SBC-iMX7 is a single board computer designed for industrial
and embedded applications. It is based on the Freescale i.MX7
system-on-chip. SBC-iMX7 is implemented with the CL-SOM-iMX7
System-on-Module providing most of the functions, and SB-SOM-iMX7
carrier board providing additional peripheral functions and
connectors.

http://www.compulab.co.il/products/sbcs/sbc-imx7-freescale-i-mx-7-single-board-computer/

http://www.compulab.co.il/products/computer-on-modules/cl-som-imx7-freescale-i-mx-7-system-on-module/

Add basic board support, including SD card as a secondary boot and storage device
Signed-off-by: NIlya Ledvich <ilya@compulab.co.il>
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>

CL-SOM-iMX7 is a miniature System-on-Module (SoM) based on
Freescale i.MX7 System-on-Chip family.

http://www.compulab.co.il/products/computer-on-modules/cl-som-imx7-freescale-i-mx-7-system-on-module/

Add basic DT support for standalone module (without a carrier board):

* Memory configuration
* eMMC
* 2x Gigabit Ethernet ports (FEC1 and FEC2)
* I2C2 bus
  * EEPROM
  * PCA9555 GPIO extender
  * PMIC
* UART1
* USB OTG port
Signed-off-by: NIlya Ledvich <ilya@compulab.co.il>
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>

This commit enables the touchscreen on TS-4800, using the ts4800-ts
driver.
Signed-off-by: NDamien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This commit adds LCD support for the TS-4800. The panel is an Okaya
RS800480T-7X0WQ and the timings have been extracted from Technologic
Systems' tree.
Signed-off-by: NDamien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Novena is an open-hardware laptop/desktop/bare board.

See http://www.kosagi.com/w/index.php?title=Novena_Main_PageSigned-off-by: NSean Cross <xobs@kosagi.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Previously, the device tree mapped the FPGA like any other IPs inside
the SoC, but it is actually mapped through the WEIM (Wireless External
Interface Module). This patch updates the device tree to make use of it.

About the timings: in the image provided by the manufacturer, only
CS0GCR1 is changed. The other values are the default ones, but the WEIM
bindings expect them to be all explicitly set in the device tree, so I
just put the default values in the dt.
Signed-off-by: NDamien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

These pins are actually not routed for UARTs, they should not be
reserved.
Signed-off-by: NDamien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This adds the device nodes for 2D, 3D and VG GPU cores.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add auart4 2-pin configuration on auart0 rts/cts pads.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Added sata node to ls1021aqds and ls1021atwr board to support
sata function.
Signed-off-by: NTang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This device tree adds support for TS-4800 by Technologic Systems. This
board is based on MX51-babbage, but there are some subtle differences in
the pins used, and there is an additional FPGA that is memory-mapped.

More details here:
  http://wiki.embeddedarm.com/wiki/TS-4800Signed-off-by: NDamien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add ADC support for imx7d-sdb board.
Signed-off-by: NHaibo Chen <haibo.chen@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add imx7d ADC support.
Signed-off-by: NHaibo Chen <haibo.chen@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add Colibri standard pinmux for FlexCAN controller instances. CAN
is not a standard Colibri feature, but the datasheet predefines
pins which provide CAN (compatible across some modules). Hence,
add the pinmux on module level.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The backlight PWM is actually pwm4.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

No functional change, just moving the node to the place where it
belongs according to its unit address.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This allows for consistent numbering of the IPU output and
input ports.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This has been moved to the reg property where it belongs for quite some
time. The range has been unused by the kernel since then and with kernel
4.4 it's flagged as an unparsable range, as it does not comply to the
PCI ranges DT binding. Fix this by removing the superfluous range.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Audio IP need the spba clock, but original clock name "dma" is not
accurate, so change it to name "spba". The audio driver has been
using the new name "spba", the binding document has been updated.
Signed-off-by: NShengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NAlison Wang <b18965@freescale.com>
Signed-off-by: NXiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: NJianwei Wang <jianwei.wang.chn@gmail.com>
Signed-off-by: NMeng Yi <b56799@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NAlison Wang <b18965@freescale.com>
Signed-off-by: NXiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: NJianwei Wang <jianwei.wang.chn@gmail.com>
Signed-off-by: NMeng Yi <b56799@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

