Hardware is the same as MaxMedia UB425-TC but ships with a different
remote.
Signed-off-by: NJakob Haufe <sur5r@sur5r.net>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx is oopsing with some DVB devices:

[10856.061884] general protection fault: 0000 [#1] SMP
[10856.067041] Modules linked in: rc_hauppauge em28xx_rc xc5000 drxk em28xx_dvb dvb_core em28xx videobuf2_vmalloc videobuf2_memops videobuf2_core rc_pixelview_new tuner_xc2028 tuner cx8800 cx88xx tveeprom btcx_risc videobuf_dma_sg videobuf_core rc_core v4l2_common videodev ebtable_nat ebtables nf_conntrack_ipv4 nf_defrag_ipv4 xt_CHECKSUM be2iscsi iscsi_boot_sysfs iptable_mangle bnx2i cnic uio cxgb4i cxgb4 tun bridge cxgb3i cxgb3 stp ip6t_REJECT mdio libcxgbi nf_conntrack_ipv6 llc nf_defrag_ipv6 ib_iser rdma_cm ib_addr xt_conntrack iw_cm ib_cm ib_sa nf_conntrack ib_mad ib_core bnep bluetooth iscsi_tcp libiscsi_tcp ip6table_filter libiscsi ip6_tables scsi_transport_iscsi xfs libcrc32c snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep snd_seq snd_seq_device snd_pcm tg3 snd_page_alloc snd_timer
[10856.139176]  snd ptp iTCO_wdt soundcore pps_core iTCO_vendor_support lpc_ich mfd_core coretemp nfsd hp_wmi crc32c_intel microcode serio_raw rfkill sparse_keymap nfs_acl lockd sunrpc kvm_intel kvm uinput binfmt_misc firewire_ohci nouveau mxm_wmi i2c_algo_bit drm_kms_helper firewire_core crc_itu_t ttm drm i2c_core wmi [last unloaded: dib0070]
[10856.168969] CPU 1
[10856.170799] Pid: 13606, comm: dvbv5-zap Not tainted 3.9.0-rc5+ #26 Hewlett-Packard HP Z400 Workstation/0AE4h
[10856.181187] RIP: 0010:[<ffffffffa0459e47>]  [<ffffffffa0459e47>] em28xx_write_regs_req+0x37/0x1c0 [em28xx]
[10856.191028] RSP: 0018:ffff880118401a58  EFLAGS: 00010282
[10856.196533] RAX: 00020000012d0000 RBX: ffff88010804aec8 RCX: ffff880118401b14
[10856.203852] RDX: 0000000000000048 RSI: 0000000000000000 RDI: ffff88010804aec8
[10856.211174] RBP: ffff880118401ac8 R08: 0000000000000001 R09: 0000000000000000
[10856.218496] R10: 0000000000000000 R11: 0000000000000006 R12: 0000000000000048
[10856.226026] R13: ffff880118401b14 R14: ffff88011752b258 R15: ffff88011752b258
[10856.233352] FS:  00007f26636d2740(0000) GS:ffff88011fc20000(0000) knlGS:0000000000000000
[10856.241626] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[10856.247565] CR2: 00007f2663716e20 CR3: 00000000c7eb1000 CR4: 00000000000007e0
[10856.254889] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[10856.262215] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[10856.269542] Process dvbv5-zap (pid: 13606, threadinfo ffff880118400000, task ffff8800cd625d40)
[10856.278340] Stack:
[10856.280564]  ffff88011ffe8de8 0000000000000002 0000000000000000 ffff88011ffe9b00
[10856.288191]  ffff880118401b14 00ff88011ffe9b08 ffff880100000048 ffffffff8112a52a
[10856.295893]  0000000000000001 ffff88010804aec8 0000000000000048 ffff880118401b14
[10856.303521] Call Trace:
[10856.306182]  [<ffffffff8112a52a>] ? __alloc_pages_nodemask+0x15a/0x960
[10856.312912]  [<ffffffffa045a002>] em28xx_write_regs+0x32/0xa0 [em28xx]
[10856.319638]  [<ffffffffa045a221>] em28xx_write_reg+0x21/0x30 [em28xx]
[10856.326279]  [<ffffffffa045a2cc>] em28xx_gpio_set+0x9c/0x100 [em28xx]
[10856.332919]  [<ffffffffa045a3ac>] em28xx_set_mode+0x7c/0x80 [em28xx]
[10856.339472]  [<ffffffffa03ef032>] em28xx_dvb_bus_ctrl+0x32/0x40 [em28xx_dvb]

