The flow spec coming in for IPv4 filters is IP_USER_FLOW, which
needed some more info to be communicated up above in order for it
to be displayed correctly.

Change-ID: Ia968238e0d7c4c4df12908ba81f0c4501280f3ec
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the FW workaround to increment the number of msix vectors.
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e to 0.3.41 and i40evf to 0.9.20.

Change-ID: If49251a1a81a0f25e8f74bc8b7d086befb6df676
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement the net device op for Tx bandwidth setting. Setting the Tx
bandwidth is done by 'ip link set <PF device> vf <VF num> rate <Tx
rate>', with the rate specified in Mbit/sec. The rate setting is
displayed with 'ip link show'.

Change-ID: I4d45dda8320632fdb6ec92c87d083e51070b46ab
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If a host VMM administrator hoses his VF by assigning a port VLAN after
it is already up and running with implicit permission to set local
VLANs then we print a message warning the host administrator that the
VF driver needs to be reloaded.

In addition we need to knock the VF offline so that it does not continue
to receive traffic not on the port VLAN assigned to it.  So we reset the
VF.  The VF will cease operation and the administrator will be forced to
unload and reload the VF driver to make it work again.

Change-ID: Iae1ae006b244e74e30a4ee546b3c5fca5cfb40aa
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PREFENA field in the receive host memory cache (RX-HMC)
must be visible in order to be set to 1 at driver init for
best performance.

Change-ID: I16b0bcd84cf56f4b6c938201ff5e954bee5a1992
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the netdev ops to support addition of static FDB entries in the
physical function (PF)  MAC/VLAN filter table so that virtual functions
(VFs) can communicate with bridged virtual Ethernet ports such as those
provided by the virtio driver.

Change-ID: Ifbd6817a75074e3b5cdf945a5635f26440bf15df
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Florian Fainelli says:

====================
net: ndo_set_config/ifmap cleanups

This patch series removes a bunch of useless ndo_set_config in non
PCMCIA Ethernet drivers.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

stmmac_config() denies changing the base address and interrupt
parameters, and ignores any other settings from the ifmap parameters,
thus making stmmac_config() useless, remove it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sxgbe_config() denies changing the base address and interrupt, and
ignores all other 'struct ifmap' members, which means that it is useless
as is, so let's remove it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cpmac_config() refuses changing the base address parameter, and ignores
all other parameters, which means that it is pretty useless as it is, so
let's remove it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethoc_config() returns -ENOSYS and does not implement anything useful,
let's remove it such that net/core/dev_ioctl.c::dev_ifsioc can return
something meaningful like -EOPNOTSUPP.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This feature allows multiple channels to be used by each virtual NIC.
It is available on Hyper-V host 2012 R2.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make tcp_cwnd_application_limited() static and move it from tcp_input.c to
tcp_output.c
Signed-off-by: NWeiping Pan <wpan@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't rely on driver files or other headers having this file included.

CC: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: linux-zigbee-devel@lists.sourceforge.net
Signed-off-by: NLuis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: linux-zigbee-devel@lists.sourceforge.net
Signed-off-by: NLuis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will simplify the new reassembly backport
with no code changes being required.

CC: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: linux-zigbee-devel@lists.sourceforge.net
Cc: David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NLuis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The busy polling socket option adds support for sockets to busy wait on data
arriving on the napi queue from which they have most recently received a frame.
Currently only tcp and udp support this feature, but theres no reason sctp can't
do so as well.  Add it in so appliations can take advantage of it
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Daniel Borkmann <dborkman@redhat.com>
CC: netdev@vger.kernel.org
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Acked-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make local functions static, because these are used only in this
file.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NByungho An <bh74.an@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently broadcasts are handled in network RX context, where
the packets are sent through netif_rx.  This means that the number
of macvlans will be constrained by the capacity of netif_rx.

For example, setting up 4096 macvlans practically causes all
broadcast packets to be dropped as the default netif_rx queue
size simply can't handle 4096 skbs being stuffed into it all
at once.

Fundamentally, we need to ensure that the amount of work handled
in each netif_rx backlog run is constrained.  As broadcasts are
anything but constrained, it either needs to be limited per run
or moved to process context.

