No semantic changes.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

It only needs the iommu_table address.  It also makes use of the node
name to print error messages.  So just pass it the things it needs.
This reduces the places that know about the pci_dn by one.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The 'data' member of proc_ppc64_lparcfg is unused, but the lparcfg
module's init routine allocates 4K for it.

Remove the code which allocates and frees this buffer.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NKou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds support for native CBE on Celleb, that is, without the BEAT
hypervisor.  Many codes in platforms/cell/ are used in native CBE
environment.
Signed-off-by: NKou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes the following link error with CONFIG_PPC_CELL_NATIVE=y and
CONFIG_PPC_CELL_BLADE=n:

arch/powerpc/platforms/built-in.o: In function `.cell_setup_arch':
setup.c:(.init.text+0xe80): undefined reference to `.mmio_nvram_init'
Signed-off-by: NKou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

so consolidate it into misc.S.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add for_each_child_of_node() to encapsulate the common idiom of
iterating over the children of a device_node.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Also use of_unregister_driver to implement of_unregister_platform_driver.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: kill spurious NCQ completion detection
  ahci: don't attach if ICH6 is in combined mode
  ata_piix: add Toshiba Tecra M4 to broken suspend list
  ahci: fix engine reset failed message

Spurious NCQ completion detection implemented in ahci was incorrect.
On AHCI receving and processing FISes and raising interrupts are not
interlocked and spurious interrupts are expected.

For example, if an interrupt occurs while interrupt handler is running
and the running interrupt handler handles the event the new IRQ
indicated, after IRQ handler finishes, it will be executed again
because IRQ pending bit is set by the new interrupt but there won't be
anything to process.

Please read the following message for more information.

  http://article.gmane.org/gmane.linux.ide/26012

This patch...

* Removes all spurious IRQ whining from ahci.  Spurious NCQ completion
  detection was completely wrong.  Spurious D2H Register FIS taught us
  that some early drives send spurious D2H Register FIS with I bit set
  while NCQ commands are in progress but none of recent drives does
  that and even the ones which show such behavior can do NCQ fine.

* Kills all NCQ blacklist entries which were added because of spurious
  NCQ completions.  I tracked down each commit and verified all
  removed ones are actually added because of spurious completions.

  WD740ADFD-00NLR1 wasn't deleted but moved upward because the drive
  not only had spurious NCQ completions but also is slow on sequential
  data transfers if NCQ is enabled.

  Maxtor 7V300F0 was added by 0e3dbc01
  from Alan Cox.  I can only find evidences that the drive only had
  troubles with spuruious completions by searching the mailing list.
  This entry needs to be verified and removed if it doesn't have other
  NCQ related problems.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ICH6 R/Ms share PCI ID between piix and ahci modes and we've been
allowing ahci to attach regardless of how BIOS configured it.
However, enabling AHCI mode when the controller is in combined mode
can result in unexpected behavior.  Don't attach if the controller is
in combined mode.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Bill Nottingham <notting@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add Toshiba Tecra M4 to broken suspend list.  This is from OSDL
bugzilla bug 7780.
Signed-off-by: NPeter Schwenke <peter@bluetoad.com.au>
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There isn't much point in reporting -EOPNOTSUPP as failure.  Also the
message was missing newline.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Making sure register initialisation is complete before proceeding further.
  The driver must wait until initialization is complete before attempting to
  access any other device registers.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This updates the copyright notices of the new EMAC driver to
avoid confusion as who is to be blamed for new bugs.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The patch moves dev_set_drvdata(&ofdev->dev, dev) up before tah_reset(ofdev)
is called to avoid a NULL pointer dereference, since tah_reset uses drvdata.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes a typo in ibm_newemac/core.c
(tah_port should be used instead of tah_ph)
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The EMAC4_MR1_OBCI(freq) macro expects freg in MHz,
while opb_bus_freq is kept in Hz. Correct this.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Depending on how the 44x processors are wired, some EMAC cells
might not be useable (and not connected to a PHY). However, some
device-trees may choose to still expose them (since their registers
are present in the MMIO space) but with an "unused" property in them.
Signed-off-by: NHugh Blemings <hugh@blemings.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There are a few variants of the STACR register that affect more than
just the "AXON" version of EMAC. Replace the current test of various
chip models with tests for generic properties in the device-tree.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

More than just "AXON" version of EMAC RGMII supports MDIO, so replace
the current test with a generic property in the device-tree that
indicates such support.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

With some PHYs, when the link goes away, the EMAC reset fails due
to the loss of the RX clock I believe.

