We must fully update the control segment before marking it as valid,
so that hardware doesn't start executing it before we're ready.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>

[ Move VLAN control bit setting to before wmb().  - Roland ]
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch allows IBoE traffic to be encapsulated in 802.1Q tagged
VLAN frames.  The VLAN tag is encoded in the GID and derived from it
by a simple computation.

The netdev notifier callback is modified to catch VLAN device
addition/removal and the port's GID table is updated to reflect the
change, so that for each netdevice there is an entry in the GID table.
When the port's GID table is exhausted, GID entries will not be added.
Only children of the main interfaces can add to the GID table; if a
VLAN interface is added on another VLAN interface (e.g. "vconfig add
eth2.6 8"), then that interfaces will not add an entry to the GID
table.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add 802.1q VLAN support to IBoE. The VLAN tag is encoded within the
GID derived from a link local address in the following way:

    GID[11] GID[12] contain the VLAN ID when the GID contains a VLAN.

The 3 bits user priority field of the packets are identical to the 3
bits of the SL.

In case of rdma_cm apps, the TOS field is used to generate the SL
field by doing a shift right of 5 bits effectively taking to 3 MS bits
of the TOS field.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for IBoE to mlx4_ib.  The bulk of the code is handling the
new address vector fields; mlx4 needs the MAC address of a remote node
to include it in a WQE (for datagrams) or in the QP context (for
connected QPs).  Address resolution is done by assuming all unicast
GIDs are either link-local IPv6 addresses.

Multicast group attach/detach needs to update the NIC's multicast
filters; but since attaching a QP to a multicast group can be done
before the QP is bound to a port, for IBoE we need to keep track of
all multicast groups that a QP is attached too before it transitions
from INIT to RTR (since it does not have a port in the INIT state).
Signed-off-by: NEli Cohen <eli@mellanox.co.il>

[ Many things cleaned up and otherwise monkeyed with; hope I didn't
  introduce too many bugs.  - Roland ]
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for packing IBoE packet headers.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>

[ Clean up and fix ib_ud_header_init() a bit.  - Roland ]
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for masked atomic operations (masked compare and swap,
masked fetch and add).
Signed-off-by: NVladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

ib_ud_header_init() first clears header and then fills up the various
fields.  Later on, it tests header->immediate_present, which it has
already cleared, so the condition is always false.  Fix this by adding
an immediate_present parameter and setting header->immediate_present
as is done with grh_present.  Also remove unused calculation of
header_len.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

struct ib_qp  already holds a pointer to the ib device. No need to dive to the
hw device object to retrieve it.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In mlx4_ib_post_recv(), we should check the queue for overflow using
recv_cq instead of send_cq (current code looks like a copy-and-paste
mistake).
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Current code has a limitation: an LSO header is not allowed to cross a
64 byte boundary.  This patch removes this limitation by setting the
WQE RR for large headers thus allowing LSO headers of any size.  The
extra buffer reserved for MLX4_IB_QP_LSO QPs has been doubled, from 64
to 128 bytes, assuming this is reasonable upper limit for header
length.  Also, this patch will cause IB_DEVICE_UD_TSO to be set only
for HCA FW versions that set MLX4_DEV_CAP_FLAG_BLH; e.g. FW version
2.6.000 and higher.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There is no such flag DE - the field is reserved and should be zero.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

mlx4_ib_lock_cqs()/mlx4_ib_unlock_cqs() are helper functions that
lock/unlock both CQs attached to a QP in the proper order to avoid
AB-BA deadlocks.  Annotate this so sparse can understand what's going
on (and warn us if we misuse these functions).
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The ConnectX Programmer's Reference Manual states that the "SO" bit
must be set when posting Fast Register and Local Invalidate send work
requests.  When this bit is set, the work request will be executed
only after all previous work requests on the send queue have been
executed.  (If the bit is not set, Fast Register and Local Invalidate
WQEs may begin execution too early, which violates the defined
semantics for these operations)

This fixes the issue with NFS/RDMA reported in
<http://lists.openfabrics.org/pipermail/general/2009-April/059253.html>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Cc: <stable@kernel.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The low-level mlx4 driver modified the page-list addresses for fast
register work requests post send to big-endian, and set a "present"
bit.  This caused problems later when the consumer attempted to unmap
the pages using the page-list (using the list addresses which were
assumed to be still in CPU-endian order).  Fix the mlx4 driver to
allocate two buffers and use a private buffer for the hardware-format
bus addresses.

