- 29 1月, 2013 1 次提交
-
-
由 David J. Choi 提交于
Summary of changes: .Newly added phys -KSZ8081/KSZ8091, which has some phy ids. -KSZ8061 -KSZ9031, which is Gigabit phy. -KSZ886X, which has a switch function. -KSZ8031, which has a same phy ids with KSZ8021. Signed-off-by: NDavid J. Choi <david.choi@micrel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 11月, 2012 1 次提交
-
-
this will allow to detect the link between the switch and the soc Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: netdev@vger.kernel.org Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 9月, 2012 2 次提交
-
-
由 Marek Vasut 提交于
There is no such part as KS8001, KS8041 or KS8051. There are only KSZ8001, KSZ8041 and KSZ8051. Rename these parts as such to match the Micrel naming. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: David J. Choi <david.choi@micrel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Marek Vasut 提交于
The KSZ8021 PHY was previously caught by KS8051, which is not correct. This PHY needs additional setup if it is strapped for address 0. In such case an reserved bit must be written in the 0x16, "Operation Mode Strap Override" register. According to the KS8051 datasheet, that bit means "PHY Address 0 in non-broadcast" and it indeed behaves as such on KSZ8021. The issue where the ethernet controller (Freescale FEC) did not communicate with network is fixed by writing this bit as 1. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: David J. Choi <david.choi@micrel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 09 7月, 2012 1 次提交
-
-
由 Christian Hohnstaedt 提交于
If registering of one of them fails, all already registered drivers of this module will be unregistered. Use the new register/unregister functions in all drivers registering more than one driver. amd.c, realtek.c: Simplify: directly return registration result. Tested with broadcom.c All others compile-tested. Signed-off-by: NChristian Hohnstaedt <chohnstaedt@innominate.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 6月, 2012 1 次提交
-
-
由 Jason Wang 提交于
On a freescale imx6q platform, a hardware phy chip KSZ9021 is recognized as a KS8001 chip by the current driver like this: eth0: Freescale FEC PHY driver [Micrel KS8001 or KS8721] KSZ9021 has phy_id 0x00221610, while KSZ8001 has phy_id 0x0022161a, the current phy_id_mask (0x00fffff0/0x00ffff10) can't distinguish them. So change phy_id_mask to resolve this problem. Although the micrel datasheet says that the 4 LSB of phyid2 register contains the chip revision number and the current driver is designed to follow this rule, in reality the chip implementation doesn't follow it. Cc: David J. Choi <david.choi@micrel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NHui Wang <jason77.wang@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 2月, 2011 1 次提交
-
-
由 Baruch Siach 提交于
Platform code can now set the MICREL_PHY_50MHZ_CLK bit of dev_flags in a fixup routine (registered with phy_register_fixup_for_uid()), to make the KZS8051RNL PHY work with 50MHz RMII reference clock. Cc: David J. Choi <david.choi@micrel.com> Signed-off-by: NBaruch Siach <baruch@tkos.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 10月, 2010 1 次提交
-
-
由 Uwe Kleine-König 提交于
MODULE_DEVICE_TABLE only expands to something if it's compiled for a module. So when building-in support for the phys, the mdio_device_id tables are unused. Marking them with __maybe_unused fixes the following warnings: drivers/net/phy/bcm63xx.c:134: warning: 'bcm63xx_tbl' defined but not used drivers/net/phy/broadcom.c:933: warning: 'broadcom_tbl' defined but not used drivers/net/phy/cicada.c:162: warning: 'cicada_tbl' defined but not used drivers/net/phy/davicom.c:222: warning: 'davicom_tbl' defined but not used drivers/net/phy/et1011c.c:114: warning: 'et1011c_tbl' defined but not used drivers/net/phy/icplus.c:137: warning: 'icplus_tbl' defined but not used drivers/net/phy/lxt.c:226: warning: 'lxt_tbl' defined but not used drivers/net/phy/marvell.c:724: warning: 'marvell_tbl' defined but not used drivers/net/phy/micrel.c:234: warning: 'micrel_tbl' defined but not used drivers/net/phy/national.c:154: warning: 'ns_tbl' defined but not used drivers/net/phy/qsemi.c:141: warning: 'qs6612_tbl' defined but not used drivers/net/phy/realtek.c:82: warning: 'realtek_tbl' defined but not used drivers/net/phy/smsc.c:257: warning: 'smsc_tbl' defined but not used drivers/net/phy/ste10Xp.c:135: warning: 'ste10Xp_tbl' defined but not used drivers/net/phy/vitesse.c:195: warning: 'vitesse_tbl' defined but not used Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 6月, 2010 1 次提交
-
-
由 Choi, David 提交于
Hello all: This patch fixes what Ben mentioned, namely duplicated ids. From: David J. Choi <david.choi@micrel.com> Body of the explanation: This patch has changes as followings; -support the interrupt from phy devices from Micrel Inc. -support more phy devices, ks8737, ks8721, ks8041, ks8051 from Micrel. -remove vsc8201 because this device was used only internal test at Micrel. Signed-off-by: NDavid J. Choi <david.choi@micrel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 5月, 2010 1 次提交
-
-
由 David S. Miller 提交于
Missing name string in ks8001_driver, so we crash on register. Reported-by: NIngo Molnar <mingo@elte.hu> Tested-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 5月, 2010 2 次提交
-
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David J. Choi 提交于
This is the first version of phy driver from Micrel Inc. Signed-off-by: NDavid J. Choi <david.choi@micrel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-