This reverts commits 5c9d2d5c, c7da82b8, and e7fe7b5c.

We'll probably need to revisit this, but basically we should not
complicate the get_user_pages_fast() case, and checking the actual page
table protection key bits will require more care anyway, since the
protection keys depend on the exact state of the VM in question.

Particularly when doing a "remote" page lookup (ie in somebody elses VM,
not your own), you need to be much more careful than this was.  Dave
Hansen says:

 "So, the underlying bug here is that we now a get_user_pages_remote()
  and then go ahead and do the p*_access_permitted() checks against the
  current PKRU. This was introduced recently with the addition of the
  new p??_access_permitted() calls.

  We have checks in the VMA path for the "remote" gups and we avoid
  consulting PKRU for them. This got missed in the pkeys selftests
  because I did a ptrace read, but not a *write*. I also didn't
  explicitly test it against something where a COW needed to be done"

It's also not entirely clear that it makes sense to check the protection
key bits at this level at all.  But one possible eventual solution is to
make the get_user_pages_fast() case just abort if it sees protection key
bits set, which makes us fall back to the regular get_user_pages() case,
which then has a vma and can do the check there if we want to.

We'll see.

Somewhat related to this all: what we _do_ want to do some day is to
check the PAGE_USER bit - it should obviously always be set for user
pages, but it would be a good check to have back.  Because we have no
generic way to test for it, we lost it as part of moving over from the
architecture-specific x86 GUP implementation to the generic one in
commit e585513b ("x86/mm/gup: Switch GUP to the generic
get_user_page_fast() implementation").

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The 'access_permitted' helper is used in the gup-fast path and goes
beyond the simple _PAGE_RW check to also:

 - validate that the mapping is writable from a protection keys
   standpoint

 - validate that the pte has _PAGE_USER set since all fault paths where
   pmd_write is must be referencing user-memory.

Link: http://lkml.kernel.org/r/151043111049.2842.15241454964150083466.stgit@dwillia2-desk3.amr.corp.intel.comSigned-off-by: NDan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Every pagevec_init user claims the pages being released are hot even in
cases where it is unlikely the pages are hot.  As no one cares about the
hotness of pages being released to the allocator, just ditch the
parameter.

No performance impact is expected as the overhead is marginal.  The
parameter is removed simply because it is a bit stupid to have a useless
parameter copied everywhere.

Link: http://lkml.kernel.org/r/20171018075952.10627-6-mgorman@techsingularity.netSigned-off-by: NMel Gorman <mgorman@techsingularity.net>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

During truncation, the mapping has already been checked for shmem and
dax so it's known that workingset_update_node is required.

This patch avoids the checks on mapping for each page being truncated.
In all other cases, a lookup helper is used to determine if
workingset_update_node() needs to be called.  The one danger is that the
API is slightly harder to use as calling workingset_update_node directly
without checking for dax or shmem mappings could lead to surprises.
However, the API rarely needs to be used and hopefully the comment is
enough to give people the hint.

sparsetruncate (tiny)
                              4.14.0-rc4             4.14.0-rc4
                             oneirq-v1r1        pickhelper-v1r1
Min          Time      141.00 (   0.00%)      140.00 (   0.71%)
1st-qrtle    Time      142.00 (   0.00%)      141.00 (   0.70%)
2nd-qrtle    Time      142.00 (   0.00%)      142.00 (   0.00%)
3rd-qrtle    Time      143.00 (   0.00%)      143.00 (   0.00%)
Max-90%      Time      144.00 (   0.00%)      144.00 (   0.00%)
Max-95%      Time      147.00 (   0.00%)      145.00 (   1.36%)
Max-99%      Time      195.00 (   0.00%)      191.00 (   2.05%)
Max          Time      230.00 (   0.00%)      205.00 (  10.87%)
Amean        Time      144.37 (   0.00%)      143.82 (   0.38%)
Stddev       Time       10.44 (   0.00%)        9.00 (  13.74%)
Coeff        Time        7.23 (   0.00%)        6.26 (  13.41%)
Best99%Amean Time      143.72 (   0.00%)      143.34 (   0.26%)
Best95%Amean Time      142.37 (   0.00%)      142.00 (   0.26%)
Best90%Amean Time      142.19 (   0.00%)      141.85 (   0.24%)
Best75%Amean Time      141.92 (   0.00%)      141.58 (   0.24%)
Best50%Amean Time      141.69 (   0.00%)      141.31 (   0.27%)
Best25%Amean Time      141.38 (   0.00%)      140.97 (   0.29%)

As you'd expect, the gain is marginal but it can be detected.  The
differences in bonnie are all within the noise which is not surprising
given the impact on the microbenchmark.

radix_tree_update_node_t is a callback for some radix operations that
optionally passes in a private field.  The only user of the callback is
workingset_update_node and as it no longer requires a mapping, the
private field is removed.

