Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 20 12月, 2013 3 次提交
  3. 18 12月, 2013 5 次提交
  5. 14 12月, 2013 9 次提交
  7. 07 12月, 2013 2 次提交
  9. 29 11月, 2013 1 次提交
  11. 16 11月, 2013 1 次提交
  13. 15 11月, 2013 1 次提交
  15. 14 11月, 2013 1 次提交
  17. 08 11月, 2013 1 次提交
  19. 20 10月, 2013 3 次提交
  21. 18 10月, 2013 1 次提交
  23. 04 10月, 2013 1 次提交
    • N
      bonding: modify the old and add new xmit hash policies · 32819dc1
      由 Nikolay Aleksandrov 提交于 
      This patch adds two new hash policy modes which use skb_flow_dissect:
3 - Encapsulated layer 2+3
4 - Encapsulated layer 3+4
There should be a good improvement for tunnel users in those modes.
It also changes the old hash functions to:
hash ^= (__force u32)flow.dst ^ (__force u32)flow.src;
hash ^= (hash >> 16);
hash ^= (hash >> 8);

Where hash will be initialized either to L2 hash, that is
SRCMAC[5] XOR DSTMAC[5], or to flow->ports which should be extracted
from the upper layer. Flow's dst and src are also extracted based on the
xmit policy either directly from the buffer or by using skb_flow_dissect,
but in both cases if the protocol is IPv6 then dst and src are obtained by
ipv6_addr_hash() on the real addresses. In case of a non-dissectable
packet, the algorithms fall back to L2 hashing.
The bond_set_mode_ops() function is now obsolete and thus deleted
because it was used only to set the proper hash policy. Also we trim a
pointer from struct bonding because we no longer need to keep the hash
function, now there's only a single hash function - bond_xmit_hash that
works based on bond->params.xmit_policy.

The hash function and skb_flow_dissect were suggested by Eric Dumazet.
The layer names were suggested by Andy Gospodarek, because I suck at
semantics.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Acked-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      32819dc1
  25. 27 9月, 2013 5 次提交
    • T
      sysfs: make attr namespace interface less convoluted · 58292cbe
      由 Tejun Heo 提交于 
      sysfs ns (namespace) implementation became more convoluted than
necessary while trying to hide ns information from visible interface.
The relatively recent attr ns support is a good example.

* attr ns tag is determined by sysfs_ops->namespace() callback while
  dir tag is determined by kobj_type->namespace().  The placement is
  arbitrary.

* Instead of performing operations with explicit ns tag, the namespace
  callback is routed through sysfs_attr_ns(), sysfs_ops->namespace(),
  class_attr_namespace(), class_attr->namespace().  It's not simpler
  in any sense.  The only thing this convolution does is traversing
  the whole stack backwards.

The namespace callbacks are unncessary because the operations involved
are inherently synchronous.  The information can be provided in in
straight-forward top-down direction and reversing that direction is
unnecessary and against basic design principles.

This backward interface is unnecessarily convoluted and hinders
properly separating out sysfs from driver model / kobject for proper
layering.  This patch updates attr ns support such that

* sysfs_ops->namespace() and class_attr->namespace() are dropped.

* sysfs_{create|remove}_file_ns(), which take explicit @ns param, are
  added and sysfs_{create|remove}_file() are now simple wrappers
  around the ns aware functions.

* ns handling is dropped from sysfs_chmod_file().  Nobody uses it at
  this point.  sysfs_chmod_file_ns() can be added later if necessary.

* Explicit @ns is propagated through class_{create|remove}_file_ns()
  and netdev_class_{create|remove}_file_ns().

* driver/net/bonding which is currently the only user of attr
  namespace is updated to use netdev_class_{create|remove}_file_ns()
  with @bh->net as the ns tag instead of using the namespace callback.

This patch should be an equivalent conversion without any functional
difference.  It makes the code easier to follow, reduces lines of code
a bit and helps proper separation and layering.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      58292cbe
    • V
      net: create sysfs symlinks for neighbour devices · 5831d66e
      由 Veaceslav Falico 提交于 
      Also, remove the same functionality from bonding - it will be already done
for any device that links to its lower/upper neighbour.