This patch fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1571>,
an NFS/RDMA server crash.  The cause of the crash was found by Vu Pham
of Mellanox.  The fix is along the lines suggested by Steve Wise in
comment #21 in bug 1571.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The base versions handle constant folding just fine, use them
directly.  The replacements are OK in the include/ files as they are
not exported to userspace so we don't need the __ prefixed versions.

This patch does not affect code generation at all.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The current work request posting code writes the LSO segment before
writing any data segments.  This leaves a window where the LSO segment
overwrites the stamping in one cacheline that the HCA prefetches
before the rest of the cacheline is filled with the correct data
segments.  When the HCA processes this work request, a local
protection error may result.

Fix this by saving the LSO header size field off and writing it only
after all data segments are written.  This fix is a cleaned-up version
of a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1383>.
Reported-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

To allow allocating an aligned range of consecutive QP numbers, add an
interface to reserve an aligned range of QP numbers and have the QP
allocation function always take a QP number.

This will be used for RSS support in the mlx4_en Ethernet driver and
also potentially by IPoIB RSS support.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Set RLKEY bit in the HW context for kernel QPs so that kernel QPs can
use the reserved L_Key for memory reference.
Signed-off-by: NVladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Byte swap the addresses in the page list for fast register work requests
to big endian to match what the HCA expectx.  Also, the addresses must
have the "present" bit set so that the HCA knows it can access them.
Otherwise the HCA will fault the first time it accesses the memory
region.
Signed-off-by: NVladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Current code limits the max message size to 2K for UD QPs, while MTU
might be as big as 4K.  This patch sets the maximum message size to
4K, which is needed for UD to work correctly on fabrics with a 4K MTU.
Signed-off-by: NAlex Naslednikov <xalex@mellanox.co.il>
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Update existing Mellanox copyright lines to 2008, and add such lines
to files where they are missing.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for the following operations to mlx4 when device firmware
supports them:

 - Send with invalidate and local invalidate send queue work requests;
 - Allocate/free fast register MRs;
 - Allocate/free fast register MR page lists;
 - Fast register MR send queue work requests;
 - Local DMA L_Key.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Make the struct name consistent with other WQE segment struct types
defined in <linux/mlx4/qp.h>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Current code uses kmalloc() and then just does a bitwise OR operation on
qp->flags in create_qp_common(), which means that qp->flags may
potentially have some unintended bits set.  This patch uses kzalloc()
and avoids further explicit clearing of structure members, which also
shrinks the code:

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-65 (-65)
function                                     old     new   delta
create_qp_common                            2024    1959     -65
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for handling the IB_QP_CREATE_MULTICAST_BLOCK_LOOPBACK
flag by using the per-multicast group loopback blocking feature of
mlx4 hardware.
Signed-off-by: NRon Livne <ronli@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Commit 65adfa91 ("IB/mlx4: Fix RESET to RESET and RESET to ERROR
transitions") added some extra code to handle a QP state transition
from RESET to ERROR.  However, the latest 1.2.1 version of the IB spec
has clarified that this transition is actually not allowed, so we can
remove this extra code again.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ConnectX returns the max message size it supports through the
QUERY_DEV_CAP firmware command.  When modifying a QP to RTR, the max
message size for the QP must be specified.  This value must not exceed
the value declared through QUERY_DEV_CAP.  The current code ignores
the max allowed size and unconditionally sets the value to 2^31.  This
patch sets all QPs to the max value allowed as returned from firmware.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The idea is that for QPs with fixed size work requests (eg selective
signaling QPs), before stamping the WQE, we read the value of the DS
field, which gives the effective size of the descriptor as used in the
previous post.  Then we stamp only that area, since the rest of the
descriptor is already stamped.