Link: http://lkml.kernel.org/r/20171018075952.10627-3-mgorman@techsingularity.netSigned-off-by: NMel Gorman <mgorman@techsingularity.net>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch only affects users of mmu_notifier->invalidate_range callback
which are device drivers related to ATS/PASID, CAPI, IOMMUv2, SVM ...
and it is an optimization for those users.  Everyone else is unaffected
by it.

When clearing a pte/pmd we are given a choice to notify the event under
the page table lock (notify version of *_clear_flush helpers do call the
mmu_notifier_invalidate_range).  But that notification is not necessary
in all cases.

This patch removes almost all cases where it is useless to have a call
to mmu_notifier_invalidate_range before
mmu_notifier_invalidate_range_end.  It also adds documentation in all
those cases explaining why.

Below is a more in depth analysis of why this is fine to do this:

For secondary TLB (non CPU TLB) like IOMMU TLB or device TLB (when
device use thing like ATS/PASID to get the IOMMU to walk the CPU page
table to access a process virtual address space).  There is only 2 cases
when you need to notify those secondary TLB while holding page table
lock when clearing a pte/pmd:

  A) page backing address is free before mmu_notifier_invalidate_range_end
  B) a page table entry is updated to point to a new page (COW, write fault
     on zero page, __replace_page(), ...)

Case A is obvious you do not want to take the risk for the device to write
to a page that might now be used by something completely different.

Case B is more subtle. For correctness it requires the following sequence
to happen:
  - take page table lock
  - clear page table entry and notify (pmd/pte_huge_clear_flush_notify())
  - set page table entry to point to new page

If clearing the page table entry is not followed by a notify before setting
the new pte/pmd value then you can break memory model like C11 or C++11 for
the device.

Consider the following scenario (device use a feature similar to ATS/
PASID):

Two address addrA and addrB such that |addrA - addrB| >= PAGE_SIZE we
assume they are write protected for COW (other case of B apply too).

[Time N] -----------------------------------------------------------------
CPU-thread-0  {try to write to addrA}
CPU-thread-1  {try to write to addrB}
CPU-thread-2  {}
CPU-thread-3  {}
DEV-thread-0  {read addrA and populate device TLB}
DEV-thread-2  {read addrB and populate device TLB}
[Time N+1] ---------------------------------------------------------------
CPU-thread-0  {COW_step0: {mmu_notifier_invalidate_range_start(addrA)}}
CPU-thread-1  {COW_step0: {mmu_notifier_invalidate_range_start(addrB)}}
CPU-thread-2  {}
CPU-thread-3  {}
DEV-thread-0  {}
DEV-thread-2  {}
[Time N+2] ---------------------------------------------------------------
CPU-thread-0  {COW_step1: {update page table point to new page for addrA}}
CPU-thread-1  {COW_step1: {update page table point to new page for addrB}}
CPU-thread-2  {}
CPU-thread-3  {}
DEV-thread-0  {}
DEV-thread-2  {}
[Time N+3] ---------------------------------------------------------------
CPU-thread-0  {preempted}
CPU-thread-1  {preempted}
CPU-thread-2  {write to addrA which is a write to new page}
CPU-thread-3  {}
DEV-thread-0  {}
DEV-thread-2  {}
[Time N+3] ---------------------------------------------------------------
CPU-thread-0  {preempted}
CPU-thread-1  {preempted}
CPU-thread-2  {}
CPU-thread-3  {write to addrB which is a write to new page}
DEV-thread-0  {}
DEV-thread-2  {}
[Time N+4] ---------------------------------------------------------------
CPU-thread-0  {preempted}
CPU-thread-1  {COW_step3: {mmu_notifier_invalidate_range_end(addrB)}}
CPU-thread-2  {}
CPU-thread-3  {}
DEV-thread-0  {}
DEV-thread-2  {}
[Time N+5] ---------------------------------------------------------------
CPU-thread-0  {preempted}
CPU-thread-1  {}
CPU-thread-2  {}
CPU-thread-3  {}
DEV-thread-0  {read addrA from old page}
DEV-thread-2  {read addrB from new page}

So here because at time N+2 the clear page table entry was not pair with a
notification to invalidate the secondary TLB, the device see the new value
for addrB before seing the new value for addrA.  This break total memory
ordering for the device.