This is caused by commit c7a45e5b,
that added support for two I2C buses. A partial fix was applied
at 3de09fbb, but it doesn't cover
all cases, as the DVB core fills fe->dvb->priv with adapter->priv.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

[mchehab@redhat.com: Fix a merge conflict]
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/usb/dvb-usb-v2/anysee.c: In function ‘anysee_frontend_attach’:
drivers/media/usb/dvb-usb-v2/anysee.c:641: warning: ‘ret’ may be used uninitialized in this function
And gcc is right (see the ANYSEE_HW_507T case), so initialize ret to zero
to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: save isoc endpoint number for DVB only if endpoint has alt settings with xMaxPacketSize != 0

X-Patchwork-Delegate: mchehab@redhat.com
In addition to commit 72cc9ba3 "em28xx: ignore isoc DVB USB endpoints with
wMaxPacketSize = 0 bytes for all alt settings" we should not save the endpoint
number of the isoc DVB endpoint before it has been validated.
While the current code works fine, dev->dvb_ep_isoc != 0 could be interpreted
as indicator that the device provides DVB support.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The intend of this patch is to improve the support of the dib7090 and
dib7790. The AGC1 min value is set to 32768 by default. The actual AGC1 min
and the external attenuation are controled depending on the received RF
level.
Signed-off-by: NOlivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The intend of this patch is to remove the support for the dib7090E. The
DiB7090E-package has never left prototype state and never made it to
mass-prod-state.
Signed-off-by: NOlivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The intend of this patch is to improve the support of the dib8096. The PLL
parameters are not automatically computed. The limit to set/unset external
diode for attenuation has been updated. The TFE8096P board is using the
new I2C API.
Signed-off-by: NOlivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The intend of this patch is to improve the support of the dib8000.
Signed-off-by: NOlivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

commit 61ff5d69 "em28xx: improve em2710/em2820 distinction" missed the
le16_to_cpu conversion of the USB vendor ID.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now that we can get the strength from r820t, use it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: NAntti Palosaari <crope@iki.fi>

This tuner is used on some rtl2882 dongles. Add it to the driver.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: NAntti Palosaari <crope@iki.fi>

There are three drivers with *it913x name on it, and they all
belong to the same device:
	a tuner, at it913x.c;
	a frontend: it913x-fe.c;
	a bridge: it913x.c, renamed to dvb_usb_it913x by the
building system.

This is confusing. Even more confusing are the two .c files with
the same name under different directories, with different contents
and different functions. So, prepend the tuner one.

This also breaks the out-of-tree compilation system.
Reported-by: NFrederic Fays <frederic.fays@gmail.com>
Acked-by: NAntti Palosaari <crope@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Commit cd634f1b ("[media] v4l2: put VIDIOC_DBG_G_CHIP_NAME under
ADV_DEBUG") missed the initializer of radio_ioctl_ops:
drivers/media/usb/em28xx/em28xx-video.c:1830:2: error: unknown field 'vidioc_g_chip_info' specified in initializer
drivers/media/usb/em28xx/em28xx-video.c:1830:26: error: 'vidioc_g_chip_info' undeclared here (not in a function)
Signed-off-by: NMichal Marek <mmarek@suse.cz>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Map RC_MAP_REDDO to that device.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Chip id 18 is used by the em2710 and em2820.
The current code assumes that if the device is a camera, the chip is an em2710
and an em2820 otherwise.
But it turned out that the em2820 is also used in camera devices.
"Silvercrest 1.3 MPix" webcams for example are available with both chips.
Fortunately both variants are using different generic USD IDs which give us a
hint about the used chip.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The snapshot button support is currently broken, because module em28xx-rc is
loaded only if the device has remote control support.
Fix it by also loading this module if the device has a snapshot button.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Both MythTV and gstreamer expect that they can set/get/query/enumerate the
standards, even if the input is the component input for which standards
really do not apply.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is the latest firmware version and - it seems - the most reliable.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Video nodes can be used at once after registration, so make sure the full
initialization is done before registering them.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- return EBUSY instead of EAGAIN.
- add missing break.
- remove unnecessary buf type check (done by the core).
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This prepares the driver for priority and control event handling.
This patch also checks for correct streaming ownership and it makes a
small improvement to the encoder_cmd ioctls: always zero 'flags' and
drop the memset of 'raw' as that is already done by the v4l2 core.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

