Get rid of the use of local IO access macros and switch to using the standard
read*/write* family of access functions for the ColdFire m532x setup code.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The ColdFire 532x CPU register definitions for the multi-function setup
pins are inconsistently defined compared with other ColdFire parts. Modify
the register defintions to be just the addresses, not pointers. This also
fixes the erroneous use in one case of using these values in the UART setup
code for the 532x.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

There are a lot of unused and uneccessary definitions in the header to
support the ColdFire 532x CPU family. Remove the junk.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The 532x has individually controllable clocks for it peripherals.  Add clk
definitions for these and add default initialization of either enabled or
disabled.
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

m68knommu: add definitions for the third interrupt controller on devices that don't have a third interrupt controller.

Extending the interrupt controller code in  intc-simr.c to support the third
interrupt controller on the m5441x means we need to add defines (as 0) for the
third interrupt controller on devices that don't have a third interrupt
controller.
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

If we make all QSPI (SPI protocol) addressing consistent across all ColdFire
family members then we will be able to remove the duplicated plaform data
and code and use a single setup for all.

So modify the ColdFire 532x QSPI addressing so that:

. base addresses are absolute (not relative to MBAR peripheral register)
. use a common name for IRQs used
. move chip select definitions (CS) to appropriate header
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

If we make all FEC (ethernet) addressing consistent across all ColdFire
family members then we will be able to remove the duplicated plaform data
and use a single setup for all.

So modify the ColdFire 532x FEC addressing so that:

. FECs are numbered from 0 up
. base addresses are absolute (not relative to MBAR peripheral register)
. use a common name for IRQs used
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

If we make all UART addressing consistent across all ColdFire family members
then we will be able to remove the duplicated plaform data and use a single
setup for all.

So modify the ColdFire 532x UART addressing so that:

. UARTs are numbered from 0 up
. use a common name for IRQs used
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The reality is that you do not need the abiltity to configure the
clock divider for ColdFire CPUs. It is a fixed ratio on any given
ColdFire family member. It is not the same for all ColdFire parts,
but it is always the same in a model range. So hard define the divider
for each supported ColdFire CPU type and remove the Kconfig option.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Not all ColdFire CPUs that use the old style timer hardware module use
an MBAR set peripheral region. Move the TIMER base address defines to the
per-CPU header files where we can set it correctly based on how the
peripherals are mapped - instead of using a fake MBAR for some platforms.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

All version 3 based ColdFire CPU cores have a similar cache controller.
Merge all the exitsing definitions into a single file, and make them
similar in style and naming to the existing version 2 and version 4
cache controller definitions.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The ColdFire UART base addresses varies between the different ColdFire
family members. Instead of keeping the base addresses with the UART
definitions keep them with the other addresses definitions for each
ColdFire part.

The motivation for this move is so that when we add new ColdFire
part definitions, they are all in a single file (and we shouldn't
normally need to modify the UART definitions in mcfuart.h at all).
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The instruction timings of the ColdFire 54xx family parts are
different to other version 4 parts (or version 2 or 3 parts for
that matter too).

Move the instruction timing setting into the ColdFire part
specific headers, and set the 54xx value appropriately.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Move the ColdFire CPU names out of setup.c and into their repsective
headers. That way when we add new ones we won't need to modify
setup.c any more.

Add the missing 548x CPU name.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Since Grant has added the coldfire-qspi driver to next-spi, here is the
platform support for the parts that have qspi hardware.  This sets up
gpio to do the spi chip select using the default chip select pins; it should
be trivial for boards that require different or additional spi chip selects to
use other gpios as needed.
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The newer ColdFire 532x family of CPU's uses the old timer, but has a
newer interrupt controller. It doesn't need the special timer setup
that was required when using the older interrupt controller. Remove the
dead timer irq and level setting code, and define the hard coded vector.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The ColdFire intc-simr interrupt controller should mask off all
interrupt sources at init time. Doing it here instead of separately
in each platform setup.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The ColdFire 532x family of parts uses 2 of the same INTC interrupt
controlers used in the ColdFire 520x family. So modify the code to
support both parts. The extra code for the second INTC controler in
the case of the 520x is easily optimized away to nothing.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Add support for the 532x.
Signed-off-by: NSteven King <sfking@fdwdc.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Signed-off-by: NDavid Wu <david.wu@arcturusnetworks.com>
Acked-by: NMichael Durrant <mdurrant@arcturusnetworks.com>
Acked-by: NOleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Merge header files for m68k and m68knommu to the single location:

    arch/m68k/include/asm

The majority of this patch was the result of the
script that is included in the changelog below.

