib_tests.sh is failing in a VM:
    $ fib_tests.sh
    Running netdev unregister tests
    PASS: unicast route test
    PASS: multipath route test
    Running netdev down tests
    PASS: unicast route test
    PASS: multipath route test
    Running netdev carrier change tests
    PASS: local route carrier test
    FAIL: unicast route carrier test

where a single entry actually corresponds to many checks to a much more
verbse output that clarifies test cases:
$fib_tests.sh
Single path route carrier test
    ....
    Carrier down
        IPv4 fibmatch                                         [ OK ]
        IPv6 fibmatch                                         [ OK ]
        IPv4 linkdown flag set                                [FAIL]
        IPv6 linkdown flag set                                [FAIL]
    Second address added with carrier down
        IPv4 fibmatch                                         [ OK ]
        IPv6 fibmatch                                         [ OK ]
        IPv4 linkdown flag set                                [FAIL]
        IPv6 linkdown flag set                                [ OK ]

And then fix the race in changing carrier down on dummy device to checking
the corresponding routes.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sleep for a second after setting carrier down to allow linkwatch
to propagate the change to the routing stack via netdev_state_change.
As it stands there is a race setting carrier down on the dummy
device and then checking the linkdown flag in the routes.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move setup and teardown of testns and dummy0 to helpers.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fib_tests.sh is failing in a VM:
    $ fib_tests.sh
    Running netdev unregister tests
    PASS: unicast route test
    PASS: multipath route test
    Running netdev down tests
    PASS: unicast route test
    PASS: multipath route test
    Running netdev carrier change tests
    PASS: local route carrier test
    FAIL: unicast route carrier test

The last test corresponds to fib_carrier_unicast_test which 12 places
that could be failing. Be more verbose in the output so a failure is
easier to track down and separate test setup failures with set -e and
set +e pairs.

With the verbose logging it is easier to see which checks are failing:
    $fib_tests.sh
    Single path route carrier test
        ....
        Carrier down
            IPv4 fibmatch                                         [ OK ]
            IPv6 fibmatch                                         [ OK ]
            IPv4 linkdown flag set                                [FAIL]
            IPv6 linkdown flag set                                [FAIL]
        Second address added with carrier down
            IPv4 fibmatch                                         [ OK ]
            IPv6 fibmatch                                         [ OK ]
            IPv4 linkdown flag set                                [FAIL]
            IPv6 linkdown flag set                                [ OK ]
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'ip netns exec testns ip' is more efficiently handled using 'ip -netns';
runs the ip command after switching the namespace and avoids an exec.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not export fib_multipath_hash or fib_select_path; both are only used
by core ipv4 code.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If flow oif is set and it is not an l3mdev, then fib_select_path
can jump to the source address check.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: rename sctp diag file and add file comments for it

This patchset is to remove the sctp_ prefix for sctp diag file,
and also to add the missing file comments for it.

v1->v2:
  split them into two patches as Marcelo suggested.
====================
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to add the missing file comments for sctp diag file.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove 'sctp_' prefix for diag file, to keep consistent with other
files' names.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use NL_SET_ERR_MSG_MOD helper which adds the module name instead
of specifying the prefix each time.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: SPAN cleanups

In patch one of this short series, a misplaced pointer star is moved to
the correct place.

In the second patch, we observe that if SPAN entries carry their
reference count anyway, it's redundant to also carry a "used" flag.

In the third patch, SPAN support code is moved to a separate module.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the upcoming work on SPAN, it makes sense to move the current code
to a module of its own. It already has a well-defined API boundary to
the mirror management (which is used from matchall and ACL code). A
couple more functions need to be exported for the functions that
spectrum.c needs to use for MTU handling and subsystem init/fini.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The member ref_count already determines whether a given SPAN entry is
used, and is as easy to use as a dedicated boolean.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: IPIP cleanups

In the first patch, a forgotten #include is added. Even though the code
compiles as-is, the include is necessary for modules that should include
spectrum_ipip.h.

The second patch corrects an assumption that IPv6 tunnels use struct
ip_tunnel_parm to store tunnel parameters.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct ip_tunnel_parm, where GRE and several other tunnel types hold
information, is IPv4-specific. The current router / ipip code in mlxsw
however uses it as if it were generic.

Make it clear that it's not. Rename many functions from _params_ to
_params4_. mlxsw_sp_ipip_parms_saddr() and _daddr() take a proto
argument to dispatch on it. Move the dispatch logic to
mlxsw_sp_ipip_netdev_saddr() and _daddr(), and replace with
single-protocol functions.

In struct mlxsw_sp_ipip_entry, move the "parms" field to a (for the time
being, singleton) union. Update users throughout.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct ip_tunnel_parm, which is used in spectrum_ipip.h, is defined in
if_tunnel.h. However, the former neglects to include the latter.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The comment stated that a thread was started, but
that is not the case.
Signed-off-by: NJake Moroni <mail@jakemoroni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kirill Tkhai says:

====================
Replacing net_mutex with rw_semaphore

this is the third version of the patchset introducing net_sem
instead of net_mutex. The patchset adds net_sem in addition
to net_mutex and allows pernet_operations to be "async". This
flag means, the pernet_operations methods are safe to be
executed with any other pernet_operations (un)initializing
another net.

If there are only async pernet_operations in the system,
net_mutex is not used either for setup_net() or for cleanup_net().

The pernet_operations converted in this patchset allow
to create minimal .config to have network working, and
the changes improve the performance like you may see
below:

    %for i in {1..10000}; do unshare -n bash -c exit; done

    *before*
    real 1m40,377s
    user 0m9,672s
    sys 0m19,928s

    *after*
    real 0m17,007s
    user 0m5,311s
    sys 0m11,779

    (5.8 times faster)

In the future, when all pernet_operations become async,
we'll just remove this "async" field tree-wide.

All the new logic is concentrated in patches [1-5/32].
The rest of patches converts specific operations:
review, rationale of they can be converted, and setting
of async flag.

Kirill

v3: Improved patches descriptions. Added comment into [5/32].
Added [32/32] converting netlink_tap_net_ops (new pernet operations
introduced in 2018).

v2: Single patch -> patchset with rationale of every conversion
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>