This patch picks the second option and moves all broadcast handling
bar the trivial case of packets going to a single interface into
a work queue.  Obviously there also needs to be a limit on how
many broadcast packets we postpone in this way.  I've arbitrarily
chosen tx_queue_len of the master device as the limit (act_mirred
also happens to use this parameter in a similar way).

In order to ensure we don't exceed the backlog queue we will use
netif_rx_ni instead of netif_rx for broadcast packets.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Thanks,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the helper __dev_forward_skb which is identical to
dev_forward_skb except that it doesn't actually inject the skb into
the stack.  This is useful where we wish to have finer control over
how the packet is injected, e.g., via netif_rx_ni or netif_receive_skb.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a TCP_FASTOPEN socket option to get a max backlog on its
listener to getsockopt().
Signed-off-by: NKenjiro Nakayama <nakayamakenjiro@gmail.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the generic bits from genphy_config_init() instead of implementing
the same functionality again.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables other drivers to call this generic implementation, and then
only do specific details on top of it.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull x86 fix from Ingo Molnar:
 "This fixes the preemption-count imbalance crash reported by Owen
  Kibel"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce: Fix CMCI preemption bugs

Pull scheduler fixes from Ingo Molnar:
 "Two fixes:

   - a SCHED_DEADLINE task selection fix
   - a sched/numa related lockdep splat fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Check for stop task appearance when balancing happens
  sched/numa: Fix task_numa_free() lockdep splat

Pull perf fixes from Ingo Molnar:
 "Two kernel side fixes:

   - an Intel uncore PMU driver potential crash fix
   - a kprobes/perf-call-graph interaction fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Use rdmsrl_safe() when initializing RAPL PMU
  kprobes/x86: Fix page-fault handling logic

Pull drm fixes from Dave Airlie:
 "Unfortunately this contains no easter eggs, its a bit larger than I'd
  like, but I included a patch that just moves code from one file to
  another and I'd like to avoid merge conflicts with that later, so it
  makes it seem worse than it is,

  Otherwise:
   - radeon: fixes to use new microcode to stabilise some cards, use
     some common displayport code, some runtime pm fixes, pll regression
     fixes
   - i915: fix for some context oopses, a warn in a used path, backlight
     fixes
   - nouveau: regression fix
   - omap: a bunch of fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (51 commits)
  drm: bochs: drop unused struct fields
  drm: bochs: add power management support
  drm: cirrus: add power management support
  drm: Split out drm_probe_helper.c from drm_crtc_helper.c
  drm/plane-helper: Don't fake-implement primary plane disabling
  drm/ast: fix value check in cbr_scan2
  drm/nouveau/bios: fix a bit shift error introduced by 457e77b2
  drm/radeon/ci: make sure mc ucode is loaded before checking the size
  drm/radeon/si: make sure mc ucode is loaded before checking the size
  drm/radeon: improve PLL params if we don't match exactly v2
  drm/radeon: memory leak on bo reservation failure. v2
  drm/radeon: fix VCE fence command
  drm/radeon: re-enable mclk dpm on R7 260X asics
  drm/radeon: add support for newer mc ucode on CI (v2)
  drm/radeon: add support for newer mc ucode on SI (v2)
  drm/radeon: apply more strict limits for PLL params v2
  drm/radeon: update CI DPM powertune settings
  drm/radeon: fix runpm handling on APUs (v4)
  drm/radeon: disable mclk dpm on R7 260X
  drm/tegra: Remove gratuitous pad field
  ...

Some i2c fixes over DisplayPort.

* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
  drm/radeon: Improve vramlimit module param documentation
  drm/radeon: fix audio pin counts for DCE6+ (v2)
  drm/radeon/dp: switch to the common i2c over aux code
  drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
  drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
  drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
  drm/i915: support address only i2c-over-aux transactions
  drm/tegra: dp: Support address-only I2C-over-AUX transactions

Pull more networking fixes from David Miller:

 1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
    context, not synchronize it.  From Chris Mason.