The script was originally written by Arnd Bergman and
exten by me to cover a few more files.

When the header files differed the script uses the following:

The original m68k file is named <file>_mm.h  [mm for memory manager]
The m68knommu file is named <file>_no.h [no for no memory manager]

The files uses the following include guard:

This include gaurd works as the m68knommu toolchain set
the __uClinux__ symbol - so this should work in userspace too.

Merging the header files for m68k and m68knommu exposes the
(unexpected?) ABI differences thus it is easier to actually
identify these and thus to fix them.

The commit has been build tested with both a m68k and
a m68knommu toolchain - with success.

The commit has also been tested with "make headers_check"
and this patch fixes make headers_check for m68knommu.

The script used:
TARGET=arch/m68k/include/asm
SOURCE=arch/m68knommu/include/asm

INCLUDE="cachectl.h errno.h fcntl.h hwtest.h ioctls.h ipcbuf.h \
linkage.h math-emu.h md.h mman.h movs.h msgbuf.h openprom.h \
oplib.h poll.h posix_types.h resource.h rtc.h sembuf.h shmbuf.h \
shm.h shmparam.h socket.h sockios.h spinlock.h statfs.h stat.h \
termbits.h termios.h tlb.h types.h user.h"

EQUAL="auxvec.h cputime.h device.h emergency-restart.h futex.h \
ioctl.h irq_regs.h kdebug.h local.h mutex.h percpu.h \
sections.h topology.h"

NOMUUFILES="anchor.h bootstd.h coldfire.h commproc.h dbg.h \
elia.h flat.h m5206sim.h m520xsim.h m523xsim.h m5249sim.h \
m5272sim.h m527xsim.h m528xsim.h m5307sim.h m532xsim.h \
m5407sim.h m68360_enet.h m68360.h m68360_pram.h m68360_quicc.h \
m68360_regs.h MC68328.h MC68332.h MC68EZ328.h MC68VZ328.h \
mcfcache.h mcfdma.h mcfmbus.h mcfne.h mcfpci.h mcfpit.h \
mcfsim.h mcfsmc.h mcftimer.h mcfuart.h mcfwdebug.h \
nettel.h quicc_simple.h smp.h"

FILES="atomic.h bitops.h bootinfo.h bug.h bugs.h byteorder.h cache.h \
cacheflush.h checksum.h current.h delay.h div64.h \
dma-mapping.h dma.h elf.h entry.h fb.h fpu.h hardirq.h hw_irq.h io.h \
irq.h kmap_types.h machdep.h mc146818rtc.h mmu.h mmu_context.h \
module.h page.h page_offset.h param.h pci.h pgalloc.h \
pgtable.h processor.h ptrace.h scatterlist.h segment.h \
setup.h sigcontext.h siginfo.h signal.h string.h system.h swab.h \
thread_info.h timex.h tlbflush.h traps.h uaccess.h ucontext.h \
unaligned.h unistd.h"

mergefile() {
	BASE=${1%.h}
	git mv ${SOURCE}/$1 ${TARGET}/${BASE}_no.h
	git mv ${TARGET}/$1 ${TARGET}/${BASE}_mm.h

cat << EOF > ${TARGET}/$1
EOF

	git add ${TARGET}/$1
}

set -e

mkdir -p ${TARGET}

git mv include/asm-m68k/* ${TARGET}
rmdir include/asm-m68k

git rm ${SOURCE}/Kbuild
for F in $INCLUDE $EQUAL; do
	git rm ${SOURCE}/$F
done

for F in $NOMUUFILES; do
	git mv ${SOURCE}/$F ${TARGET}/$F
done

for F in $FILES ; do
	mergefile $F
done

rmdir arch/m68knommu/include/asm
rmdir arch/m68knommu/include

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

With the current kbuild infrastructure in place no other changes
are required for this to work.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Register definitions for the new Freescale 532x Coldfire CPU family.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>