- 04 4月, 2013 1 次提交
-
-
由 Manjunathappa, Prakash 提交于
Adds device tree support for davinci_mmc. Also add binding documentation. As of now tested for non-dma PIO mode and without GPIO card_detect/ write_protect option because of dependencies on EDMA and GPIO module DT support. Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com> Reviewed-by: NMark Rutland <mark.rutland@arm.com> Tested-by: NSekhar Nori <nsekhar@ti.com> Cc: linux-mmc@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: davinci-linux-open-source@linux.davincidsp.com Cc: devicetree-discuss@lists.ozlabs.org Cc: cjb@laptop.org Cc: Sekhar Nori <nsekhar@ti.com> Cc: mporter@ti.com Cc: Arnd Bergmann <arnd@arndb.de> Acked-by: NArnd Bergmann <arnd@arndb.de> Acked-by: NChris Ball <cjb@laptop.org> Signed-off-by: NSekhar Nori <nsekhar@ti.com>
-
- 03 4月, 2013 4 次提交
-
-
Add tps6507x regulator device tree data to da850-evm by adding regulator consumers with tightened constraints and regulator-name.TPS6507x regulator handle can be obtained by using this regulator name. Regulator constraints are added as per da850 board file. Regulator names are given as per maximum output voltage the regulator is capable to provide. for e.g. regulator name for dcdc1 is "VDCDC1_3.3V". Also, add tps6507x PMIC I2C slave device under I2C0 node. Tested on da850-evm. Signed-off-by: NVishwanathrao Badarkhe, Manish <manishv.b@ti.com> Signed-off-by: NSekhar Nori <nsekhar@ti.com>
-
Add device tree data for tps6507x regulator by adding all tps6507x regulator nodes. Regulators are initialized based on compatible name provided in tps6507x DT file. All tps6507x PMIC regulator device tree nodes are placed in a separate device tree include file (tps6507x.dtsi). tps6507x.dtsi file is created using datasheet http://www.ti.com/lit/ds/symlink/tps65070.pdf Tested on da850-evm. Signed-off-by: NVishwanathrao Badarkhe, Manish <manishv.b@ti.com> Signed-off-by: NSekhar Nori <nsekhar@ti.com>
-
由 Paul Bolle 提交于
The DaVinci debugging macro contains a check for CONFIG_DEBUG_DAVINCI_DA8XX_UART0. But there's no corresponding Kconfig symbol, so this test will always evaluate to false. That Kconfig symbol is not needed because, as __arch_decomp_setup() shows, there are no DaVinci DA8XX boards that use UART0 for debugging. We can remove two lines of unneeded code. Signed-off-by: NPaul Bolle <pebolle@tiscali.nl> Signed-off-by: NSekhar Nori <nsekhar@ti.com>
-
由 Manjunathappa, Prakash 提交于
Remove specifying mmc controller IP version information via platform data, instead specify device name so that driver derives it from platform_device_id table. Also change the clock node name to match the changed dev_id. Tested on da850-evm to make sure driver loads without clk_get failures. Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com> Reviewed-by: NSekhar Nori <nsekhar@ti.com> Acked-by: NArnd Bergmann <arnd@arndb.de> Acked-by: NChris Ball <cjb@laptop.org> Signed-off-by: NSekhar Nori <nsekhar@ti.com>
-
- 01 4月, 2013 7 次提交
-
-
由 Philip Avinash 提交于
Add ECAP and EHRPWM module clock nodes. Also add a clock node for TBCLK for EHRWPM. Signed-off-by: NPhilip Avinash <avinashphilip@ti.com> Signed-off-by: NSekhar Nori <nsekhar@ti.com>
-
由 Philip Avinash 提交于
DaVinci clock implementation does not support clock enable/disable functionality on non-PSC clock nodes. On DA850 SoC, EHRPWM module requires support for enable/disable of TBCLK controlled using a system module register. This patch adds a method for enabling/disabling non-PSC clocks into DaVinci clock implementation. Signed-off-by: NPhilip Avinash <avinashphilip@ti.com> Signed-off-by: NSekhar Nori <nsekhar@ti.com>
-
由 Linus Torvalds 提交于
-
git://git.infradead.org/users/vkoul/slave-dma由 Linus Torvalds 提交于
Pull slave-dmaengine fixes from Vinod Koul: "Two fixes for slave-dmaengine. The first one is for making slave_id value correct for dw_dmac and the other one fixes the endieness in DT parsing" * 'fixes' of git://git.infradead.org/users/vkoul/slave-dma: dw_dmac: adjust slave_id accordingly to request line base dmaengine: dw_dma: fix endianess for DT xlate function
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media由 Linus Torvalds 提交于
