Use a helper for 2-wire and another for 3-wire.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since we now access it via the ath_hw declare the ath_hw pointer
at the header of some routines and se it. ath9k.h no longer needs to
access btcoex.h and to adjust for this move ath_btcoex_set_weight()
into btcoex.h and instead give main.c a helper for setting initial
values upon drv_start()
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is some bluetooth coexistance data which is driver
specific, stuff that into its own structure.

Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

DPRINTF() is used in hw specific related code, as such
ensure we don't rely on the private driver core ath_softc
struct when calling it. Drivers can then implement their
own DPRINTF() as they see fit.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a embarrassing bug which was introduced by:
"[PATCH] ar9170: implement frequency calibration for one-stage/openfw"

The phy_data variable initialization has to done outside the for-loop
scope. This is because the for-loop uses u32 phy_data variable more
like a 4-byte field. But in each run only a single byte is calculated.
Therefore phy_data content needs to stay the same for at least 3 more
iterations, before the complete set can be uploaded.
Reported-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes 2 issues in RFKILL:

* Calling wiphy_rfkill_stop_polling() in ath9k_stop
  would mean that the driver cannot report HW status
  when the radio is re-enabled. Move this to ath_detach().

* Calling ath_radio_{enable/disable} without checking the current
  state results in ath_radio_enable() being called repeatedly
  for every invocation of rfkill_poll(). This is not needed
  in any case since wiphy_rfkill_set_hw_state() would call
  ->stop() if the radio has been disabled.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds the usbid for TP-Link TL-WN821N v2.

Cc: stable@kernel.org
Reported-by: NFabian Lenz <lenz_fabian@yahoo.de>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Autosleep needs to be disabled for AR9287 chipsets also.
Since autosleep is not used for any of the currently supported
chipsets, disable it by default and can be enabled if needed
for any of the future chipsets.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: Fix bugs in programming registers during PA CAL"
removed a REG_READ of 0x7834. This resulted in incorrect
computation of the subsequent value to be written in RF2G6.

This patch fixes the regression by re-adding the REG_READ.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* This patch fixes a bug in calculating the scaled
  power for three chain chipsets.

* Also, a delay is needed after setting DAC low-power mode in
  TOP1 RF register (Top Level Register Bits).
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: Do an AHB reset before doing RTC reset"
fixed RTC reset issue for AR9280 2.0 chipsets and above.
The fix is valid for all AR9280 chipsets.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is needed to account for the number of chains in use,
not just the number of chains present.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9280 requires a full reset during channel change and HW reset.
Currently, a fast channel change is done. This patch fixes
this bug.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

NF value may be incorrect when we read it just after the chip
has gone through a full sleep mode. Reading incorrect NF values
affects RX throughput.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Setting bit 20 and 25 of 0x8344 can cause occasional rx data
corruption, clear them to fix this issue.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Waking up the chip after powering it down fails sometimes.
In this case the CPU is locked for 200ms. Reduce this
interval to 10ms to avoid excessive busy looping.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For chips requiring RTC reset, TSF has to be restored
after power on reset.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Disable L1 state ONLY when device is in D3 mode.
* Clear bit 22 of register 0x4004.
* Handle power on/off properly

Not setting the workarounds properly resulted in the
disappearance of the card in certain cases.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The default noise floor was never initialized for
AR9287.This patch helps in reporting the correct
RSSI for this version of chipset.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NUwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

When processing MIB interrupts, OFDM and CCK error
handling routines for low RSSI values have to be invoked
only when the channel mode is 11G/11B. Since HT channels
will also fall under the bands 2Ghz/5Ghz, check appropriately.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Oops, a stupid mistake in the original patch which adds coex 3-wire
support. Bluetooth priority gpio needs to be gpio 7.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This subsystem id will be used later to turn on the btcoex
support.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

apply the conformance test limits (CTL) stored in the eeprom upon
the values calculated for the tx power (ar->power_*).

This is based on the implementation in the vendor driver
(hal/hpmain.c, line 3700 ff.) with one difference:
If any ctl mode isn't found in the eeprom, we fall back to the "lower",
legacy modes (5GHT20,11A or 2GHT20,11G,11B). Otus only did 5GHT20->11A.

Currently CTL are applied for the FCC group only.
Signed-off-by: NJoerg Albert <jal2@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ar9170 driver needs the defines for conformance test limit groups
and cannot include regd_common.h
Signed-off-by: NJoerg Albert <jal2@gmx.de>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch ports some code from the vendor driver, which is
supposed to upload the right calibration values for the
chosen frequency.

In theory, this should give a better range and throughput
for all users with the open, or one-stage firmware.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CHANNEL_G has to be set for 2GHZ channels since
IS_CHAN_G() checks for this in channelFlags and not in
chanmode. To make things messier, ath9k_hw_process_ini()
checks for CHANNEL_G in chanmode and not in channelFlags.
The supreme, brain-searing fix is to set the
flag in both cases.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BAR frames have to be sent to mac80211 only if the
current channel is HT. Also, move the macro to
enum ath9k_rx_filter.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k ahb requests an IRQ and indicates 'ath9k' claimed it,
ath9k pci requests an IRQ and indicates 'ath'   claims it;
since 'ath' is another module sync both ahb and pci to claim
the irq using 'ath9k'.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We've cleaned up ath_init_device() and its children enough
to pass meaninful errors back from probe. When this fails
it means our device could not be initialized and a meaninful
error will have been passed.

Do the same for request_irq() and also synchronize the error
messages while at it.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The -ENOMEM was never being passed on failure.
While at it use dev_err() as ahb does upon failure.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds the initialisation of some PHY registers
from the modal_header[] values in the EEPROM
(see otus/hal/hpmain.c, line 333 ff.)
Signed-off-by: NJoerg Albert <jal2@gmx.de>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As generic hw timer interrupt handler is moved to tasklet,
we no more need to call spin_lock_irqsave().
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>