As on i.MX7D, we using a virtual arm clk for CPU frequency
scaling, so correct the clocks info used by the cpufreq driver.
Signed-off-by: NBai Ping <b51503@freescale.com>
Acked-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This addes support for SPI available on an off-board connector available on
some models of the GW52xx.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Ventana boards have an off-board connector with signals that can be pinmuxed
as either GPIO or PWM. This patch adds pwm device-tree nodes in the disabled
state which the bootloader can decide to enable based on bootloader config.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Minimal Cortex-M4 device tree to boot Linux to shell. M4 is booted via
Cortex-A5 running Linux using Stefan Agner's <stefan@agner.ch> "m4boot"
utility.
Signed-off-by: NAfzal Mohammed <afzal.mohd.ma@gmail.com>
Acked-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Extend the existing Vybrid DSPI devicetree implementation to also
describe the dspi2 and dspi3 functional blocks.
Signed-off-by: NCory Tusar <cory.tusar@pid1solutions.com>
Acked-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This, together with the corresponding patch to pwm-imx.c,  allows to order the
pwm devices correctly.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

imx6qdl.dtsi uses compatibles "fsl,imx6q-gpt", "fsl,imx31-gpt".
imx6dl.dtsi uses compatibles "fsl,imx6dl-gpt", "fsl,imx6q-gpt" since
commit

	4e415ed8 (ARM: dts: imx6dl: add imx6dl gpt specific compatible string)

If imx6dl would be compatible with imx6q-gpt it would also have to be
compatible with imx31-gpt which is currently missing.

Based on the above mentioned patch I assume imx6q-gpt and imx6dl-gpt are
not compatible. So imx6q-gpt should be removed as compatible.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Currently it is not possible to have HDMI and LVDS working simultaneously,
because both ports try to use PLL5.

Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
driven from independent sources.

With this change the LDB pixel clock goes to 68.57 MHz, which is still
within the valid range for the displays supported by the Ventana boards.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The GW54xx PMIC swbst regulator is used for LVDS power, CANbus xceiver
and HDMI DDC and is enabled by the bootloader. Set the regulator to
always-on so that Linux doesn't turn it off thinking its not needed.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This patch adds some values that are needed for an out-of-tree device
tree I'm currently working with.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for ADC1.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Specify the 'adck-max-frequency' property in the adc nodes.

According to Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
this is a recommended property.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

It can improve the USB performance when choosing larger
burst size at some systems (bus size is larger), there is
no side effect if this burst size is larger than bus size.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

After setting ahb burst configuration as 0, we can increase tx/rx
burst size, it will improve the USB performance
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add pdmic node on sama5d2-xplained board.The pdmic
pins conflict with ISC_D0 & ISC_D1 data pins.
Signed-off-by: NSongjun Wu <songjun.wu@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add pdmic node.
Signed-off-by: NSongjun Wu <songjun.wu@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The development kit uses a TSC2004 chip attached to I2C3.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet,
featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack.

Empire Electronix is written on the back of the tablet, the D709 model
info can be found in the about tablet menu in android.

The PCB has no markings to speak of.

This dts file does not add support for the ft5x touchscreen found at
i2c bus 1, addr 0x38, irq PG11, because it does not work out of the box.
It seems it has been flashed with the wrong firmware and needs to have
alternative firmware uploaded at boot to make the touchscreen work
properly, when hot-booting from android into an upstream kernel the
touchscreen does work.

The Memsic MXC622X accelerometer at i2c bus 1, addr 0x15 also is not
enabled as there is no driver for it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>