This patch adds Graphics Output Protocol support to the kernel.  UEFI2.0 spec
deprecates Universal Graphics Adapter (UGA) protocol and only Graphics Output
Protocol (GOP) is produced.  Therefore, the boot loader needs to query the
UEFI firmware with appropriate Output Protocol and pass the video information
to the kernel.  As a result of GOP protocol, an EFI framebuffer driver is
needed for displaying console messages.  The patch adds a EFI framebuffer
driver.  The EFI frame buffer driver in this patch is based on the Intel Mac
framebuffer driver.

The ELILO bootloader takes care of passing the video information as
appropriate for EFI firmware.

The framebuffer driver has been tested in i386 kernel and x86_64 kernel on EFI
platform.
Signed-off-by: NChandramouli Narayanan <mouli@linux.intel.com>
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Revert 7eea4364.

Lucy said:

  This patch will work with the 19HS but WILL BREAK all other Keyspan
  adapters.  It will take me a few days to get to looking at a correct fix but
  that keyspan_send_setup(port, 1) (and the '1' is the important part) must
  happen once when the port is first opened.  The cflag can just be set to
  whatever the normal default is for your serial environment.

So revert this again pending the proper fix.

Cc: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Lucy McCoy <lucy@keyspan.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cc: Edgar Hucek <hostmaster@ed-soft.at>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

got this HiSax bootup crash on a "make randconfig" bzImage bootup:

 Calling initcall 0xc0bb1320: HiSax_init+0x0/0x380()
 HiSax: Linux Driver for passive ISDN cards
 HiSax: Version 3.5 (kernel)
 HiSax: Layer1 Revision 2.46.2.5
 HiSax: Layer2 Revision 2.30.2.4
 HiSax: TeiMgr Revision 2.20.2.3
 HiSax: Layer3 Revision 2.22.2.3
 HiSax: LinkLayer Revision 2.59.2.4
 HiSax: Total 1 card defined
 HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
 HiSax: HFC-S driver Rev. 1.10.2.4
 HFCS: defined at 0x500 IRQ 5 HZ 250
 Teles 16.3c: IRQ 5 count 0
 HFCS: resetting card
 Teles 16.3c: IRQ 5 count 0
 Teles 16.3c: IRQ(5) getting no interrupts during init 1
 HFCS: resetting card
 ------------[ cut here ]------------
 kernel BUG at include/linux/timer.h:145!
 invalid opcode: 0000 [#1] PREEMPT DEBUG_PAGEALLOC
 Modules linked in:

 Pid: 1, comm: swapper Not tainted (2.6.24-rc3 #2045)
 EIP: 0060:[<c063afbf>] EFLAGS: 00010286 CPU: 0
 EIP is at hfcs_card_msg+0x15f/0x180
 EAX: c0cf2e5c EBX: 000000f2 ECX: 00000000 EDX: ffff1193
 ESI: f76e8000 EDI: f76e8000 EBP: f7c23ec4 ESP: f7c23eac
  DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
 Process swapper (pid: 1, ti=f7c22000 task=f7c0e000 task.ti=f7c22000)
 Stack: 00000000 f7c23ec4 c011703b 00000002 f76e8000 00000000 f7c23ef8 c060c3e5
        c0a7c9c0 c0a315dc 00000005 00000001 00000000 f7c23f34 00000000 c0b5c9c0
        f7c23f34 00000000 c0f5a8e0 f7c23f80 c0bb154f 00000000 00000001 c0a9b5b9
 Call Trace:
  [<c010339a>] show_trace_log_lvl+0x1a/0x40
  [<c0103469>] show_stack_log_lvl+0xa9/0xe0
  [<c010355f>] show_registers+0xbf/0x200
  [<c01037a4>] die+0x104/0x220
  [<c0103943>] do_trap+0x83/0xc0
  [<c0103ca8>] do_invalid_op+0x88/0xa0
  [<c083621a>] error_code+0x6a/0x70
  [<c060c3e5>] checkcard+0x4a5/0x620
  [<c0bb154f>] HiSax_init+0x22f/0x380
  [<c0b867b7>] kernel_init+0x97/0x2a0
  [<c0102f87>] kernel_thread_helper+0x7/0x20
  =======================
 Code: e8 43 ae ff 8b 57 3c 85 d2 0f 84 ef fe ff ff b8 a0 99 ad c0 b9 02 00 00 00 e8 ce 11 ae ff 83 c4 0c b8 00 00 00 00 5b 5e 5f c9 c3 <0f> 0b eb fe 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90
 EIP: [<c063afbf>] hfcs_card_msg+0x15f/0x180 SS:ESP 0068:f7c23eac
 Kernel panic - not syncing: Attempted to kill init!

