Avoid secure transactions while probing the CCI PMU. The
existing code makes use of the Peripheral ID2 (PID2) register
to determine the revision of the CCI400, which requires a
secure transaction. This puts a limitation on the usage of the
driver on systems running non-secure Linux(e.g, ARM64).

Updated the device-tree binding for cci pmu node to add the explicit
revision number for the compatible field.

The supported strings are :
	arm,cci-400-pmu,r0
	arm,cci-400-pmu,r1
	arm,cci-400-pmu - DEPRECATED. See NOTE below

NOTE: If the revision is not mentioned, we need to probe the cci revision,
which could be fatal on a platform running non-secure. We need a reliable way
to know if we can poke the CCI registers at runtime on ARM32. We depend on
'mcpm_is_available()' when it is available. mcpm_is_available() returns true
only when there is a registered driver for mcpm. Otherwise, we assume that we
don't have secure access, and skips probing the revision number(ARM64 case).

The MCPM should figure out if it is safe to access the CCI. Unfortunately
there isn't a reliable way to indicate the same via dtb. This patch doesn't
address/change the current situation. It only deals with the CCI-PMU, leaving
the assumptions about the secure access as it has been, prior to this patch.

Cc: devicetree@vger.kernel.org
Cc: Punit Agrawal <punit.agrawal@arm.com>
Tested-by: NSudeep Holla <sudeep.holla@arm.com>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NSuzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Under arm64, we will calibrate the delay loop statically using a known
timer frequency, so delete read_current_timer(), or it will cause
compiling issue with allmodconfig.

The related error:
  ERROR: "read_current_timer" [lib/rbtree_test.ko] undefined!
  ERROR: "read_current_timer" [lib/interval_tree_test.ko] undefined!
  ERROR: "read_current_timer" [fs/ext4/ext4.ko] undefined!
  ERROR: "read_current_timer" [crypto/tcrypt.ko] undefined!
Signed-off-by: NChen Gang <gang.chen@asianux.com>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch adds support for the ARM generic timers with A64 instructions
for accessing the timer registers. It uses the physical counter as the
clock source and the virtual counter as sched_clock.

The timer frequency can be specified via DT or read from the CNTFRQ_EL0
register. The physical counter is also accessible from user space
allowing fast gettimeofday() implementation.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The virtual memory layout is described in
Documentation/arm64/memory.txt. This patch adds the MMU definitions for
the 4KB and 64KB translation table configurations. The SECTION_SIZE is
2MB with 4KB page and 512MB with 64KB page configuration.

PHYS_OFFSET is calculated at run-time and stored in a variable (no
run-time code patching at this stage).

On the current implementation, both user and kernel address spaces are
512G (39-bit) each with a maximum of 256G for the RAM linear mapping.
Linux uses 3 levels of translation tables with the 4K page configuration
and 2 levels with the 64K configuration. Extending the memory space
beyond 39-bit with the 4K pages or 42-bit with 64K pages requires an
additional level of translation tables.

The SPARSEMEM configuration is global to all AArch64 platforms and
allows for 1GB sections with SPARSEMEM_VMEMMAP enabled by default.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The patch adds the kernel booting and the initial setup code.
Documentation/arm64/booting.txt describes the booting protocol on the
AArch64 Linux kernel. This is subject to change following the work on
boot standardisation, ACPI.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Add support for the Infineon TLE62x0 series of low-side driver chips, such
as the TLE6220 or TLE6230.  These can be viewed as output GPIOs specialized
for power switching applications.  The driver provides a userspace
interface to those GPIOs, and to the switch status they provide.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Patch from Sascha Hauer

This patch adds the base support for Hilscher's netX network
processors.
Signed-off-by: NRobert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from SAN People

Following changes were made to clock.c:

1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.

Otherwise it's the same as the previous patch.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rationalise hardware.h include.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!