 2) Ipv4 flow input interface should never be zero, it should be
    LOOPBACK_IFINDEX instead.  From Cong Wang and Julian Anastasov.

 3) Properly configure MAC to PHY connection in mvneta devices, from
    Thomas Petazzoni.

 4) sys_recv should use SYSCALL_DEFINE.  From Jan Glauber.

 5) Tunnel driver ioctls do not use the correct namespace, fix from
    Nicolas Dichtel.

 6) Fix memory leak on seccomp filter attach, from Kees Cook.

 7) Fix lockdep warning for nested vlans, from Ding Tianhong.

 8) Crashes can happen in SCTP due to how the auth_enable value is
    managed, fix from Vlad Yasevich.

 9) Wireless fixes from John W Linville and co.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
  net: sctp: cache auth_enable per endpoint
  tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
  vlan: Fix lockdep warning when vlan dev handle notification
  seccomp: fix memory leak on filter attach
  isdn: icn: buffer overflow in icn_command()
  ip6_tunnel: use the right netns in ioctl handler
  sit: use the right netns in ioctl handler
  ip_tunnel: use the right netns in ioctl handler
  net: use SYSCALL_DEFINEx for sys_recv
  net: mdio-gpio: Add support for separate MDI and MDO gpio pins
  net: mdio-gpio: Add support for active low gpio pins
  net: mdio-gpio: Use devm_ functions where possible
  ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
  ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
  mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
  net: mvneta: properly configure the MAC <-> PHY connection in all situations
  net: phy: add minimal support for QSGMII PHY
  sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
  mwifiex: fix hung task on command timeout
  mwifiex: process event before command response
  ...

Pull cifs fixes from Steve French:
 "A set of 5 small cifs fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cif: fix dead code
  cifs: fix error handling cifs_user_readv
  fs: cifs: remove unused variable.
  Return correct error on query of xattr on file with empty xattrs
  cifs: Wait for writebacks to complete before attempting write.

Pull char/misc driver fixes from Greg KH:
 "Here are a few driver fixes for char/misc drivers that resolve
  reported issues.

  All have been in linux-next successfully for a few days"

* tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Drivers: hv: vmbus: Negotiate version 3.0 when running on ws2012r2 hosts
  Tools: hv: Handle the case when the target file exists correctly
  vme_tsi148: Utilize to_pci_dev() macro
  vme_tsi148: Fix PCI address mapping assumption
  vme_tsi148: Fix typo in tsi148_slave_get()
  w1: avoid recursive device_add
  w1: fix netlink refcnt leak on error path
  misc: Grammar s/addition/additional/
  drivers: mcb: fix memory leak in chameleon_parse_cells() error path
  mei: ignore client writing state during cb completion
  mei: me: do not load the driver if the FW doesn't support MEI interface
  GenWQE: Increase driver version number
  GenWQE: Fix multithreading problems
  GenWQE: Ensure rc is not returning an uninitialized value
  GenWQE: Add wmb before DDCB is started
  GenWQE: Enable access to VPD flash area

Merge tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Here are some driver core fixes for 3.15-rc2.  Also in here are some
  documentation updates, as well as an API removal that had to wait for
  after -rc1 due to the cleanups coming into you from multiple developer
  trees (this one and the PPC tree.)

  All have been in linux next successfully"

* tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  drivers/base/dd.c incorrect pr_debug() parameters
  Documentation: Update stable address in Chinese and Japanese translations
  topology: Fix compilation warning when not in SMP
  Chinese: add translation of io_ordering.txt
  stable_kernel_rules: spelling/word usage
  sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()
  kernfs: protect lazy kernfs_iattrs allocation with mutex
  fs: Don't return 0 from get_anon_bdev

Pull staging driver fixes from Greg KH:
 "Here are a few staging driver fixes for issues that have been reported
  for 3.15-rc2.