The box has no HiSax card installed.

the reason for the crash is add_timer() done on an already running
timer. This happens because for some reason CARD_INIT is called twice.

this patch works this problem around by using mod_timer() - this gets
a booting system - but it would be nice to figure out why CARD_INIT
is done twice.

the ISDN config section (generated via make randconfig) is this:

#
# ISDN feature submodules
#
# CONFIG_ISDN_DRV_LOOP is not set
CONFIG_ISDN_DIVERSION=y

#
# ISDN4Linux hardware drivers
#

#
# Passive cards
#
CONFIG_ISDN_DRV_HISAX=y

#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
CONFIG_HISAX_1TR6=y
CONFIG_HISAX_NI1=y
CONFIG_HISAX_MAX_CARDS=8

#
# HiSax supported cards
#
CONFIG_HISAX_16_0=y
# CONFIG_HISAX_16_3 is not set
# CONFIG_HISAX_TELESPCI is not set
CONFIG_HISAX_S0BOX=y
# CONFIG_HISAX_AVM_A1 is not set
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
CONFIG_HISAX_IX1MICROR2=y
CONFIG_HISAX_DIEHLDIVA=y
# CONFIG_HISAX_ASUSCOM is not set
# CONFIG_HISAX_TELEINT is not set
CONFIG_HISAX_HFCS=y
# CONFIG_HISAX_SEDLBAUER is not set
CONFIG_HISAX_SPORTSTER=y
# CONFIG_HISAX_MIC is not set
# CONFIG_HISAX_NETJET is not set
# CONFIG_HISAX_NETJET_U is not set
# CONFIG_HISAX_NICCY is not set
# CONFIG_HISAX_ISURF is not set
# CONFIG_HISAX_HSTSAPHIR is not set
# CONFIG_HISAX_BKM_A4T is not set
# CONFIG_HISAX_SCT_QUADRO is not set
# CONFIG_HISAX_GAZEL is not set
# CONFIG_HISAX_HFC_PCI is not set
# CONFIG_HISAX_W6692 is not set
# CONFIG_HISAX_HFC_SX is not set
# CONFIG_HISAX_DEBUG is not set

#
# HiSax PCMCIA card service modules
#

#
# HiSax sub driver modules
#
CONFIG_HISAX_ST5481=y
CONFIG_HISAX_HFCUSB=y
# CONFIG_HISAX_HFC4S8S is not set
CONFIG_HISAX_FRITZ_PCIPNP=y
CONFIG_HISAX_HDLC=y

#
# Active cards
#
CONFIG_ISDN_DRV_ICN=m
CONFIG_ISDN_DRV_PCBIT=m
CONFIG_ISDN_DRV_SC=y
# CONFIG_ISDN_DRV_ACT2000 is not set
CONFIG_HYSDN=m
# CONFIG_ISDN_DRV_GIGASET is not set
# CONFIG_ISDN_CAPI is not set
CONFIG_PHONE=y
CONFIG_PHONE_IXJ=m
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Kai Germaschewski <kai@germaschewski.name>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

 - fix lockup when switching from early console to real console
 - make sysrq reliable
 - fix panic, if sysrq is issued before console is opened
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch corrects recently changed (and now invalid) Kconfig descriptions
for the DMA engine framework:

 - Non-Intel(R) hardware also has DMA engines;
 - DMA is used for more than memcpy and RAID offloading.

In fact, on most platforms memcpy and RAID aren't factors, and DMA
exists so that peripherals can transfer data to/from memory while
the CPU does other work.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds an additional loop, that delays turning off the DMA
until the LCDC core has been turned off. This prevents the picture
to be shifted some random length when the kernel re-initializes
the LCDC.

Without this patch, the LCDC keeps running for some small time after the
PWRCON:LCD_PWR has been cleared ; the FIFO suffers an underrun and on
re-starting the LCDC the FIFO data stays shifted.

This behavior has been seen and fixed on AT91SAM9261-EK and two custom
AT91SAM9261 boards, all of them having different LCD panels.

Thanks a lot to Anti Sullin for submitting this patch (long
time ago).
Signed-off-by: NAnti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove errnoeous x character from dev_dbg() call that stops the driver
compiling under debug.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There should be a pci_dev_put when breaking out of a loop that iterates
over calls to pci_get_device and similar functions.

This was fixed using the following semantic patch.