Pull media fixes from Mauro Carvalho Chehab: "For a some fixes for Kernel 3.9: - subsystem build fix when VIDEO_DEV=y, VIDEO_V4L2=m and I2C=m - compilation fix for arm multiarch preventing IR_RX51 to be selected - regression fix at bttv crop logic - s5p-mfc/m5mols/exynos: a few fixes for cameras on exynos hardware" * 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: [media] [REGRESSION] bt8xx: Fix too large height in cropcap [media] fix compilation with both V4L2 and I2C as 'm' [media] m5mols: Fix bug in stream on handler [media] s5p-fimc: Do not attempt to disable not enabled media pipeline [media] s5p-mfc: Fix encoder control 15 issue [media] s5p-mfc: Fix frame skip bug [media] s5p-fimc: send valid m2m ctx to fimc_m2m_job_finish [media] exynos-gsc: send valid m2m ctx to gsc_m2m_job_finish [media] fimc-lite: Fix the variable type to avoid possible crash [media] fimc-lite: Initialize 'step' field in fimc_lite_ctrl structure [media] ir: IR_RX51 only works on OMAP2
-
git://git.kernel.dk/linux-block由 Linus Torvalds 提交于
Pull block fixes from Jens Axboe: "Alright, this time from 10K up in the air. Collection of fixes that have been queued up since the merge window opened, hence postponed until later in the cycle. The pull request contains: - A bunch of fixes for the xen blk front/back driver. - A round of fixes for the new IBM RamSan driver, fixing various nasty issues. - Fixes for multiple drives from Wei Yongjun, bad handling of return values and wrong pointer math. - A fix for loop properly killing partitions when being detached." * tag 'for-linus-20130331' of git://git.kernel.dk/linux-block: (25 commits) mg_disk: fix error return code in mg_probe() rsxx: remove unused variable rsxx: enable error return of rsxx_eeh_save_issued_dmas() block: removes dynamic allocation on stack Block: blk-flush: Fixed indent code style cciss: fix invalid use of sizeof in cciss_find_cfgtables() loop: cleanup partitions when detaching loop device loop: fix error return code in loop_add() mtip32xx: fix error return code in mtip_pci_probe() xen-blkfront: remove frame list from blk_shadow xen-blkfront: pre-allocate pages for requests xen-blkback: don't store dev_bus_addr xen-blkfront: switch from llist to list xen-blkback: fix foreach_grant_safe to handle empty lists xen-blkfront: replace kmalloc and then memcpy with kmemdup xen-blkback: fix dispatch_rw_block_io() error path rsxx: fix missing unlock on error return in rsxx_eeh_remap_dmas() Adding in EEH support to the IBM FlashSystem 70/80 device driver block: IBM RamSan 70/80 error message bug fix. block: IBM RamSan 70/80 branding changes. ...
-
由 Paul Walmsley 提交于
This reverts commit 6aa97070. Commit 6aa97070 ("lockdep: check that no locks held at freeze time") causes problems with NFS root filesystems. The failures were noticed on OMAP2 and 3 boards during kernel init: [ BUG: swapper/0/1 still has locks held! ] 3.9.0-rc3-00344-ga937536b #1 Not tainted ------------------------------------- 1 lock held by swapper/0/1: #0: (&type->s_umount_key#13/1){+.+.+.}, at: [<c011e84c>] sget+0x248/0x574 stack backtrace: rpc_wait_bit_killable __wait_on_bit out_of_line_wait_on_bit __rpc_execute rpc_run_task rpc_call_sync nfs_proc_get_root nfs_get_root nfs_fs_mount_common nfs_try_mount nfs_fs_mount mount_fs vfs_kern_mount do_mount sys_mount do_mount_root mount_root prepare_namespace kernel_init_freeable kernel_init Although the rootfs mounts, the system is unstable. Here's a transcript from a PM test: http://www.pwsan.com/omap/testlogs/test_v3.9-rc3/20130317194234/pm/37xxevm/37xxevm_log.txt Here's what the test log should look like: http://www.pwsan.com/omap/testlogs/test_v3.8/20130218214403/pm/37xxevm/37xxevm_log.txt Mailing list discussion is here: http://lkml.org/lkml/2013/3/4/221 Deal with this for v3.9 by reverting the problem commit, until folks can figure out the right long-term course of action. Signed-off-by: NPaul Walmsley <paul@pwsan.com> Cc: Mandeep Singh Baines <msb@chromium.org> Cc: Jeff Layton <jlayton@redhat.com> Cc: Shawn Guo <shawn.guo@linaro.org> Cc: <maciej.rutecki@gmail.com> Cc: Fengguang Wu <fengguang.wu@intel.com> Cc: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ben Chan <benchan@chromium.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Tejun Heo <tj@kernel.org> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 31 3月, 2013 1 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending由 Linus Torvalds 提交于
Pull SCSI target fixes from Nicholas Bellinger: "This includes the bug-fix for a >= v3.8-rc1 regression specific to iscsi-target persistent reservation conflict handling (CC'ed to stable), and a tcm_vhost patch to drop VIRTIO_RING_F_EVENT_IDX usage so that in-flight qemu vhost-scsi-pci device code can detect the proper vhost feature bits. Also, there are two more tcm_vhost patches still being discussed by MST and Asias for v3.9 that will be required for the in-flight qemu vhost-scsi-pci device patch to function properly, and that should (hopefully) be the last target fixes for this round." * git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
