When not active the hardware should be able to tolerate voltages within
the normal operating range so when removing set the maximum voltage we
can use to the maximum rather than minimum of the operating range. This
will improve interoperability in case we end up sharing the supply in
some design.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAnji jonnala <anjir@codeaurora.org>
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Implement good battery algorithm defined in the battery charging V1.2 spec
for detecting different charging ports.  USB hardware is put into low power
mode when connected to a dedicated charging port.  vbus_draw and set_power
methods are implemented for determining the allowed current from Host in
different states (un-configured/suspend/configured).

The charger block is implemented using vendor specific registers and the
PHY used in MSM8960(28nm PHY) different from older targets like MSM8x60
and MSM7x30(45nm PHY).  The PHY vendor and product id registers are not
implemented in the above chipsets.  Hence PHY type is passed via platform
data.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

HSUSB core clock is derived from daytona fabric clock and for
HSUSB operational require minimum core clock at 55MHz. Since, HSUSB
cannot tolerate daytona fabric clock change in the middle of HSUSB
operational, vote for maximum Daytona fabric clock
while usb is operational
Signed-off-by: NAnji jonnala <anjir@codeaurora.org>
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The current code is clearing in_lpm flag after enabling the IRQ.
If IRQ comes immediately before in_lpm flag is set, it thinks that
hardware is in low power mode and disables the IRQ.  Fix this by
clearing in_lpm flag before enabling the IRQ.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver is used across all MSM SoCs.  Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The driver private data is retrieved incorrectly which results
a crash when written into "mode" debugfs file.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the below compiler warning

drivers/usb/otg/msm72k_otg.c:257: warning: 'msm_otg_suspend' defined but not used
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Implement runtime and system pm ops to put hardware into low power
mode (LPM). As part of LPM, USB clocks are turned off, PHY is put
into suspend state and PHY comparators are turned off if VBUS/Id
notifications are not required from PHY.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver implements PHY initialization, clock management, ULPI IO ops
and simple OTG state machine to kick host/peripheral based on Id/VBUS
line status.  VBUS/Id lines are tied to a reference voltage on some boards.
Hence provide debugfs interface to select host/peripheral mode.
Signed-off-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>