When changing a pte to write protect or to point to a new write protected
page with same content (KSM) it is ok to delay invalidate_range callback
to mmu_notifier_invalidate_range_end() outside the page table lock.  This
is true even if the thread doing page table update is preempted right
after releasing page table lock before calling
mmu_notifier_invalidate_range_end

Thanks to Andrea for thinking of a problematic scenario for COW.

[jglisse@redhat.com: v2]
  Link: http://lkml.kernel.org/r/20171017031003.7481-2-jglisse@redhat.com
Link: http://lkml.kernel.org/r/20170901173011.10745-1-jglisse@redhat.comSigned-off-by: NJérôme Glisse <jglisse@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alistair Popple <alistair@popple.id.au>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

PMD faults on a zero length file on a file system mounted with -o dax
will not generate SIGBUS as expected.

	fd = open(...O_TRUNC);
	addr = mmap(NULL, 2*1024*1024, PROT_READ|PROT_WRITE, MAP_SHARED, fd, 0);
	*addr = 'a';
        <expect SIGBUS>

The problem is this code in dax_iomap_pmd_fault:

	max_pgoff = (i_size_read(inode) - 1) >> PAGE_SHIFT;

If the inode size is zero, we end up with a max_pgoff that is way larger
than 0.  :)  Fix it by using DIV_ROUND_UP, as is done elsewhere in the
kernel.

I tested this with some simple test code that ensured that SIGBUS was
received where expected.

Cc: <stable@vger.kernel.org>
Fixes: 642261ac ("dax: add struct iomap based DAX PMD support")
Signed-off-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

While reviewing whether MAP_SYNC should strengthen its current guarantee
of syncing writes from the initiating process to also include
third-party readers observing dirty metadata, Dave pointed out that the
check of IOMAP_WRITE is misplaced.

The policy of what to with IOMAP_F_DIRTY should be separated from the
generic filesystem mechanism of reporting dirty metadata. Move this
policy to the fs-dax core to simplify the per-filesystem iomap handlers,
and further centralize code that implements the MAP_SYNC policy. This
otherwise should not change behavior, it just makes it easier to change
behavior in the future.
Reviewed-by: NJan Kara <jack@suse.cz>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: NDave Chinner <david@fromorbit.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Implement a function that filesystems can call to finish handling of
synchronous page faults. It takes care of syncing appropriare file range
and insertion of page table entry.
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Add a flag to iomap interface informing the caller that inode needs
fdstasync(2) for returned extent to become persistent and use it in DAX
fault code so that we don't map such extents into page tables
immediately. Instead we propagate the information that fdatasync(2) is
necessary from dax_iomap_fault() with a new VM_FAULT_NEEDDSYNC flag.
Filesystem fault handler is then responsible for calling fdatasync(2)
and inserting pfn into page tables.
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Currently we dirty radix tree entry whenever dax_insert_mapping_entry()
gets called for a write fault. With synchronous page faults we would
like to insert clean radix tree entry and dirty it only once we call
fdatasync() and update page tables to save some unnecessary cache
flushing. Add 'dirty' argument to dax_insert_mapping_entry() for that.
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

For synchronous page fault dax_iomap_fault() will need to return PFN
which will then need to be inserted into page tables after fsync()
completes. Add necessary parameter to dax_iomap_fault().
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Add missing argument description.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

dax_pmd_insert_mapping() has only one callsite and we will need to
further fine tune what it does for synchronous faults. Just inline it
into the callsite so that we don't have to pass awkward bools around.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

dax_insert_mapping() has only one callsite and we will need to further
fine tune what it does for synchronous faults. Just inline it into the
callsite so that we don't have to pass awkward bools around.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

There are already two users and more are coming.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

There are already two users and more are coming.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Factor out code to get pfn out of iomap that is shared between PTE and
PMD fault path.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

dax_insert_mapping() has lots of arguments and a lot of them is actuall
duplicated by passing vm_fault structure as well. Change the function to
take the same arguments as dax_pmd_insert_mapping().
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Replace iomap->blkno, the sector number, with iomap->addr, the disk
offset in bytes.  For invalid disk offsets, use the special value
IOMAP_NULL_ADDR instead of IOMAP_NULL_BLOCK.