-
- 30 3月, 2013 8 次提交
-
-
由 Andy Shevchenko 提交于
On some hardware configurations we have got the request line with the offset. The patch introduces convert_slave_id() helper for that cases. The request line base is came from the driver data provided by the platform_device_id table. Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: NViresh Kumar <viresh.kumar@linaro.org> Signed-off-by: NVinod Koul <vinod.koul@intel.com>
-
由 Arnd Bergmann 提交于
As reported by Wu Fengguang's build robot tracking sparse warnings, the dma_spec arguments in the dw_dma_xlate are already byte swapped on little-endian platforms and must not get swapped again. This code is currently not used anywhere, but will be used in Linux 3.10 when the ARM SPEAr platform starts using the generic DMA DT binding. Signed-off-by: NArnd Bergmann <arnd@arndb.de> Reported-by: NFengguang Wu <fengguang.wu@intel.com> Acked-by: NViresh Kumar <viresh.kumar@linaro.org> Signed-off-by: NVinod Koul <vinod.koul@intel.com>
-
由 Rafael J. Wysocki 提交于
The Adam Belay's e-mail address in MAINTAINERS under PNP SUPPORT is not valid any more and I started to maintain that code in the meantime as a matter of fact, so list myself as a maintainer of it along with Bjorn and remove the Adam's entry from it. Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client由 Linus Torvalds 提交于
Pull ceph fix from Sage Weil: "This fixes a regression introduced during the last merge window when mapping non-existent images." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: rbd: don't zero-fill non-image object requests
-
由 Alex Elder 提交于
A result of ENOENT from a read request for an object that's part of an rbd image indicates that there is a hole in that portion of the image. Similarly, a short read for such an object indicates that the remainder of the read should be interpreted a full read with zeros filling out the end of the request. This behavior is not correct for objects that are not backing rbd image data. Currently rbd_img_obj_request_callback() assumes it should be done for all objects. Change rbd_img_obj_request_callback() so it only does this zeroing for image objects. Encapsulate that special handling in its own function. Add an assertion that the image object request is a bio request, since we assume that (and we currently don't support any other types). This resolves a problem identified here: http://tracker.ceph.com/issues/4559 The regression was introduced by bf0d5f50. Reported-by: NDan van der Ster <dan@vanderster.com> Signed-off-by: NAlex Elder <elder@inktank.com> Reviewed-off-by: NSage Weil <sage@inktank.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs由 Linus Torvalds 提交于
Pull btrfs fixes from Chris Mason: "We've had a busy two weeks of bug fixing. The biggest patches in here are some long standing early-enospc problems (Josef) and a very old race where compression and mmap combine forces to lose writes (me). I'm fairly sure the mmap bug goes all the way back to the introduction of the compression code, which is proof that fsx doesn't trigger every possible mmap corner after all. I'm sure you'll notice one of these is from this morning, it's a small and isolated use-after-free fix in our scrub error reporting. I double checked it here." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: Btrfs: don't drop path when printing out tree errors in scrub Btrfs: fix wrong return value of btrfs_lookup_csum() Btrfs: fix wrong reservation of csums Btrfs: fix double free in the btrfs_qgroup_account_ref() Btrfs: limit the global reserve to 512mb Btrfs: hold the ordered operations mutex when waiting on ordered extents Btrfs: fix space accounting for unlink and rename Btrfs: fix space leak when we fail to reserve metadata space Btrfs: fix EIO from btrfs send in is_extent_unchanged for punched holes Btrfs: fix race between mmap writes and compression Btrfs: fix memory leak in btrfs_create_tree() Btrfs: fix locking on ROOT_REPLACE operations in tree mod log Btrfs: fix missing qgroup reservation before fallocating Btrfs: handle a bogus chunk tree nicely Btrfs: update to use fs_state bit
-
由 Len Brown 提交于