The old EMAC driver worked around that using some internal chip-specific
clock force bits that are different on various 44x implementations.

This is an attempt at doing it differently, by avoiding the reset when
there is no link, but forcing loopback mode instead. It seems to work
on my Taishan 440GX based board so far.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When using ZMII for MDIO only (such as 440GX with RGMII for data and ZMII for
MDIO), the ZMII code would fail to properly refcount, thus triggering a
BUG_ON().
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This adds support for the Agere ET1011c PHY as found on the AMCC Taishan
board.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds BCM5248 and Marvell 88E1111 PHY support to NEW EMAC driver.
These PHY chips are used on PowerPC 440EPx boards.
The PHY code is based on the previous work by Stefan Roese <sr@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

No need to convert to bytes and back - cleanup unneeded code.

Adapted from fix from 'Roel Kluin <12o3l@tiscali.nl>'
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

drivers/net/e1000/e1000_ethtool.c:113:
#define E1000_TEST_LEN sizeof(e1000_gstrings_test) / ETH_GSTRING_LEN

drivers/net/e1000e/ethtool.c:106:
#define E1000_TEST_LEN sizeof(e1000_gstrings_test) / ETH_GSTRING_LEN

E1000_TEST_LEN*ETH_GSTRING_LEN will expand to
sizeof(e1000_gstrings_test) / (ETH_GSTRING_LEN * ETH_GSTRING_LEN)

A lack of parentheses around defines causes unexpected results due to
operator precedences.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The bnx2x module depends on the zlib_inflate functions.  The
build will fail if ZLIB_INFLATE has not been selected manually
or by building another module that automatically selects it.

Modify BNX2X config option to 'select ZLIB_INFLATE' like BNX2
and others.  This seems to fix it.
Signed-off-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update GPIO mapping for T3C.
Update xgmac for T3C support.
Fix typo in mtu table.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Fixes a race condition in module unload.  Without this change,
workqueue events may fire while bonding data structures are partially
freed but before bond_close() is invoked by unregister_netdevice().

	Update version to 3.2.3.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

 	Add new hash for balance-xor and 802.3ad modes.  Originally
 submitted by "Glenn Griffin" <ggriffin.kernel@gmail.com>; modified by
 Jay Vosburgh to move setting of hash policy out of line, tweak the
 documentation update and add version update to 3.2.2.

	Glenn's original comment follows:

Included is a patch for a new xmit_hash_policy for the bonding driver
that selects slaves based on MAC and IP information.  This is a middle
ground between what currently exists in the layer2 only policy and the
layer3+4 policy.  This policy strives to be fully 802.3ad compliant by
transmitting every packet of any particular flow over the same link.
As documented the layer3+4 policy is not fully compliant for extreme
cases such as ip fragmentation, so this policy is a nice compromise
for environments that require full compliance but desire more than the
layer2 only policy.
Signed-off-by: N"Glenn Griffin" <ggriffin.kernel@gmail.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: David Sterba <dsterba@suse.cz>

Use macros for comparing jiffies. Jiffies' wrap caused missed events and hangs.
Module reinsert was needed to make bonding work again.
Signed-off-by: NDavid Sterba <dsterba@suse.cz>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Wagner Ferenc <wferi@niif.hu>

For consistency with the behaviour of the arp_ip_target option,
let /sys/class/net/bond0/bonding/xmit_hash_policy accept and report
current policy even if the bonding mode in effect does not use it.
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Wagner Ferenc <wferi@niif.hu>

Adhere to coding style: break line after the if condition
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Wagner Ferenc <wferi@niif.hu>

Code for rendering multivalue sysfs files occurs three times
in this module.  Rename 'buffer' to 'buf' in the first, for
the sake of consistency.
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Wagner Ferenc <wferi@niif.hu>

The previous code returned '\n' (that is, a single empty line)
from most files, with one exception (xmit_hash_policy), where
it returned 'NA\n'.  This patch consolidates each file to return
nothing at all if not applicable, not even a '\n'.

I find this behaviour more usual, more useful, more efficient
and shorter to code from both sides.
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Wagner Ferenc <wferi@niif.hu>

Also remove trailing spaces from multivalued files.

This fixes output like for example:

$ od -c /sys/class/net/bond0/bonding/slaves
0000000   e   t   h   -   l   e   f   t       e   t   h   -   r   i   g
0000020   h   t      \n  \0
0000025

It mostly entails deleting '+1'-s after sprintf() calls: the return value
of sprintf is the number of characters printed, without the closing NUL,
ie. exactly what the sysfs interface requires.  The three multivalue
cases are different, because they also have to swallow back a trailing
space.
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>