This allows to use iomap for mappings which are not block aligned, such
as inline data on ext4.
Signed-off-by: NAndreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>  # iomap, xfs
Reviewed-by: NJan Kara <jack@suse.cz>

Commit abebfbe2 ("dm: add ->flush() dax operation support") is
buggy. A DM device may be composed of multiple underlying devices and
all of them need to be flushed. That commit just routes the flush
request to the first device and ignores the other devices.

It could be fixed by adding more complex logic to the device mapper. But
there is only one implementation of the method pmem_dax_ops->flush - that
is pmem_dax_flush() - and it calls arch_wb_cache_pmem(). Consequently, we
don't need the pmem_dax_ops->flush abstraction at all, we can call
arch_wb_cache_pmem() directly from dax_flush() because dax_dev->ops->flush
can't ever reach anything different from arch_wb_cache_pmem().

It should be also pointed out that for some uses of persistent memory it
is needed to flush only a very small amount of data (such as 1 cacheline),
and it would be overkill if we go through that device mapper machinery for
a single flushed cache line.

Fix this by removing the pmem_dax_ops->flush abstraction and call
arch_wb_cache_pmem() directly from dax_flush(). Also, remove the device
mapper code that forwards the flushes.

Fixes: abebfbe2 ("dm: add ->flush() dax operation support")
Cc: stable@vger.kernel.org
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Reviewed-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

dax_pmd_insert_mapping() contains the following code:

        pfn_t pfn;
        if (bdev_dax_pgoff(bdev, sector, size, &pgoff) != 0)
            goto fallback;
        /* ... */
    fallback:
      trace_dax_pmd_insert_mapping_fallback(inode, vmf, length, pfn, ret);

When the condition in the if statement fails, the function calls
trace_dax_pmd_insert_mapping_fallback() with an uninitialized pfn value.

This issue has been found while building the kernel with clang.  The
compiler reported:

    fs/dax.c:1280:6: error: variable 'pfn' is used uninitialized
    whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
        if (bdev_dax_pgoff(bdev, sector, size, &pgoff) != 0)
            ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    fs/dax.c:1310:60: note: uninitialized use occurs here
      trace_dax_pmd_insert_mapping_fallback(inode, vmf, length, pfn, ret);
                                                                     ^~~

Link: http://lkml.kernel.org/r/20170903083000.587-1-nicolas.iooss_linux@m4x.orgSigned-off-by: NNicolas Iooss <nicolas.iooss_linux@m4x.org>
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use ~PG_PMD_COLOUR in dax_entry_waitqueue() instead of open coding an
equivalent page offset mask.

Link: http://lkml.kernel.org/r/20170822222436.18926-2-ross.zwisler@linux.intel.comSigned-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: "Slusarz, Marcin" <marcin.slusarz@intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a comment explaining how the user addresses provided to read(2) and
write(2) are validated in the DAX I/O path.

We call dax_copy_from_iter() or copy_to_iter() on these without calling
access_ok() first in the DAX code, and there was a concern that the user
might be able to read/write to arbitrary kernel addresses with this
path.

Link: http://lkml.kernel.org/r/20170816173615.10098-1-ross.zwisler@linux.intel.comSigned-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that we no longer insert struct page pointers in DAX radix trees the
page cache code no longer needs to know anything about DAX exceptional
entries.  Move all the DAX exceptional entry definitions from dax.h to
fs/dax.c.

Link: http://lkml.kernel.org/r/20170724170616.25810-6-ross.zwisler@linux.intel.comSigned-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: NJan Kara <jack@suse.cz>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that we no longer insert struct page pointers in DAX radix trees we
can remove the special casing for DAX in page_cache_tree_insert().

This also allows us to make dax_wake_mapping_entry_waiter() local to
fs/dax.c, removing it from dax.h.

Link: http://lkml.kernel.org/r/20170724170616.25810-5-ross.zwisler@linux.intel.comSigned-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: NJan Kara <jack@suse.cz>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When servicing mmap() reads from file holes the current DAX code
allocates a page cache page of all zeroes and places the struct page
pointer in the mapping->page_tree radix tree.