Commit 3e7fc708 ("ia64 idle: delete pm_idle") in 3.9-rc1 didn't finish the job, leaving an un-initialized reference to (*idle)(). [ Haven't seen a crash from this - but seems like we are just being lucky that "idle" is zero so it does get initialized before we jump to randomland - Len ] Reported-by: NLars-Peter Clausen <lars@metafoo.de> Signed-off-by: NLen Brown <len.brown@intel.com> Signed-off-by: NTony Luck <tony.luck@intel.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc由 Linus Torvalds 提交于
Pull arc architecture fixes from Vineet Gupta: "This includes fix for a serious bug in DMA mapping API, make allyesconfig wreckage, removal of bogus email-list placeholder in MAINTAINERS, a typo in ptrace helper code and last remaining changes for syscall ABI v3 which we are finally starting to transition-to internally. The request is late than I intended to - but I was held up with debugging a timer link list corruption, for which a proposed fix to generic timer code was sent out to lkml/tglx earlier today." * 'for-curr' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: ARC: Fix the typo in event identifier flags used by ptrace arc: fix dma_address assignment during dma_map_sg() ARC: Remove SET_PERSONALITY (tracks cross-arch change) ARC: ABIv3: fork/vfork wrappers not needed in "no-legacy-syscall" ABI ARC: ABIv3: Print the correct ABI ver ARC: make allyesconfig build breakages ARC: MAINTAINERS update for ARC
-
- 29 3月, 2013 14 次提交
-
-
由 Josef Bacik 提交于
A user reported a panic where we were panicing somewhere in tree_backref_for_extent from scrub_print_warning. He only captured the trace but looking at scrub_print_warning we drop the path right before we mess with the extent buffer to print out a bunch of stuff, which isn't right. So fix this by dropping the path after we use the eb if we need to. Thanks, Cc: stable@vger.kernel.org Signed-off-by: NJosef Bacik <jbacik@fusionio.com> Signed-off-by: NChris Mason <chris.mason@fusionio.com>
-
由 Nicholas Bellinger 提交于
This patch fixes a regression introduced in v3.8-rc1 code where a failed target_check_reservation() check in target_setup_cmd_from_cdb() was causing an incorrect SAM_STAT_GOOD status to be returned during a WRITE operation performed by an unregistered / unreserved iscsi initiator port. This regression is only effecting iscsi-target due to a special case check for TCM_RESERVATION_CONFLICT within iscsi_target_erl1.c:iscsit_execute_cmd(), and was still correctly disallowing WRITE commands from backend submission for unregistered / unreserved initiator ports, while returning the incorrect SAM_STAT_GOOD status due to the missing SAM_STAT_RESERVATION_CONFLICT assignment. This regression was first introduced with: commit de103c93 Author: Christoph Hellwig <hch@lst.de> Date: Tue Nov 6 12:24:09 2012 -0800 target: pass sense_reason as a return value Go ahead and re-add the missing SAM_STAT_RESERVATION_CONFLICT assignment during a target_check_reservation() failure, so that iscsi-target code sends the correct SCSI status. All other fabrics using target_submit_cmd_*() with a RESERVATION_CONFLICT call to transport_generic_request_failure() are not effected by this bug. Reported-by: NJeff Leung <jleung@curriegrad2004.ca> Cc: Christoph Hellwig <hch@lst.de> Cc: <stable@vger.kernel.org> Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>
-
由 Nicholas Bellinger 提交于
This patch adds a VHOST_SCSI_FEATURES mask minus VIRTIO_RING_F_EVENT_IDX so that vhost-scsi-pci userspace will strip this feature bit once GET_FEATURES reports it as being unsupported on the host. This is to avoid a bug where ->handle_kicks() are missed when EVENT_IDX is enabled by default in userspace code. (mst: Rename to VHOST_SCSI_FEATURES + add comment) Acked-by: NMichael S. Tsirkin <mst@redhat.com> Reviewed-by: NAsias He <asias@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>
-
由 Michel Lespinasse 提交于
This reverts commit 18693050 ("mm: introduce VM_POPULATE flag to better deal with racy userspace programs"). VM_POPULATE only has any effect when userspace plays racy games with vmas by trying to unmap and remap memory regions that mmap or mlock are operating on. Also, the only effect of VM_POPULATE when userspace plays such games is that it avoids populating new memory regions that get remapped into the address range that was being operated on by the original mmap or mlock calls. Let's remove VM_POPULATE as there isn't any strong argument to mandate a new vm_flag. Signed-off-by: NMichel Lespinasse <walken@google.com> Signed-off-by: NHugh Dickins <hughd@google.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb由 Linus Torvalds 提交于
