When a driver is set up without the jack detection explicitly (either
by passing a model option or via a specific fixup), the pin powermap
of IDT/STAC codecs is set up wrongly, resulting in the silence
output.  It's because of a logic failure in stac_init_power_map().
It tries to avoid creating a callback for the pins that have other
auto-hp and auto-mic callbacks, but the check is done in a wrong way
at a wrong time.  The stac_init_power_map() should be called after
creating other jack detection ctls, and the jack callback should be
created only for jack-detectable widgets.

This patch fixes the check in stac_init_power_map() and its callee
at the right place, after snd_hda_gen_build_controls().
Reported-by: NAdam Richter <adam_richter2004@yahoo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALC1150 codec seems to need the COEF- and PLL-setups just like its
compatible ALC882 codec.  Some machines (e.g. SunMicro X10SAT) show
the problem like too low output volumes unless the COEF setup is
applied.
Reported-and-tested-by: NDana Goyette <danagoyette@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Acer Aspire 3830TG with CX20588 codec has a digital built-in mic that
has the same problem like many others, the inverted signal in stereo.
Apply the same fixup to this machine, too.

Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Acer Aspire V5 doesn't set up the pins correctly at the cold boot
while the pins are corrected after the warm reboot.  This patch gives
the proper pin configs statically in the driver as a workaround.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81561Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Valleyview and Cherryview have the same behavior on display audio. So this patch
defines is_valleyview_plus() to include codecs for both Valleyview and its successor
Cherryview, and apply Valleyview fix-ups to Cherryview.
Signed-off-by: NLibin Yang <libin.yang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Both Haswell and Broadwell need set depop_delay to 0. So apply this
setting to haswell plus.
Signed-off-by: NLibin Yang <libin.yang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

On some HP laptops, the mute led is controlled by codec gpio.

When some machine resume from s3/s4, the codec gpio data will be
cleared to 0 by BIOS:
Before suspend:
  IO[3]: enable=1, dir=1, wake=0, sticky=0, data=1, unsol=0
After resume:
  IO[3]: enable=1, dir=1, wake=0, sticky=0, data=0, unsol=0

To skip the AFG node to enter D3 can't fix this problem.

A workaround is to restore the gpio data when the system resume
back from s3/s4. It is safe even on the machines without this
problem.

BugLink: https://bugs.launchpad.net/bugs/1358116Tested-by: NFranz Hsieh <franz.hsieh@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALC269 & co have many vendor-specific setups with COEF verbs.
However, some verbs seem specific to some codec versions and they
result in the codec stalling.  Typically, such a case can be avoided
by checking the return value from reading a COEF.  If the return value
is -1, it implies that the COEF is invalid, thus it shouldn't be
written.

This patch adds the invalid COEF checks in appropriate places
accessing ALC269 and its variants.  The patch actually fixes the
resume problem on Acer AO725 laptop.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52181Tested-by: NFrancesco Muzio <muziofg@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Conexnat HD-audio driver has a workaround for cx5051 (aka CX20561)
chip to add fake mute controls to each amp (commit 3868137e).  This
implies the minimum-as-mute TLV bit in TLV for each corresponding
control.  Meanwhile we build the virtual master from these, but the
TLV bit is missing, even though the slaves have it.

This patch simply adds the missing TLV_DB_SCALE_MUTE bit for vmaster,
as already done in patch_sigmatel.c.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

CA0132 driver tries to reload the firmware at resume.  Usually this
works since the firmware loader core caches the firmware contents by
itself.  However, if the driver failed to load the firmwares
(e.g. missing files), reloading the firmware at resume goes through
the actual file loading code path, and triggers a kernel WARNING like:

 WARNING: CPU: 10 PID:11371 at drivers/base/firmware_class.c:1105 _request_firmware+0x9ab/0x9d0()

For avoiding this situation, this patch makes CA0132 skipping the f/w
loading at resume when it failed at probe time.
Reported-and-tested-by: NJanek Kozicki <cosurgi@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If nid 0x15 (Headphone Playback Switch) is in D3 and headphones are
plugged in when the laptop reboots, a pop noise is generated.
Prevent this by keeping nid 0x15 in D0 when headphones are plugged in.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=76611Signed-off-by: NGabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If the laptop is powered on with a jack plugged in, independently on what
is plugged, the jack is treated as a microphone jack.