The links will be created for dev's kobject, and will look like
lower_eth0 for lower device eth0 and upper_bridge0 for upper device
bridge0.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5831d66e
    • V
      net: expose the master link to sysfs, and remove it from bond · 842d67a7
      由 Veaceslav Falico 提交于 
      Currently, we can have only one master upper neighbour, so it would be
useful to create a symlink to it in the sysfs device directory, the way
that bonding now does it, for every device. Lower devices from
bridge/team/etc will automagically get it, so we could rely on it.

Also, remove the same functionality from bonding.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      842d67a7
    • V
      bonding: add bond_has_slaves() and use it · 0965a1f3
      由 Veaceslav Falico 提交于 
      Currently we verify if we have slaves by checking if bond->slave_list is
empty. Create a define bond_has_slaves() and use it, a bit more readable
and easier to change in the future.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0965a1f3
    • V
      bonding: make bond_for_each_slave() use lower neighbour's private · 9caff1e7
      由 Veaceslav Falico 提交于 
      It needs a list_head *iter, so add it wherever needed. Use both non-rcu and
rcu variants.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9caff1e7
  27. 16 9月, 2013 1 次提交
  29. 12 9月, 2013 2 次提交
  31. 04 9月, 2013 1 次提交
  33. 02 8月, 2013 2 次提交
    • N
      bonding: initial RCU conversion · 278b2083
      由 nikolay@redhat.com 提交于 
      This patch does the initial bonding conversion to RCU. After it the
following modes are protected by RCU alone: roundrobin, active-backup,
broadcast and xor. Modes ALB/TLB and 3ad still acquire bond->lock for
reading, and will be dealt with later. curr_active_slave needs to be
dereferenced via rcu in the converted modes because the only thing
protecting the slave after this patch is rcu_read_lock, so we need the
proper barrier for weakly ordered archs and to make sure we don't have
stale pointer. It's not tagged with __rcu yet because there's still work
to be done to remove the curr_slave_lock, so sparse will complain when
rcu_assign_pointer and rcu_dereference are used, but the alternative to use
rcu_dereference_protected would've created much bigger code churn which is
more difficult to test and review. That will be converted in time.

1. Active-backup mode
 1.1 Perf recording while doing iperf -P 4
  - old bonding: iperf spent 0.55% in bonding, system spent 0.29% CPU
                 in bonding
  - new bonding: iperf spent 0.29% in bonding, system spent 0.15% CPU
                 in bonding
 1.2. Bandwidth measurements
  - old bonding: 16.1 gbps consistently
  - new bonding: 17.5 gbps consistently

2. Round-robin mode
 2.1 Perf recording while doing iperf -P 4
  - old bonding: iperf spent 0.51% in bonding, system spent 0.24% CPU
                 in bonding
  - new bonding: iperf spent 0.16% in bonding, system spent 0.11% CPU
                 in bonding
 2.2 Bandwidth measurements
  - old bonding: 8 gbps (variable due to packet reorderings)
  - new bonding: 10 gbps (variable due to packet reorderings)

Of course the latency has improved in all converted modes, and moreover
while
doing enslave/release (since it doesn't affect tx anymore).

Also I've stress tested all modes doing enslave/release in a loop while
transmitting traffic.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      278b2083
    • N
      bonding: convert to list API and replace bond's custom list · dec1e90e
      由 nikolay@redhat.com 提交于 
      This patch aims to remove struct bonding's first_slave and struct
slave's next and prev pointers, and replace them with the standard Linux
list API. The old macros are converted to list API as well and some new
primitives are available now. The checks if there're slaves that used
slave_cnt have been replaced by the list_empty macro.
Also a few small style fixes, changing longest -> shortest line in local
variable declarations, leaving an empty line before return and removing
unnecessary brackets.
This is the first step to gradual RCU conversion.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      dec1e90e