Pull USB fixes from Greg Kroah-Hartman: "Here are some USB fixes to resolve issues reported recently, as well as a new device id for the ftdi_sio driver." * tag 'usb-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD usb: Fix compile error by selecting USB_OTG_UTILS USB: serial: fix hang when opening port USB: EHCI: fix bug in iTD/siTD DMA pool allocation xhci: Don't warn on empty ring for suspended devices. usb: xhci: Fix TRB transfer length macro used for Event TRB. usb/acpi: binding xhci root hub usb port with ACPI usb: add find_raw_port_number callback to struct hc_driver() usb: xhci: fix build warning
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty由 Linus Torvalds 提交于
Pull TTY/serial fixes from Greg Kroah-Hartman: "Here are some tty/serial driver fixes for 3.9. The big thing here is the fix for the huge mess we caused renaming the 8250 driver accidentally in the 3.7 kernel release, without realizing that there were users of the module options that suddenly broke. This is now resolved, and, to top the injury off, we have a backwards- compatible option for those users who got used to the new name since 3.7. Ugh, sorry about that. Other than that, some other minor fixes for issues that have been reported by users." * tag 'tty-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: Xilinx: ARM: UART: clear pending irqs before enabling irqs TTY: 8250, deprecated 8250_core.* options TTY: 8250, revert module name change serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection tty: atmel_serial_probe(): index of atmel_ports[] fix
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging由 Linus Torvalds 提交于
Pull staging driver fixes from Greg Kroah-Hartman: "Here are two tiny staging driver fixes to resolve issues that have been reported." * tag 'staging-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: comedi: s626: fix continuous acquisition staging: zcache: fix typo "64_BIT"
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core由 Linus Torvalds 提交于
Pull sysfs fixes from Greg Kroah-Hartman: "Here are two fixes for sysfs that resolve issues that have been found by the Trinity fuzz tool, causing oopses in sysfs. They both have been in linux-next for a while to ensure that they do not cause any other problems." * tag 'driver-core-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: sysfs: handle failure path correctly for readdir() sysfs: fix race between readdir and lseek
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc由 Linus Torvalds 提交于
Pull char/misc driver fixes from Greg Kroah-Hartman: "Here are some small char/misc driver fixes that resolve issues recently reported against the 3.9-rc kernels. All have been in linux-next for a while." * tag 'char-misc-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: VMCI: Fix process-to-process DRGAMs. mei: ME hardware reset needs to be synchronized mei: add mei_stop function to stop mei device extcon: max77693: Initialize register of MUIC device to bring up it without platform data extcon: max77693: Fix bug of wrong pointer when platform data is not used extcon: max8997: Check the pointer of platform data to protect null pointer error
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm由 Linus Torvalds 提交于
Pull ACPI and power management fixes from Rafael J Wysocki: - Fix for a recent cpufreq regression related to acpi-cpufreq and suspend/resume from Viresh Kumar. - cpufreq stats reference counting fix from Viresh Kumar. - intel_pstate driver fixes from Dirk Brandewie and Konrad Rzeszutek Wilk. - New ACPI suspend blacklist entry for Sony Vaio VGN-FW21M from Fabio Valentini. - ACPI Platform Error Interface (APEI) fix from Chen Gong. - PCI root bridge hotplug locking fix from Yinghai Lu. * tag 'pm+acpi-3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: PCI / ACPI: hold acpi_scan_lock during root bus hotplug ACPI / APEI: fix error status check condition for CPER ACPI / PM: fix suspend and resume on Sony Vaio VGN-FW21M cpufreq: acpi-cpufreq: Don't set policy->related_cpus from .init() cpufreq: stats: do cpufreq_cpu_put() corresponding to cpufreq_cpu_get() intel-pstate: Use #defines instead of hard-coded values. cpufreq / intel_pstate: Fix calculation of current frequency cpufreq / intel_pstate: Add function to check that all MSRs are valid
-
