Create a cache of devices that are seen in a system. This will avoid
the unnecessary traversal of the device list in the scsi_dh when there
are multiple luns of a same type.
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

multipath keeps a separate device table which may be
more current than the built-in one.
So we should make sure to always call ->attach whenever
a multipath map with hardware handler is instantiated.
And we should call ->detach on removal, too.

[sekharan: update as per comments from agk]
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch updates the RDAC device handler to
refuse to attach to devices not supporting the
RDAC vpd pages.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch updates the hp_sw device handler to properly
check the return codes etc.
And adds the 'correct' machine definitions.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch converts the EMC device handler to use a proper
state machine. We now also parse the extended INQUIRY
information to determine if long trespass commands are
supported. And we're now using the long trespass command
correctly. And finally there's now an check at init time
to refuse to attach to devices not supporting EMC-specific
VPD pages.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Implement a 'dh_state' sdev attribute for dynamic device handler
manipulation. A read on the attribute will return the name of
the currently attached device handler or 'detached' if no handler
is attached.
The attribute allows the following strings to be written:
- The name of the device handler to be attached if the state is
  'detached'.
- 'activate' to trigger path activation if a device handler
  is attached.
- 'detach' to detach the currently attached device handler.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Instead of having each and every driver implement its own
device table scanning code we should rather implement a common
routine and scan the device tables there.
This allows us also to implement a general notifier chain
callback for all device handler instead for one per handler.

[sekharan: Fix rejections caused by conflicting bug fix]
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Daniel Debonzi reports that he has managed to wrap host_no.  Increasing
the number of host numbers available to 32-bit from 16-bit allows the
problem to be evaded for another hundred years.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Update index allocation as follows.

* sd_index_idr is used only for ID allocation and mapping
  functionality is not used.  Use more memory efficient ida instead.

* idr and ida have their own locks inside them and don't need them for
  operation.  Drop it.

* index wasn't freed if probing failed after index allocation.  fix
  it.

* ida allocation should be repeated if it fails with -EAGAIN.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

When drivers use a shared tag map we can end up with more requests
than tags, because the tag map is shost->can_queue tags and there
can be sdevs * sdev->queue_depth requests. In scsi_request_fn
if tag allocation fails we just drop down to just dequeueing the
tag without a tag. The problem is that drivers using the shared tag
map rely on a valid tag always being set, because it will use the
tag number to lookup commands later.

This patch has us check if we got a valid tag when the host lock
is held right before we check if the host queue is ready. We do the
check here because to allocate the tag we need the q lock, but
if the tag is bad we want to add the device/q onto the starved list
which requires the host lock.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We want to set the queue depth to something reasonable - not
the can_queue.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Ed Lin <ed.lin@promise.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We want to set the queue depth to something reasonable - not
the can_queue.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Currently qla4xxx and stex pass in their can_queue values into
scsi_activate_tcq because they wanted the tag map that large.
The problem with this is that it ends up also setting the queue
depth to that large value. All we want to do this in this case
is set the device queue depth and the other device settings.
We do not need to touch the tag map sizing because the drivers
had setup that map according to their can_queue limits when the
shared map was created.

The scsi mid layer in request_fn will then handle the case where we
have more requests than available tags when it checks the host
queue ready function.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Mike Christie noticed a bogus memset. It can be removed as dead code
since the number of bytes in the driver buffer in fixed block mode is
always a multiple of the tape block size.
Signed-off-by: NKai Mäkisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Move buffer pointer back when data could not be written. Bug found by
Mike Christie.
Signed-off-by: NKai Mäkisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Use the full buffer size available, as there's no reason to limit
the firwmare-image load-segment size for these parts.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Add an additional check to verify that the current executing
firmware is in fact non-ROM code.  The non-ROM Get-ID mailbox
command is used for verification.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Total ram words can exceed a 16bit value on large-memory boards.
Safely extend to a 32bit width.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Firmware does not have the facilities to issue management server
IOCBs.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

There were several issues here, one, during RSCN handling if a
follow-on RSCN occurred (within interrupt context) the DPC thread
could inadvertantly leave the fcport in a stale lost state.
Secondly, scheduled rport removal is handled exclusively by the
'parent' DPC thread, so wake up the proper thread.  Finally,
process vport loop-resync's only when the vport has in an
"active" state (ID acquired).
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

By allowing the qla2x00_alert_all_vps() to manage per-vport
recognition of the MBA.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

All fcport->state management should be done within
qla2x00_mark_device_lost(), the assignment of state within
qla2x00_mark_vp_devices_dead() caused associated rports to not be
removed.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

While issuing a marker, manipulating the request/response queues
and modifying the outstanding command array.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The firmware group has suggested that FCE (Fibre Channel Event)
tracing be enabled prior to EFT (Extended Firmware Tracing) to
maximize the capturing of data on the wire.  This change has no
real semantic effect on driver operation, as it's mostly a
shuffling of code.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Recent ISPs have this information written at manufacturing time,
so use the information.  This also reduces future churn of the
qla_devtbl.h file contents, as the driver can now depend on the
information to be present in VPD.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

iIDMA support requires the driver issue several additional
fabric-managegment (FM) commands per port discovered during SNS
scanning -- GFPN (Get Fabric Port Name) and GPSC (Get Port Speed
Capabilities).  It has been found during testing that some
switches do not respond as *well* as expected to these commands
(silence -- no ACC nor BS_RJT).  So, to handle such conditions,
allow the user the ability to indirectly disable the FM commands
by disabling iIDMA with the ql2xiidmaenable module-parameter.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Removed repeated or unnecessary operations during vport
creation/deletion.
Signed-off-by: NShyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NRavi Anand <ravi.anand@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This parameter counts the total number of ISP aborts during
driver execution.  The value is exported through a DEVICE_ATTR()
off the scsi_host.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

As there's no point in adding a fixed-fudge value (originally 5
seconds), honor the user settings only.  We also remove the
driver's dead-callback get_rport_dev_loss_tmo function
(qla2x00_get_rport_loss_tmo()).
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Commit 2c96d8d0 pushed the
acquisition of hardware_lock to too fine a level, which in turn
will cause problems with cond_resched()s added with
40a2e34a.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The new code in commit 5cbf1565
has a bug in the version supporting the AMD 'syscall' instruction.
It clobbers the user's %ecx register value (with the %ebp value).

This change fixes it.
Signed-off-by: NRoland McGrath <roland@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  ipsec: ipcomp - Decompress into frags if necessary
  ipsec: ipcomp - Merge IPComp implementations
  pkt_sched: Fix locking in shutdown_scheduler_queue()

Compile error on other architectures:

    CC      drivers/mfd/tc6393xb.o
  /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/mfd/tc6393xb.c: In function ‘tc6393xb_attach_irq’:
  /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/mfd/tc6393xb.c:324: error: implicit declaration of function ‘set_irq_flags’
  ...
Reported-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Fix boot problem due to AT_BASE_PLATFORM change

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc: Wire up new system calls.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Wire up new system calls