// <smpl>
@@
identifier d;
type T;
expression e;
iterator for_each_pci_dev;
@@

T *d;
...
for_each_pci_dev(d)
   {... when != pci_dev_put(d)
        when != e = d
(
    return d;
|
+  pci_dev_put(d);
?  return ...;
)
...}
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Greg KH <greg@kroah.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The code in fb_ddc_read() is said to be based on the implementation of the
radeon driver:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=fc5891c8a3ba284f13994d7bc1f1bfa8283982de

However, comparing the old radeon driver code with the new fb_ddc code
reveals some differences.  Most notably, the I2C bus lines are held at the
end of the function, while the original code was releasing them (as the
comment above correctly says.)

There are a few other differences, which appear to be responsible for read
failures on my system.  While tracing low-level I2C code in i2c-algo-bit, I
noticed that the initial attempt to read the EDID always failed.  It takes
one retry for the read to succeed.  As we are about to remove this
automatic retry property from i2c-algo-bit, reading the EDID would really
fail.

As a summary, the I2C lines quirk which is supposedly needed to read EDID
on some older monitors is currently breaking the (first) read on all other
monitors (and might not even work with older ones - did anyone try since
October 2006?)

After applying the patch below, which makes the code in fb_ddc_read()
really similar to what the radeon driver used to have, the first EDID read
succeeds again.

On top of that, as it appears that this code has been broken for one year
now and nobody seems to have complained, I'm curious if it makes sense to
keep this quirk in place.  It makes the code more complex and slower just
for the sake of monitors which I guess nobody uses anymore.  Can't we just
get rid of it?
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: NRoger Leigh <rleigh@whinlatter.ukfsn.org>
Tested-by: NMichael Buesch <mb@bu3sch.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

m68k: zorro7xx needs <asm/amigahw.h> if !CONFIG_AMIGA_PCMCIA

Reported by Ingo Juergensmann <ij@2007.bluespice.org>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow passing a bus number through the platform data for the S3C2410 SPI
GPIO driver.   This is needed to support multiple SPI busses.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If we specify an GPIO which cannot be used for the purpose, then assume
that the GPIO is not to be used and do not try and configure it.  This can
be the case where the SPI bus is TX only.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

During the initialization of the TPM TIS driver, the necessary locality has
to be requested earlier in the init-process.  Depending on the used TPM
chip, this leads to wrong information.  For example: Lenovo X61s with Atmel
TPM:

tpm_tis 00:0a: 1.2 TPM (device-id 0xFFFF, rev-id 255)

But correct is:

tpm_tis 00:0c: 1.2 TPM (device-id 0x3203, rev-id 9)

This short patch fixes this issue.
Signed-off-by: NMarcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On some systems the number of resources(IO,MEM) returnedy by PNP device is
greater than the PNP constant, for example motherboard devices.  It brings
that some resources can't be reserved and resource confilicts.  This will
cause PCI resources are assigned wrongly in some systems, and cause hang.
This is a regression since we deleted ACPI motherboard driver and use PNP
system driver.

[akpm@linux-foundation.org: fix text and coding-style a bit]
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- Limit video memory size to avoid crossing a 256 MiB boundary in IOIF space.
- Pass the actual amount of video memory used to lv1_gpu_memory_allocate().
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- vuart.ko -> ps3-vuart.ko
- sys-manager.ko -> ps3-sys-manager.ko
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the atmel_spi driver label GPIOs according to the device for which
they're acting as a chipselect.  This way the debugfs dump of gpio state is
more informative.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

acpiphp.h: not using kernel-doc, so change /** to /*
acpiphp_core.c: lots of kernel-doc cleanups
acpiphp_glue.c: lots of kernel-doc cleanups
acpiphp_ibm.c: lots of kernel-doc cleanups
cpqphp_core.c: lots of kernel-doc cleanups
cpqphp_ctrl.c: lots of kernel-doc cleanups
fakephp.c:  correct kernel-doc notation
pciehp_ctrl.c: correct kernel-doc notation
rpadlpar_core.c: correct function names & kernel-doc notation
rpaphp_core.c: correct kernel-doc notation
shpchp_ctrl.c: correct kernel-doc notation
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix kernel-doc parameter names and ending block comments (change **/
to */).
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NLinas Vepstas <linas@linas.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There should be a pci_dev_put when breaking out of a loop that iterates
over calls to pci_get_device and similar functions.

This was fixed using the following semantic patch.

