As of June 2012 it uses the same firmware as the Hauppauge WinTV HVR 930C.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert radio-sf16fmi to use generic LM7000 driver.
Tested with SF16-FMI, SF16-FMP and SF16-FMD.

radio.");
@@ -48,37 +50,40 @@ struct fmi
 	bool mute;
 	unsigned long curfreq; /* freq in kHz */
 	struct mutex lock;
+	struct lm7000 lm;
 };

 static struct fmi fmi_card;
 static struct pnp_dev *dev;
 bool pnp_attached;

-/* freq is in 1/16 kHz to internal number, hw precision is 50 kHz */
-/* It is only useful to give freq in interval of 800 (=0.05Mhz),
- * other bits will be truncated, e.g 92.7400016 -> 92.7, but
- * 92.7400017 -> 92.75
- */
-#define RSF16_ENCODE(x)	((x) / 800 + 214)
 #define RSF16_MINFREQ (87 * 16000)
 #define RSF16_MAXFREQ (108 * 16000)

-static void outbits(int bits, unsigned int data, int io)
+#define FMI_BIT_TUN_CE		(1 << 0)
+#define FMI_BIT_TUN_CLK		(1 << 1)
+#define FMI_BIT_TUN_DATA	(1 << 2)
+#define FMI_BIT_VOL_SW		(1 << 3)
+#define FMI_BIT_TUN_STRQ	(1 << 4)
+
+void fmi_set_pins(struct lm7000 *lm, u8 pins)
 {
-	while (bits--) {
-		if (data & 1) {
-			outb(5, io);
-			udelay(6);
-			outb(7, io);
-			udelay(6);
-		} else {
-			outb(1, io);
-			udelay(6);
-			outb(3, io);
-			udelay(6);
-		}
-		data >>= 1;
-	}
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert radio-aimslab to use generic LM7000 driver.
Tested with Reveal RA300.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add very simple driver for Sanyo LM7000 AM/FM tuner chip. Only FM is supported
as there is no known HW with AM implemented.

This will be used by radio-aimslab and radio-sf16fmi.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There is a specific header sound/ac97_codec.h that defines these.
All drivers should use it instead of rolling its own set of macros.
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

And fix initial control setup.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This driver allowed only one open filehandle. This is against the spec, so
fix the driver by assigning proper ownership when streaming.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Implement struct v4l2_device: use the core lock and use the v4l2_device
release() callback.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Embed the video_device struct instead of allocating it and register it as
the last thing in probe().
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Set the new capability flags in G_TUNER and return ENODATA if no channels
were found.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Update the spec with the new capabilities and specify new error codes for
S_HW_FREQ_SEEK.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tell the application whether the hardware seek is bounded and/or wraps around.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The V4L2 spec says reporting mono and stereo at the same time means
the hardware can not distinguish between the two. So when we can,
we should report only one of them.
Signed-off-by: NDaniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Many of the audio decoders handled by the driver support this mode,
so the driver should support it as well.

Coding style errors are done to blend into the surrounding code.
Signed-off-by: NDaniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L2 specifies the audio mode to use for combinations of possible
(rxsubchans) and requested (audmode) audio modes. Up to now tvaudio
has made these decisions automatically based on the possible audio
modes from setting of the frequency until VIDIOC_S_TUNER was called.
It then forced the hardware to use the mode requested by the user.
With this patch it continues to adjust the audio mode while taking
the requested mode into account.
Signed-off-by: NDaniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The V4L2_TUNER_MODE_* constants are not suited for use in bitfields.
Signed-off-by: NDaniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Judging from the data sheet it will automatically switch to the next
best audio mode in accordance with the V4L2 tuner audio matrix.
Signed-off-by: NDaniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is never read and only assigned 0.
Signed-off-by: NDaniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As V4L2_TUNER_MODE_SAP == V4L2_TUNER_MODE_LANG2, we make
V4L2_TUNER_MODE_LANG1 equal to V4L2_TUNER_MODE_STEREO.
Signed-off-by: NDaniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The passed audio mode is not a bitfield.
Signed-off-by: NDaniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

These constants were unused so far but need | instead of &.
Signed-off-by: NDaniel Glöckner <daniel-gl@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In function fops_open variable type was set but not used. Tested by compilation only.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Acked-by: NMichael Hunold <michael@mihu.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The test here is never true because '&' was used instead of '|'.  It was
the same as:

	if (status & ((1<<16) & (1<<17)) ...
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It should be a mistake due to copy & paste in header file
  Correct it in videobuf2-dma-config.h for avoiding duplicate include it

Change-Id: I1f71fcec2889c033c7db380c58d9a1369c5afb35
Signed-off-by: NAlbert Wang <twang13@marvell.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For one, the driver device pointer needs to be filled in, or the lirc core
will refuse to load the driver. And we really need to wire up all the
platform_device bits. This has been tested via the lirc sourceforge tree
and verified to work, been sitting there for months, finally getting
around to sending it. :\

CC: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

stb0899_read_ber() takes 500ms (half a second!) to deliver the current
BER value. Apparently it takes 5 subsequent readings, with a 100ms pause
between them (and even before the first one). This is a real performance
brake if an application freqeuently reads the BER of several devices.
The attached patch reduces this to a single reading, with no more pausing.
I didn't observe any negative side effects of this change.
Signed-off-by: NKlaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NVolokh Konstantin <volokh84@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixes the following sparse warnings:

drivers/media/video/s5p-fimc/fimc-lite-reg.c:218:6: warning: symbol
'flite_hw_set_out_order' was not declared. Should it be static?

drivers/media/video/s5p-fimc/fimc-mdevice.c:183:5: warning: symbol '__fimc_pipeline_shutdown' was not declared. Should it be static?
drivers/media/video/s5p-fimc/fimc-mdevice.c:1013:12: warning: symbol 'fimc_md_init' was not declared. Should it be static?
drivers/media/video/s5p-fimc/fimc-mdevice.c:1024:13: warning: symbol 'fimc_md_exit' was not declared. Should it be static?

drivers/media/video/s5p-fimc/fimc-core.c:466:5: warning: symbol 'fimc_set_color_effect' was not declared. Should it be static?

drivers/media/video/s5p-fimc/fimc-capture.c:1163:5: warning: symbol 'enclosed_rectangle' was not declared. Should it be static?
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Sparse complains if about using unsigned long.
videobuf-dma-contig.c:47:67: warning: restricted gfp_t degrades to integer
videobuf-dma-contig.c:47:65: warning: incorrect type in argument 2 (different base types)
videobuf-dma-contig.c:47:65:    expected restricted gfp_t [usertype] gfp_mask
videobuf-dma-contig.c:47:65:    got unsigned long
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Hans de Goede accepted to be the new gspca maintainer.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Patch id 6016af82 ("[media] v4l2: use __u32
rather than enums in ioctl() structs") unintentionally changes the type of
the format field in struct v4l2_create_buffers from struct v4l2_format to
__u32. Revert that change.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>