dvb->adapter.priv should also be set to the i2c bus since that's what
em28xx_tuner_callback expects.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This ioctl will be extended to return more information than just the name.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Only enable this ioctl if the VIDEO_ADV_DEBUG config option is set. This
prevents abuse from both userspace and kernelspace (some bridge drivers
abuse DBG_G_CHIP_IDENT, lets prevent that from happening again with this
ioctl).
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

"enum dmx_ts_pes" and "typedef enum dmx_pes_type_t" are just the
same enum declared twice, since Kernel (2.6.12). There's no reason
to duplicate it there, and sparse complains about that:
	drivers/media/dvb-core/dmxdev.c:600:55: warning: mixing different enum types
So, remove the internal define, keeping just the external one.
Internally, use only "enum dmx_ts_pes", as it is too late to drop
dmx_pes_type_t from the userspace API.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/usb/dvb-usb/m920x.c:91:6: warning: "ret" may be used uninitialized in this function [-Wuninitialized]
drivers/media/usb/dvb-usb/m920x.c:70:6: note: "ret" was declared here
This is real, if a remote control has an empty initialization sequence
we would get success or failure randomly.
OTOH the initialization of ret in m920x_init is needless, the function
returns with an error as soon as an error happens, so the last return
can only be a success and we can hard-code 0 there.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx: fix typo in scale_to_size().
The second hscale should be vscale. This bug caused xawtv to fail because it
cannot find a workable image size.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Loading the cypress firmware is not dvb specific and should be common
functionality. Move the source to media/common and make it a standalone
module.
As a result we can remove the dependency on dvb-usb in go7007, which has
nothing to do with dvb.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The et61x251 driver was removed in v3.5. Remove the last references to
its Kconfig macro now.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This sensor is used by the "SpeedLink Vicious And Devine Laplace webcam" and
others. It supports resolutions up to 1600x1200 (at 7-8 fps), but for
resolutions higher than 640x480, further driver changes will be necessary,
such as sensor output resolution switching (including further configuration
changes), bridge xclk adjustment and disabling of 16 bit (12 bit) output formats
at high resolutions. Image quality should also needs to be improved.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Windows driver also probes at least two further i2c addresses (0x22 >> 1
and 0x66 >> 1). I've got some hints that they are very likely used by Samsung
and Kodak sensors, which are known to be used in Empia devices, too.
We havn't seen any devices using these sensors yet and don't know how to probe
them properly, so leave a comment.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

OmniVision sensors are used as well in Empiatech based cameras such as the
"SpeedLink Vicious And Devine Laplace" webcam (EM2765 + Omnivision OV2640).
With this patch applied, OminiVision sensors with 8 bit address and register
width are detected (recent models have a 16 bit address width and use different
client addresses).
The most commonly used sensors (including the ones listed by Empiatech) are
detected properly, although there is no support for them yet.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Other sensors like the ones from OmniVision need a different probing procedure,
so it makes sense have separate functions for each manufacturer/sensor type.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add further Micron chip IDs to be able to identify all Micron sensors listed
by Empiatech.
Also probe the two alternate i2c addresses used by Micron sensors with 8 bit
address and 16 bit register width.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>