This has three major drawbacks:

1) It consumes memory unnecessarily. For every 4k page that is read via
   a DAX mmap() over a hole, we allocate a new page cache page. This
   means that if you read 1GiB worth of pages, you end up using 1GiB of
   zeroed memory. This is easily visible by looking at the overall
   memory consumption of the system or by looking at /proc/[pid]/smaps:

	7f62e72b3000-7f63272b3000 rw-s 00000000 103:00 12   /root/dax/data
	Size:            1048576 kB
	Rss:             1048576 kB
	Pss:             1048576 kB
	Shared_Clean:          0 kB
	Shared_Dirty:          0 kB
	Private_Clean:   1048576 kB
	Private_Dirty:         0 kB
	Referenced:      1048576 kB
	Anonymous:             0 kB
	LazyFree:              0 kB
	AnonHugePages:         0 kB
	ShmemPmdMapped:        0 kB
	Shared_Hugetlb:        0 kB
	Private_Hugetlb:       0 kB
	Swap:                  0 kB
	SwapPss:               0 kB
	KernelPageSize:        4 kB
	MMUPageSize:           4 kB
	Locked:                0 kB

2) It is slower than using a common zero page because each page fault
   has more work to do. Instead of just inserting a common zero page we
   have to allocate a page cache page, zero it, and then insert it. Here
   are the average latencies of dax_load_hole() as measured by ftrace on
   a random test box:

    Old method, using zeroed page cache pages:	3.4 us
    New method, using the common 4k zero page:	0.8 us

   This was the average latency over 1 GiB of sequential reads done by
   this simple fio script:

     [global]
     size=1G
     filename=/root/dax/data
     fallocate=none
     [io]
     rw=read
     ioengine=mmap

3) The fact that we had to check for both DAX exceptional entries and
   for page cache pages in the radix tree made the DAX code more
   complex.

Solve these issues by following the lead of the DAX PMD code and using a
common 4k zero page instead.  As with the PMD code we will now insert a
DAX exceptional entry into the radix tree instead of a struct page
pointer which allows us to remove all the special casing in the DAX
code.

Note that we do still pretty aggressively check for regular pages in the
DAX radix tree, especially where we take action based on the bits set in
the page.  If we ever find a regular page in our radix tree now that
most likely means that someone besides DAX is inserting pages (which has
happened lots of times in the past), and we want to find that out early
and fail loudly.

This solution also removes the extra memory consumption.  Here is that
same /proc/[pid]/smaps after 1GiB of reading from a hole with the new
code:

	7f2054a74000-7f2094a74000 rw-s 00000000 103:00 12   /root/dax/data
	Size:            1048576 kB
	Rss:                   0 kB
	Pss:                   0 kB
	Shared_Clean:          0 kB
	Shared_Dirty:          0 kB
	Private_Clean:         0 kB
	Private_Dirty:         0 kB
	Referenced:            0 kB
	Anonymous:             0 kB
	LazyFree:              0 kB
	AnonHugePages:         0 kB
	ShmemPmdMapped:        0 kB
	Shared_Hugetlb:        0 kB
	Private_Hugetlb:       0 kB
	Swap:                  0 kB
	SwapPss:               0 kB
	KernelPageSize:        4 kB
	MMUPageSize:           4 kB
	Locked:                0 kB

Overall system memory consumption is similarly improved.

Another major change is that we remove dax_pfn_mkwrite() from our fault
flow, and instead rely on the page fault itself to make the PTE dirty
and writeable.  The following description from the patch adding the
vm_insert_mixed_mkwrite() call explains this a little more:

   "To be able to use the common 4k zero page in DAX we need to have our
    PTE fault path look more like our PMD fault path where a PTE entry
    can be marked as dirty and writeable as it is first inserted rather
    than waiting for a follow-up dax_pfn_mkwrite() =>
    finish_mkwrite_fault() call.

    Right now we can rely on having a dax_pfn_mkwrite() call because we
    can distinguish between these two cases in do_wp_page():

            case 1: 4k zero page => writable DAX storage
            case 2: read-only DAX storage => writeable DAX storage

    This distinction is made by via vm_normal_page(). vm_normal_page()
    returns false for the common 4k zero page, though, just as it does
    for DAX ptes. Instead of special casing the DAX + 4k zero page case
    we will simplify our DAX PTE page fault sequence so that it matches
    our DAX PMD sequence, and get rid of the dax_pfn_mkwrite() helper.
    We will instead use dax_iomap_fault() to handle write-protection
    faults.

    This means that insert_pfn() needs to follow the lead of
    insert_pfn_pmd() and allow us to pass in a 'mkwrite' flag. If
    'mkwrite' is set insert_pfn() will do the work that was previously
    done by wp_page_reuse() as part of the dax_pfn_mkwrite() call path"

Link: http://lkml.kernel.org/r/20170724170616.25810-4-ross.zwisler@linux.intel.comSigned-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

dax_load_hole() will soon need to call dax_insert_mapping_entry(), so it
needs to be moved lower in dax.c so the definition exists.

dax_wake_mapping_entry_waiter() will soon be removed from dax.h and be
made static to dax.c, so we need to move its definition above all its
callers.