  Also dominating the diffstat for the pull request is the removal of
  the rtl8187se driver.  It's no longer needed in staging as a "real"
  driver for this hardware is now merged in the tree in the "correct"
  location in drivers/net/

  All of these patches have been tested in linux-next"

* tag 'staging-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: r8188eu: Fix case where ethtype was never obtained and always be checked against 0
  staging: r8712u: Fix case where ethtype was never obtained and always be checked against 0
  staging: r8188eu: Calling rtw_get_stainfo() with a NULL sta_addr will return NULL
  staging: comedi: fix circular locking dependency in comedi_mmap()
  staging: r8723au: Add missing initialization of change_inx in sort algorithm
  Staging: unisys: use after free in list_for_each()
  staging: unisys: use after free in error messages
  staging: speakup: fix misuse of kstrtol() in handle_goto()
  staging: goldfish: Call free_irq in error path
  staging: delete rtl8187se wireless driver
  staging: rtl8723au: Fix buffer overflow in rtw_get_wfd_ie()
  staging: gs_fpgaboot: remove __TIMESTAMP__ macro
  staging: vme: fix memory leak in vme_user_probe()
  staging: fpgaboot: clean up Makefile
  staging/usbip: fix store_attach() sscanf return value check
  staging/usbip: userspace - fix usbipd SIGSEGV from refresh_exported_devices()
  staging: rtl8188eu: remove spaces, correct counts to unbreak P2P ioctls
  staging/rtl8821ae: Fix OOM handling in _rtl_init_deferred_work()

Pull tty/serial driver fixes from Greg KH:
 "Here are a number of small tty/serial driver fixes for 3.15-rc2.  Also
  in here are some Documentation file removals for drivers that we
  removed a long time ago, no need to keep it around any longer.

  All of these have been in linux-next for a bit"

* tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "serial: 8250, disable "too much work" messages"
  serial: amba-pl011: fix regression, causing an Oops on rmmod
  tty: Fix help text of SYNCLINK_CS
  tty: fix memleak in alloc_pid
  ttyprintk: Allow built as a module
  ttyprintk: Fix wrong tty_unregister_driver() call in the error path
  serial: 8250, disable "too much work" messages
  Documentation/serial: Delete obsolete driver documentation
  serial: omap: Fix missing pm_runtime_resume handling by simplifying code
  serial_core: Fix pm imbalance on unbind
  serial: pl011: change Rx burst size to half of trigger level
  serial: timberdale: Depend on X86_32
  serial: st-asc: Fix SysRq char handling
  Revert "serial: clps711x: Give a chance to perform useful tasks during wait loop"
  serial_core: Fix conditional start_tx on ring buffer not empty
  serial: efm32: use $vendor,$device scheme for compatible string
  serial: omap: free the wakeup settings in remove

Pull USB fixes from Greg KH:
 "Here are a number of tiny USB fixes and new device ids for 3.15-rc2.
  Nothing major, just issues some people have reported.

  All of these have been in linux-next"

* tag 'usb-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  uas: fix deadlocky memory allocations
  uas: fix error handling during scsi_scan()
  uas: fix GFP_NOIO under spinlock
  uwb: adds missing error handling
  USB: cdc-acm: Remove Motorola/Telit H24 serial interfaces from ACM driver
  USB: ohci-jz4740: FEAT_POWER is a port feature, not a hub feature
  USB: ohci-jz4740: Fix uninitialized variable warning
  USB: EHCI: tegra: set txfill_tuning
  usb: ehci-platform: Return immediately from suspend if ehci_suspend fails
  usb: ehci-exynos: Return immediately from suspend if ehci_suspend fails
  USB: fix crash during hotplug of PCI USB controller card
  USB: cdc-acm: fix double usb_autopm_put_interface() in acm_port_activate()
  usb: usb-common: fix typo for usb_state_string
  USB: usb_wwan: fix handling of missing bulk endpoints
  USB: pl2303: add ids for Hewlett-Packard HP POS pole displays
  USB: cp210x: Add 8281 (Nanotec Plug & Drive)
  usb: option driver, add support for Telit UE910v2
  Revert "USB: serial: add usbid for dell wwan card to sierra.c"
  USB: serial: ftdi_sio: add id for Brainboxes serial cards