When initializing the send queue buffer, make sure the DS field is
initialized to the max descriptor size so that the subsequent stamping
will be done on the entire descriptor area.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When creating a kernel QP where the consumer asked for a send queue
with lots of scatter/gater entries, set_kernel_sq_size() incorrectly
returned an error if the send queue stride is larger than the
hardware's maximum send work request descriptor size.  This is not a
problem; the only issue is to make sure that the actual descriptors
used do not overflow the maximum descriptor size, so check this instead.

Clamp the returned max_send_sge value to be no bigger than what
query_device returns for the max_sge to avoid confusing hapless users,
even if the hardware is capable of handling a few more s/g entries.

This bug caused NFS/RDMA mounts to fail when the server adapter used
the mlx4 driver.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

    drivers/infiniband/hw/mlx4/qp.c: In function 'mlx4_ib_post_send':
    drivers/infiniband/hw/mlx4/qp.c:1460: warning: 'seglen' may be used uninitialized in this function

This is the dopey gcc-doesn't-know-that-foo(&var)-writes-to-var problem.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a new parameter, dmasync, to the ib_umem_get() prototype.  Use dmasync = 1
when mapping user-allocated CQs with ib_umem_get().
Signed-off-by: NArthur Kepner <akepner@sgi.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In addition to mlx4_ib, there will be ethernet and FC consumers of
mlx4_core, so move the code for managing kernel doorbells into the
core module to avoid having to duplicate this multiple times.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

If the QP was moved to another state (such as SQE) by the hardware,
then after this change the user won't have to set the IBV_QP_CUR_STATE
mask in order to execute modify QP in order to recover from this state.
Signed-off-by: NDotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a new IB_WR_SEND_WITH_INV send opcode that can be used to mark a
"send with invalidate" work request as defined in the iWARP verbs and
the InfiniBand base memory management extensions.  Also put "imm_data"
and a new "invalidate_rkey" member in a new "ex" union in struct
ib_send_wr. The invalidate_rkey member can be used to pass in an
R_Key/STag to be invalidated.  Add this new union to struct
ib_uverbs_send_wr.  Add code to copy the invalidate_rkey field in
ib_uverbs_post_send().

Fix up low-level drivers to deal with the change to struct ib_send_wr,
and just remove the imm_data initialization from net/sunrpc/xprtrdma/,
since that code never does any send with immediate operations.

Also, move the existing IB_DEVICE_SEND_W_INV flag to a new bit, since
the iWARP drivers currently in the tree set the bit.  The amso1100
driver at least will silently fail to honor the IB_SEND_INVALIDATE bit
if passed in as part of userspace send requests (since it does not
implement kernel bypass work request queueing).  Remove the flag from
all existing drivers that set it until we know which ones are OK.

The values chosen for the new flag is not consecutive to avoid clashing
with flags defined in the XRC patches, which are not merged yet but
which are already in use and are likely to be merged soon.

This resurrects a patch sent long ago by Mikkel Hagen <mhagen@iol.unh.edu>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Rather than have build_mlx_header() return a negative value on failure
and the length of the segments it builds on success, add a pointer
parameter to return the length and return 0 on success.  This matches
the calling convention used for build_lso_seg() and generates slightly
smaller code -- eg, on 64-bit x86:

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-22 (-22)
function                                     old     new   delta
mlx4_ib_post_send                           2023    2001     -22
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add TSO support to the mlx4_ib driver.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a create_flags member to struct ib_qp_init_attr that will allow a
kernel verbs consumer to create a pass special flags when creating a QP.
Add a flag value for telling low-level drivers that a QP will be used
for IPoIB UD LSO.  The create_flags member will also be useful for XRC
and ehca low-latency QP support.

Since no create_flags handling is implemented yet, add code to all
low-level drivers to return -EINVAL if create_flags is non-zero.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ConnectX devices support checksum generation and verification of TCP
and UDP packets for UD IPoIB messages.  This patch checks if the HCA
supports this and sets the IB_DEVICE_UD_IP_CSUM capability flag if it
does.  It implements support for handling the IB_SEND_IP_CSUM send
flag and setting the csum_ok field in receive work completions.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NAli Ayub <ali@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>