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6由 Linus Torvalds 提交于
Pull crypto fixes from Herbert Xu: "This removes IPsec ESN support from the talitos/caam drivers since they were implemented incorrectly, causing interoperability problems if ESN is used with them." * git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: Revert "crypto: caam - add IPsec ESN support" Revert "crypto: talitos - add IPsec ESN support"
-
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64由 Linus Torvalds 提交于
Pull arm64 fix from Catalin Marinas: "Fix IS_ENABLED() usage typo (missing CONFIG_ prefix)." * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64: ARM64: early_printk: Fix check for CONFIG_ARM64_64K_PAGES
-
git://gitorious.org/linux-omap-dss2/linux由 Linus Torvalds 提交于
Pull fbdev fixes from Tomi Valkeinen: "Since Florian is still away/inactive, I volunteered to collect fbdev fixes for 3.9 and changes for 3.10. I didn't receive any other fbdev fixes than OMAP yet, but I didn't want to delay this further as there's a compilation fix for OMAP1. So there could be still some fbdev fixes on the way a bit later. This contains: - Fix OMAP1 compilation - OMAP display fixes" * tag 'fbdev-fixes-3.9-rc4' of git://gitorious.org/linux-omap-dss2/linux: omapdss: features: fix supported outputs for OMAP4 OMAPDSS: tpo-td043 panel: fix data passing between SPI/DSS parts omapfb: fix broken build on OMAP1
-
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace由 Linus Torvalds 提交于
Pull userns fixes from Eric W Biederman: "The bulk of the changes are fixing the worst consequences of the user namespace design oversight in not considering what happens when one namespace starts off as a clone of another namespace, as happens with the mount namespace. The rest of the changes are just plain bug fixes. Many thanks to Andy Lutomirski for pointing out many of these issues." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: userns: Restrict when proc and sysfs can be mounted ipc: Restrict mounting the mqueue filesystem vfs: Carefully propogate mounts across user namespaces vfs: Add a mount flag to lock read only bind mounts userns: Don't allow creation if the user is chrooted yama: Better permission check for ptraceme pid: Handle the exit of a multi-threaded init. scm: Require CAP_SYS_ADMIN over the current pidns to spoof pids.
-
- 28 3月, 2013 5 次提交
-
-
由 Konstantin Holoborodko 提交于
It enhances the driver for FTDI-based USB serial adapters to recognize Mitsubishi Electric Corp. USB/RS422 Converters as FT232BM chips and support them. https://search.meau.com/?q=FX-USB-AWSigned-off-by: NKonstantin Holoborodko <klh.kernel@gmail.com> Tested-by: NKonstantin Holoborodko <klh.kernel@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Wei Yongjun 提交于
Fix to return a negative error code from the error handling case instead of 0, as returned elsewhere in this function. Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn> Reviewed-by: NJingoo Han <jg1.han@samsung.com> Signed-off-by: NJens Axboe <axboe@kernel.dk>
-
由 Miao Xie 提交于
If we don't find the expected csum item, but find a csum item which is adjacent to the specified extent, we should return -EFBIG, or we should return -ENOENT. But btrfs_lookup_csum() return -EFBIG even the csum item is not adjacent to the specified extent. Fix it. Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com> Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
-
由 Miao Xie 提交于
We reserve the space for csums only when we write data into a file, in the other cases, such as tree log, log replay, we don't do reservation, so we can use the reservation of the transaction handle just for the former. And for the latter, we should use the tree's own reservation. But the function - btrfs_csum_file_blocks() didn't differentiate between these two types of the cases, fix it. Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com> Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
-
由 Wang Shilong 提交于
The function btrfs_find_all_roots is responsible to allocate memory for 'roots' and free it if errors happen,so the caller should not free it again since the work has been done. Besides,'tmp' is allocated after the function btrfs_find_all_roots, so we can return directly if btrfs_find_all_roots() fails. Signed-off-by: NWang Shilong <wangsl-fnst@cn.fujitsu.com> Reviewed-by: NMiao Xie <miaox@cn.fujitsu.com> Reviewed-by: NJan Schmidt <list.btrfs@jan-o-sch.net> Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
-