Merge misc fixes from Andrew Morton:
 "13 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  thp: close race between split and zap huge pages
  mm: fix new kernel-doc warning in filemap.c
  mm: fix CONFIG_DEBUG_VM_RB description
  mm: use paravirt friendly ops for NUMA hinting ptes
  mips: export flush_icache_range
  mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
  wait: explain the shadowing and type inconsistencies
  Shiraz has moved
  Documentation/vm/numa_memory_policy.txt: fix wrong document in numa_memory_policy.txt
  powerpc/mm: fix ".__node_distance" undefined
  kernel/watchdog.c:touch_softlockup_watchdog(): use raw_cpu_write()
  init/Kconfig: move the trusted keyring config option to general setup
  vmscan: reclaim_clean_pages_from_list() must use mod_zone_page_state()

Sasha Levin has reported two THP BUGs[1][2].  I believe both of them
have the same root cause.  Let's look to them one by one.

The first bug[1] is "kernel BUG at mm/huge_memory.c:1829!".  It's
BUG_ON(mapcount != page_mapcount(page)) in __split_huge_page().  From my
testing I see that page_mapcount() is higher than mapcount here.

I think it happens due to race between zap_huge_pmd() and
page_check_address_pmd().  page_check_address_pmd() misses PMD which is
under zap:

	CPU0						CPU1
						zap_huge_pmd()
						  pmdp_get_and_clear()
__split_huge_page()
  anon_vma_interval_tree_foreach()
    __split_huge_page_splitting()
      page_check_address_pmd()
        mm_find_pmd()
	  /*
	   * We check if PMD present without taking ptl: no
	   * serialization against zap_huge_pmd(). We miss this PMD,
	   * it's not accounted to 'mapcount' in __split_huge_page().
	   */
	  pmd_present(pmd) == 0

  BUG_ON(mapcount != page_mapcount(page)) // CRASH!!!

						  page_remove_rmap(page)
						    atomic_add_negative(-1, &page->_mapcount)

The second bug[2] is "kernel BUG at mm/huge_memory.c:1371!".
It's VM_BUG_ON_PAGE(!PageHead(page), page) in zap_huge_pmd().

This happens in similar way:

	CPU0						CPU1
						zap_huge_pmd()
						  pmdp_get_and_clear()
						  page_remove_rmap(page)
						    atomic_add_negative(-1, &page->_mapcount)
__split_huge_page()
  anon_vma_interval_tree_foreach()
    __split_huge_page_splitting()
      page_check_address_pmd()
        mm_find_pmd()
	  pmd_present(pmd) == 0	/* The same comment as above */
  /*
   * No crash this time since we already decremented page->_mapcount in
   * zap_huge_pmd().
   */
  BUG_ON(mapcount != page_mapcount(page))

  /*
   * We split the compound page here into small pages without
   * serialization against zap_huge_pmd()
   */
  __split_huge_page_refcount()
						VM_BUG_ON_PAGE(!PageHead(page), page); // CRASH!!!

So my understanding the problem is pmd_present() check in mm_find_pmd()
without taking page table lock.

The bug was introduced by me commit with commit 117b0791. Sorry for
that. :(

Let's open code mm_find_pmd() in page_check_address_pmd() and do the
check under page table lock.

Note that __page_check_address() does the same for PTE entires
if sync != 0.

I've stress tested split and zap code paths for 36+ hours by now and
don't see crashes with the patch applied. Before it took <20 min to
trigger the first bug and few hours for second one (if we ignore
first).

[1] https://lkml.kernel.org/g/<53440991.9090001@oracle.com>
[2] https://lkml.kernel.org/g/<5310C56C.60709@oracle.com>
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: NSasha Levin <sasha.levin@oracle.com>
Tested-by: NSasha Levin <sasha.levin@oracle.com>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michel Lespinasse <walken@google.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>	[3.13+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix new kernel-doc warning in mm/filemap.c:

  Warning(mm/filemap.c:2600): Excess function parameter 'ppos' description in '__generic_file_aio_write'
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This appears to be a copy/paste error.  Update the description to
reflect extra rbtree debug and checks for the config option instead of
duplicating CONFIG_DEBUG_VM.
Signed-off-by: NDavidlohr Bueso <davidlohr@hp.com>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>