Link: http://lkml.kernel.org/r/20170724170616.25810-3-ross.zwisler@linux.intel.comSigned-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace all mmu_notifier_invalidate_page() calls by *_invalidate_range()
and make sure it is bracketed by calls to *_invalidate_range_start()/end().

Note that because we can not presume the pmd value or pte value we have
to assume the worst and unconditionaly report an invalidation as
happening.
Signed-off-by: NJérôme Glisse <jglisse@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Bernhard Held <berny156@gmx.de>
Cc: Adam Borowski <kilobyte@angband.pl>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Wanpeng Li <kernellwp@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: axie <axie@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In DAX there are two separate places where the 2MiB range of a PMD is
defined.

The first is in the page tables, where a PMD mapping inserted for a
given address spans from (vmf->address & PMD_MASK) to ((vmf->address &
PMD_MASK) + PMD_SIZE - 1).  That is, from the 2MiB boundary below the
address to the 2MiB boundary above the address.

So, for example, a fault at address 3MiB (0x30 0000) falls within the
PMD that ranges from 2MiB (0x20 0000) to 4MiB (0x40 0000).

The second PMD range is in the mapping->page_tree, where a given file
offset is covered by a radix tree entry that spans from one 2MiB aligned
file offset to another 2MiB aligned file offset.

So, for example, the file offset for 3MiB (pgoff 768) falls within the
PMD range for the order 9 radix tree entry that ranges from 2MiB (pgoff
512) to 4MiB (pgoff 1024).

This system works so long as the addresses and file offsets for a given
mapping both have the same offsets relative to the start of each PMD.

Consider the case where the starting address for a given file isn't 2MiB
aligned - say our faulting address is 3 MiB (0x30 0000), but that
corresponds to the beginning of our file (pgoff 0).  Now all the PMDs in
the mapping are misaligned so that the 2MiB range defined in the page
tables never matches up with the 2MiB range defined in the radix tree.

The current code notices this case for DAX faults to storage with the
following test in dax_pmd_insert_mapping():

	if (pfn_t_to_pfn(pfn) & PG_PMD_COLOUR)
		goto unlock_fallback;

This test makes sure that the pfn we get from the driver is 2MiB
aligned, and relies on the assumption that the 2MiB alignment of the pfn
we get back from the driver matches the 2MiB alignment of the faulting
address.

However, faults to holes were not checked and we could hit the problem
described above.

This was reported in response to the NVML nvml/src/test/pmempool_sync
TEST5:

	$ cd nvml/src/test/pmempool_sync
	$ make TEST5

You can grab NVML here:

	https://github.com/pmem/nvml/

The dmesg warning you see when you hit this error is:

  WARNING: CPU: 13 PID: 2900 at fs/dax.c:641 dax_insert_mapping_entry+0x2df/0x310

Where we notice in dax_insert_mapping_entry() that the radix tree entry
we are about to replace doesn't match the locked entry that we had
previously inserted into the tree.  This happens because the initial
insertion was done in grab_mapping_entry() using a pgoff calculated from
the faulting address (vmf->address), and the replacement in
dax_pmd_load_hole() => dax_insert_mapping_entry() is done using
vmf->pgoff.

In our failure case those two page offsets (one calculated from
vmf->address, one using vmf->pgoff) point to different order 9 radix
tree entries.

This failure case can result in a deadlock because the radix tree unlock
also happens on the pgoff calculated from vmf->address.  This means that
the locked radix tree entry that we swapped in to the tree in
dax_insert_mapping_entry() using vmf->pgoff is never unlocked, so all
future faults to that 2MiB range will block forever.

Fix this by validating that the faulting address's PMD offset matches
the PMD offset from the start of the file.  This check is done at the
very beginning of the fault and covers faults that would have mapped to
storage as well as faults to holes.  I left the COLOUR check in
dax_pmd_insert_mapping() in place in case we ever hit the insanity
condition where the alignment of the pfn we get from the driver doesn't
match the alignment of the userspace address.

Link: http://lkml.kernel.org/r/20170822222436.18926-1-ross.zwisler@linux.intel.comSigned-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Reported-by: N"Slusarz, Marcin" <marcin.slusarz@intel.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Track the following reclaim counters for every memory cgroup: PGREFILL,
PGSCAN, PGSTEAL, PGACTIVATE, PGDEACTIVATE, PGLAZYFREE and PGLAZYFREED.