// <smpl>
@@
identifier d;
type T;
expression e;
iterator for_each_pci_dev;
@@

T *d;
...
for_each_pci_dev(d)
  {... when != pci_dev_put(d)
       when != e = d
(
   return d;
|
+  pci_dev_put(d);
?  return ...;
)
...}
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The pcie protdrv status can be returned uninitialized,
if there are no children under a device. This leads to
bad responses downstream. Fix this.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some CPUs in the S3C24XX series do not support readback of the
value of a pin when the pin has been configured to an IRQ.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If another driver wants to claim the vbus pin, say
to notify the user of an connect/disconnect then allow
the IRQ to be shared by specifiying IRQ_SHARED in the
flags.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixup the fallout from the arch moves earlier in the kernel
series.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>

This patch (as1018) adds an unusual_devs entry for the JetFlash
TS1GJF2A.  This device doesn't like read requests for more than 188
sectors.  Setting max_sectors down to 64 is overkill, but at least
it will work without errors.

For the torturous debugging history, see this thread:

	http://marc.info/?t=118745764700005&r=1&w=2Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A recent patch added software synchronization during EHCI startup,
so ports aren't switched away from the companion controllers after
resets have started.  This patch adds a short delay letting hardware
finish that port switching before any new resets begin ... so both
ends of that hardware race window are closed.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Dave Miller <davem@davemloft.net>
Cc: Dely Sy <dely.l.sy@intel.com>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

to make HAL like the microtek driver's devices the parent must be
correctly set.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1010) was written by both Kay Sievers and me.  It solves
the problem of duplicated keys in USB uevent structures by refactoring
the uevent subroutines, taking advantage of the way the hotplug core
calls uevent handlers for the device's bus and for the device's type.
Keys needed for both USB-device and USB-interface events are added in
usb_uevent(), which is the bus handler.  Keys appropriate only for
USB-device or USB-interface events are added in usb_dev_uevent() or
usb_if_uevent() respectively, the type handlers.

In addition, unnecessary tests for NULL pointers are removed as are
duplicated debugging log statements.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1009) solves the problem of multiple registrations for
USB sysfs files in a more satisfying way than the existing code.  It
simply adds a flag to keep track of whether or not the files have been
created; that way the files can be created or removed as needed.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>

Per the maintainer of the usbserial/sierra.c driver, the patch below adds
a new id to the list of supported cards for the sierra driver. Tested and
working for me on Fedora 8, kernel 2.6.23 and on the more recent sierra.c
available in
http://www.sierrawireless.com/resources/support/Software/Linux/v.1.2.6b(kernel2.6.21).zip

Hardware is a MiniPCI card in a Lenovo T61p.
Signed-off-by: NAndrew Gilmore <agilmore@wirelessbeehive.com>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Arnd Bergmann wrote:

usb_hcd_flush_endpoint() has a retry loop that starts with a spin_lock_irq(),
but only gives up the spinlock, not the irq_disable before jumping to the
rescan label.

Alan Stern:

I agree with your sentiment, but it would be better to solve this
problem without using local_irq_disable().
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Another one in the "ok, this is trivial to fix" list... :-)

[PATCH] fix directory references in usb/README
Signed-off-by: NDirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a resubmission of the patch to upgrade the unusual_devs.h file to
support an older firmware revision of the Nikon D200. This patch includes the
requested /proc/bus/usb/devices information.

T:  Bus=01 Lev=01 Prnt=01 Port=09 Cnt=02 Dev#=  6 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=04b0 ProdID=040f Rev= 1.00
S:  Manufacturer=NIKON
S:  Product=NIKON DSC D200
S:  SerialNumber=0000000
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: NMike Pagano <mpagano@gentoo.org>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Two main issues fixed here are:
 - An improper use of in-struct lock to protect an open count
 - Use of urb status for -EINPROGRESS

Also, along the way:
 - Change usb_unlink_urb to usb_kill_urb. Apparently there's no need
   to use usb_unlink_urb whatsoever in this driver, and the old use of
   usb_kill_urb was outright racy (it unlinked and immediately freed).
 - Fix indentation in adu_write. Looks like it was damaged by a script.
 - Vitaly wants -EBUSY on multiply opens.
 - bInterval was taken from a wrong endpoint.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NVitaliy Ivanov <vitalivanov@gmail.com>
Tested-by: NVitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In commit acd2a847 usb_serial_generic_write()
disables interrupts when taking &port->lock which is also taken in
usb_serial_generic_read_bulk_callback() resulting in an inconsistent lock state
due to the latter not disabling interrupts on the local cpu. Fix that by
disabling interrupts in the latter call site also.
Signed-off-by: NBorislav Petkov <bbpetkov@yahoo.de>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usbled has a race where show methods for attributes in sysfs can
follow a NULL pointer during disconnect. The correct ordering fixes
it.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Free buffer when writing ZLP_REG5 failed
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes priority mistakes similar to '!x & y'
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1000) sets the SCSI allow_restart flag for USB disk
devices.  In theory this should never hurt, and there definitely are
devices out there (such as the Seagate 250-GB external drive) which
need the flag to be set.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>