Initialize the capture source so that by default jacks are treated as
headphones jacks. This will also prevent pop noises on boot in case
headphones are plugged in since setting/unsetting mic-in as input source
causes a pop noise.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=76611Signed-off-by: NGabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

CMI8888 codec chip has a boost amp (only) on the headphone pin, and
this confuses the generic parser, which tends to pick up the most
outside amp.  This results in the wrong volume setup, as the driver
complains like:
  hda_codec: Mismatching dB step for vmaster slave (-100!=1000)

For avoiding this problem, rule out the amp on NID 0x10 and create
"Headphone Amp" volume control manually instead.

Note that this patch still doesn't fix all problems yet.  The sound
output from the line out seems still too low.  It will be fixed in
another patch (hopefully).
Reported-and-tested-by: NVincent Lejeune <vljn@ovi.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ASUS Phoebus with CMI8888 HD-audio chip (PCI id 13f6:5011) doesn't
work with HD-audio driver as is because of some weird nature.  For
making DMA properly working, we need to disable MSI.  The position
report buffer doesn't work, thus we need to force reading LPIB
instead.  And yet, the codec CORB/RIRB communication gives errors
unless we disable the snooping (caching).

In this patch, all these workarounds are added as a quirk for the
device.  The HD-audio *codec* chip needs yet another workaround, but
it'll be provided in the succeeding patch.
Reported-and-tested-by: NVincent Lejeune <vljn@ovi.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It will be recording voice delay for resume back recording for Headset Mic.
This alc286 will quickly open Headset Mic, to prevent avoid recording files are missing.
The issue was fixed. This is follow ALC286 programing guide.

[fix build error, add static and renamed the function by tiwai]
Signed-off-by: NKailang Yang <kailang@realtek.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds codec ID (0x80862883) and module alias for Braswell
display codec.
Signed-off-by: NLibin Yang <libin.yang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add HD Audio Device PCI ID for the Intel Braswell platform.
It is an HDA Intel PCH controller.

AZX_DCAPS_ALIGN_BUFSIZE is not necessary for this controller.
Signed-off-by: NLibin Yang <libin.yang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The mic mute led on dell laptops is controlled by the wmi driver.
Followed this part being merged to the kernel, we add the mic mute led
hook in the hda driver.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ON the machine, two pin complex (0xb and 0xe) are both routed to
the same external right-side mic jack, this makes the jack can't work.

To fix this problem, set the 0xe to "not connected".

BugLink: https://bugs.launchpad.net/bugs/1350148Tested-by: NFranz Hsieh <franz.hsieh@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Dell XPS 15 (1028:05fe) gives the bad feedback noise from analog
loopback line even if the channels are muted.  The similar problem has
been seen on XPS 13, and it was fixed by simply disabling loopback.
The same fixup was confirmed to be applicable and fix the problem on
XPS 15, too.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80821Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a new quirk table to make sure that pin quirks have a higher
priority than quirks that apply to an entire vendor.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Previously, calling one quirk function first and another later
would make the latter one take priority, this is now changed
to make the former take priority.

By adding two special values for fixup_id we can also get rid of the
fixup_forced flag.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The Gigabyte BRIX BXBT-2707 is a mini-PC with Realtek ALC283 HDA,
exposing a single headset jack.

However, the default pin config information only suggests
that one pin is connected: a HP out jack (pin 0x21, default
config 0x04211010).

The microphone input is behind pin 0x19, which has default
config 0x411111f0 (i.e. unused), so it does not show up in
userspace, and no microphone input is possible via the headset.

Override the pin config so that the headset mic can be used.

[rearranged the fixup entry position by tiwai]
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This makes the mute LED work on a HP 15 touchsmart machine.