These values are exposed using the memory.stats interface of cgroup v2.

The meaning of each value is the same as for global counters, available
using /proc/vmstat.

Also, for consistency, rename mem_cgroup_count_vm_event() to
count_memcg_event_mm().

Link: http://lkml.kernel.org/r/1494530183-30808-1-git-send-email-guro@fb.comSigned-off-by: NRoman Gushchin <guro@fb.com>
Suggested-by: NJohannes Weiner <hannes@cmpxchg.org>
Acked-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NVladimir Davydov <vdavydov.dev@gmail.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Jan Kara's description for this patch is much better than mine, so I'm
quoting it verbatim here:

DAX currently doesn't set errors in the mapping when cache flushing
fails in dax_writeback_mapping_range(). Since this function can get
called only from fsync(2) or sync(2), this is actually as good as it can
currently get since we correctly propagate the error up from
dax_writeback_mapping_range() to filemap_fdatawrite()

However, in the future better writeback error handling will enable us to
properly report these errors on fsync(2) even if there are multiple file
descriptors open against the file or if sync(2) gets called before
fsync(2). So convert DAX to using standard error reporting through the
mapping.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-and-tested-by: NRoss Zwisler <ross.zwisler@linux.intel.com>

Now that all callers of the pmem api have been converted to dax helpers that
call back to the pmem driver, we can remove include/linux/pmem.h and
asm/pmem.h.

Cc: <x86@kernel.org>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Oliver O'Halloran <oohall@gmail.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

dax_writeback_mapping_range() fails to update iteration index when
searching radix tree for entries needing cache flushing.  Thus each
pagevec worth of entries is searched starting from the start which is
inefficient and prone to livelocks.  Update index properly.

Link: http://lkml.kernel.org/r/20170619124531.21491-1-jack@suse.cz
Fixes: 9973c98e ("dax: add support for fsync/sync")
Signed-off-by: NJan Kara <jack@suse.cz>
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rename:

	wait_queue_t		=>	wait_queue_entry_t

'wait_queue_t' was always a slight misnomer: its name implies that it's a "queue",
but in reality it's a queue *entry*. The 'real' queue is the wait queue head,
which had to carry the name.

Start sorting this out by renaming it to 'wait_queue_entry_t'.

This also allows the real structure name 'struct __wait_queue' to
lose its double underscore and become 'struct wait_queue_entry',
which is the more canonical nomenclature for such data types.

Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

The clear_pmem() helper simply combines a memset() plus a cache flush.
Now that the flush routine is optionally provided by the dax device
driver we can avoid unnecessary cache management on dax devices fronting
volatile memory.

With clear_pmem() gone we can follow on with a patch to make pmem cache
management completely defined within the pmem driver.

Cc: <x86@kernel.org>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Filesystem-DAX flushes caches whenever it writes to the address returned
through dax_direct_access() and when writing back dirty radix entries.
That flushing is only required in the pmem case, so the dax_flush()
helper skips cache management work when the underlying driver does not
specify a flush method.

We still do all the dirty tracking since the radix entry will already be
there for locking purposes. However, the work to clean the entry will be
a nop for some dax drivers.

Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Now that all possible providers of the dax_operations copy_from_iter
method are implemented, switch filesytem-dax to call the driver rather
than copy_to_iter_pmem.
Reviewed-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

We currently have two related PMD vs PTE races in the DAX code.  These
can both be easily triggered by having two threads reading and writing
simultaneously to the same private mapping, with the key being that
private mapping reads can be handled with PMDs but private mapping
writes are always handled with PTEs so that we can COW.

Here is the first race:

  CPU 0					CPU 1

  (private mapping write)
  __handle_mm_fault()
    create_huge_pmd() - FALLBACK
    handle_pte_fault()
      passes check for pmd_devmap()

					(private mapping read)
					__handle_mm_fault()
					  create_huge_pmd()
					    dax_iomap_pmd_fault() inserts PMD

      dax_iomap_pte_fault() does a PTE fault, but we already have a DAX PMD
      			  installed in our page tables at this spot.

Here's the second race:

  CPU 0					CPU 1

  (private mapping read)
  __handle_mm_fault()
    passes check for pmd_none()
    create_huge_pmd()
      dax_iomap_pmd_fault() inserts PMD

  (private mapping write)
  __handle_mm_fault()
    create_huge_pmd() - FALLBACK
					(private mapping read)
					__handle_mm_fault()
					  passes check for pmd_none()
					  create_huge_pmd()

    handle_pte_fault()
      dax_iomap_pte_fault() inserts PTE
					    dax_iomap_pmd_fault() inserts PMD,
					       but we already have a PTE at
					       this spot.

The core of the issue is that while there is isolation between faults to
the same range in the DAX fault handlers via our DAX entry locking,
there is no isolation between faults in the code in mm/memory.c.  This
means for instance that this code in __handle_mm_fault() can run:

	if (pmd_none(*vmf.pmd) && transparent_hugepage_enabled(vma)) {
		ret = create_huge_pmd(&vmf);

But by the time we actually get to run the fault handler called by
create_huge_pmd(), the PMD is no longer pmd_none() because a racing PTE
fault has installed a normal PMD here as a parent.  This is the cause of
the 2nd race.  The first race is similar - there is the following check
in handle_pte_fault():

	} else {
		/* See comment in pte_alloc_one_map() */
		if (pmd_devmap(*vmf->pmd) || pmd_trans_unstable(vmf->pmd))
			return 0;

So if a pmd_devmap() PMD (a DAX PMD) has been installed at vmf->pmd, we
will bail and retry the fault.  This is correct, but there is nothing
preventing the PMD from being installed after this check but before we
actually get to the DAX PTE fault handlers.

In my testing these races result in the following types of errors:

  BUG: Bad rss-counter state mm:ffff8800a817d280 idx:1 val:1
  BUG: non-zero nr_ptes on freeing mm: 15

Fix this issue by having the DAX fault handlers verify that it is safe
to continue their fault after they have taken an entry lock to block
other racing faults.

[ross.zwisler@linux.intel.com: improve fix for colliding PMD & PTE entries]
  Link: http://lkml.kernel.org/r/20170526195932.32178-1-ross.zwisler@linux.intel.com
Link: http://lkml.kernel.org/r/20170522215749.23516-2-ross.zwisler@linux.intel.comSigned-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Reported-by: NPawel Lebioda <pawel.lebioda@intel.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Pawel Lebioda <pawel.lebioda@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Xiong Zhou <xzhou@redhat.com>
Cc: Eryu Guan <eguan@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is based on a patch from Jan Kara that fixed the equivalent race in
the DAX PTE fault path.

Currently DAX PMD read fault can race with write(2) in the following
way:

CPU1 - write(2)                 CPU2 - read fault
                                dax_iomap_pmd_fault()
                                  ->iomap_begin() - sees hole

dax_iomap_rw()
  iomap_apply()
    ->iomap_begin - allocates blocks
    dax_iomap_actor()
      invalidate_inode_pages2_range()
        - there's nothing to invalidate

                                  grab_mapping_entry()
				  - we add huge zero page to the radix tree
				    and map it to page tables

The result is that hole page is mapped into page tables (and thus zeros
are seen in mmap) while file has data written in that place.

Fix the problem by locking exception entry before mapping blocks for the
fault.  That way we are sure invalidate_inode_pages2_range() call for
racing write will either block on entry lock waiting for the fault to
finish (and unmap stale page tables after that) or read fault will see
already allocated blocks by write(2).

Fixes: 9f141d6e ("dax: Call ->iomap_begin without entry lock during dax fault")
Link: http://lkml.kernel.org/r/20170510172700.18991-1-ross.zwisler@linux.intel.comSigned-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: NJan Kara <jack@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently DAX read fault can race with write(2) in the following way:

CPU1 - write(2)			CPU2 - read fault
				dax_iomap_pte_fault()
				  ->iomap_begin() - sees hole
dax_iomap_rw()
  iomap_apply()
    ->iomap_begin - allocates blocks
    dax_iomap_actor()
      invalidate_inode_pages2_range()
        - there's nothing to invalidate
				  grab_mapping_entry()
				  - we add zero page in the radix tree
				    and map it to page tables

The result is that hole page is mapped into page tables (and thus zeros
are seen in mmap) while file has data written in that place.

Fix the problem by locking exception entry before mapping blocks for the
fault.  That way we are sure invalidate_inode_pages2_range() call for
racing write will either block on entry lock waiting for the fault to
finish (and unmap stale page tables after that) or read fault will see
already allocated blocks by write(2).

Fixes: 9f141d6e
Link: http://lkml.kernel.org/r/20170510085419.27601-5-jack@suse.czSigned-off-by: NJan Kara <jack@suse.cz>
Reviewed-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>