BugLink: https://bugs.launchpad.net/bugs/1334950Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Since devptr can be NULL due to asynchronous probe, all PM ops should
have NULL checks at the beginning.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

NID 0x10 seems corresponding to the bass speaker.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the initialization of Intel HDMI controller fails due to missing
i915 kernel symbols (e.g. HD-audio is built in while i915 is module),
the driver discontinues the probe.  However, since the probe was done
asynchronously, the driver object still remains, thus the relevant PM
ops are still called at suspend/resume. This results in the bad access
to the incomplete audio card object, eventually leads to Oops or stall
at PM.

This patch adds the missing checks of chip->init_failed flag at each
PM callback in order to fix the problem above.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79561
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

We got a regression report for 3.15.x kernels, and this turned out to
be triggered by the fix for stream assignment order.  On reporter's
machine with Intel controller (8086:1e20) + VIA VT1802 codec, the
first playback slot can't work with speaker outputs.

But the original commit was actually a fix for AMD controllers where
no proper GCAP value is returned, we shouldn't revert the whole
commit.  Instead, in this patch, a new flag is introduced to determine
the stream assignment order, and follow the old behavior for Intel
controllers.

Fixes: dcb32ecd ('ALSA: hda - Do not assign streams in reverse order')
Reported-and-tested-by: NSteven Newbury <steve@snewbury.org.uk>
Cc: <stable@vger.kernel.org> [v3.15+]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Now the led_power_filter() needs to handle 3 situations:
    - only mute_led_nid is set
    - only cap_mute_led_nid is set
    - both mute_led_ind and cap_mute_led_nid are set

BugLink: https://bugs.launchpad.net/bugs/1329580
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: Kailang Yang <kailang@realtek.com>
Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BugLink: https://bugs.launchpad.net/bugs/1329580
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: Kailang Yang <kailang@realtek.com>
Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Vendor ID 0x10de0070 is used by a yet-to-be-named GPU chip.
Signed-off-by: NAaron Plattner <aplattner@nvidia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The hda_tegra_disable_clocks() function is only used by the suspend and
resume code, so it needs to be included in the #ifdef CONFIG_PM_SLEEP
block to prevent the following warning:

  CC      sound/pci/hda/hda_tegra.o
sound/pci/hda/hda_tegra.c:238:13: warning: 'hda_tegra_disable_clocks' defined but not used [-Wunused-function]
 static void hda_tegra_disable_clocks(struct hda_tegra *data)
             ^
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BugLink: https://bugs.launchpad.net/bugs/1329580Signed-off-by: NHui Wang <hui.wang@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

print_nid_path has a possible buffer overflow if
struct nid_path.path values are > 256.

Avoid this and neaten the output to remove the leading ':'

Neaten debug_badness to always verify arguments.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For HSW/BDW display HD-A controller, hda_set_bclk() is defined to set BCLK
by programming the M/N values as per the core display clock (CDCLK) queried from
i915 display driver.

And the audio driver will also set BCLK in azx_first_init() since the display
driver can turn off the shared power in boot phase if only eDP is connected
and M/N values will be lost and must be reprogrammed.
Signed-off-by: NMengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

'status' is not used in the function. Remove it.
Signed-off-by: NSachin Kamat <sachin.kamat@samsung.com>
Tested-by: NDylan Reid <dgreid@chromium.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The "list" field has been omitted from struct azx, but its
initialization remained mistakenly in hda_tegra.c, which leads to a
compile error:
   sound/pci/hda/hda_tegra.c: In function 'hda_tegra_create':
   sound/pci/hda/hda_tegra.c:481:22: error: 'struct azx' has no member
named 'list'
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Fixes: 9a34af4a ('ALSA: hda - Move more PCI-controller-specific stuff from generic code')
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The recent commit [6194b99d: ALSA: hda - Kill the rest of snd_print*()
usages] changed the callback map_slaves(), but one call was forgotten
to be replaced due to the cast, which leads to kernel Oops due to
invalid function.  This patch replaces it with a proper function.

Fixes: 6194b99d ('ALSA: hda - Kill the rest of snd_print*() usages')
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The similar fixup as T440 is needed for supporting the dock on T540.
Reported-by: NJim Minter <jminter@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>