The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config TWL4030_CORE
drivers/mfd/Kconfig:    bool "TI TWL4030/TWL5030/TWL6030/TPS659x0 Support"

...meaning that it currently is not being built as a module by anyone.

Lets remove what modular code that we can, so that when reading the
driver there is less doubt that it is builtin-only.  Note that we can't
remove the twl_remove() itself ; it is still used by the probe unwind
routine.  So we leave it linked into the .remove as well, even though
it will most likely never be called via that path from an unbind.

Since module_i2c_driver() uses the same init level priority as
builtin_i2c_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config MFD_SUN6I_PRCM
drivers/mfd/Kconfig:    bool "Allwinner A31 PRCM controller"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config MFD_SMSC
drivers/mfd/Kconfig:       bool "SMSC ECE1099 series chips"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.

We replace module.h with init.h and delete an unused moduleparam.h
include.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config MFD_INTEL_MSIC
drivers/mfd/Kconfig:    bool "Intel MSIC

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple instances of module references, so that
when reading the driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config MFD_AS3722
drivers/mfd/Kconfig:    bool "ams AS3722 Power Management IC"

...meaning that it currently is not being built as a module by anyone.

In response to an earlier patch set suggesting removal of the unused
modular code, Laxman suggested that this driver be instead moved to
tristate.

We do that here, and confirm it can build and modpost as a tristate.
However there remains to be runtime testing in order to ensure this
change is 100% functional for "=m".

Cc: Florian Lobmaier <florian.lobmaier@ams.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Kconfig currently controlling compilation of this code is:

drivers/mfd/Kconfig:config MFD_ALTERA_A10SR
drivers/mfd/Kconfig:    bool "Altera Arria10 DevKit System Resource chip"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since builtin_driver() uses the same init level priority as
module_spi_driver() the init ordering remains unchanged with
this commit. [Note that there is no builtin_spi_driver macro,
so we open-code what it would be via builtin_driver().]

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add tps65217 power buttor subdevice with assigned IRQ resources.
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add support for handling IRQs: power button, AC and USB power state
changes. Mask and interrupt bits are shared within one register, which
prevents us to use regmap_irq implementation. New irq_domain is created in
order to add interrupt handling for each tps65217's subsystem. IRQ
resources have been added for charger subsystem to be able to notify about
AC and USB state changes.
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

These structures are only used to copy into other structures, so declare
them as const.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };

@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;

@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NAndrew Jeffery <andrew@aj.id.au>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NJoel Stanley <joel@jms.id.au>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Reviewed-by: NAndrew Jeffery <andrew@aj.id.au>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

probe_irq_off() returns '0' on failure, not NO_IRQ, so the check
in this driver is clearly wrong. This replaces it with the
regular '!irq' check used in other drivers.

The sa1100 platform that this driver is used on originally numbered
all its interrupts starting at '0', which would have conflicted with
this change, but as of commit 18f3aec3 ("ARM: 8230/1: sa1100: shift
IRQs by one"), this is not a problem any more.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Since the act8945a-charger is regarded as a sub-device and it using
"interrupts" property, update the examples section.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Bulk access is not working with twl6040, we need to use single register
access. Bulk access would happen when we try to sync the regcache after
power on.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As runtime PM doesn't function whilst processing system suspend/resume
operations and the Arizona IRQ handlers need runtime PM to function
we must disable IRQs during these operations. Whilst this is
already done in the driver we are using suspend/suspend_late and
resume/resume_noirq to do so which has two problems. Firstly, as
suspend_late is before suspend_noirq that means we still have a
small window where an IRQ can cause issues.  Secondly, if another
suspend_late handler fails after ours has run then (as resume_noirq
will not run) we will make unbalanced calls to enable_irq.

This is all simply fixed by using the suspend_noirq callback rather
than suspend_late. Whilst we are doing this tidy the code up a little,
and use the appropriate helper macros.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

To regard the act8945a-charger as a sub-device, add .of_compatible for
act8945a-charger cell.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

There are some cases in arizona_dev_init, such as where we don't
recognise the chip ID, in which we head to the error path without
setting a sensible error code in ret. This would lead to the chip
silently failing probe, as it would still return 0. Fix this up by
adding appropriate sets of the return value.

Whilst adding these update the existing paths that do return an error
when the chip is not recognised to use ENODEV, which seems like a better
fit.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds common driver for the Top block of the Samsung Exynos
SoC Low Power Audio Subsystem.  This is a minimal driver which prepares
resources for IP blocks like I2S, audio DMA and UART and exposes
a regmap for the Top block registers.  Also system power ops are added
to ensure the Audio Subsystem is operational after system suspend/resume
cycle.
Signed-off-by: NInha Song <ideal.song@samsung.com>
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds documentation of the DT bindings for the Samsung
Exynos SoC Low Power Audio Subsystem.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The function da9052_clear_fault_log() is added to mitigate the case of
persistent data being transferred between reboots.

Clearance of any the persistent information within the DA9053 FAULT_LOG
register must be completed during start-up so the fault-log does not
continue with previous values. A clearance function has been added here in
the kernel driver because wiping the fault-log cannot be counted on outside
the Linux kernel.
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: NAdam Thomson <adam.thomson.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Adjust jump targets according to the Linux coding style convention.
Another check for the variable "status" can be omitted then at the end.

Link: https://lkml.kernel.org/g/<20160628163146.GG29166@dell>
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Member "status" of struct usb_sg_request is managed by usb core. A
spin lock is used to serialize the change of it. The driver could
check the value of req->status, but should avoid changing it without
the hold of the spinlock. Otherwise, it could cause race or error
in usb core.

This patch could be backported to stable kernels with version later
than v3.14.

Cc: stable@vger.kernel.org # 3.14+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Roger Tseng <rogerable@realtek.com>
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

probe_irq_on() only returns non-zero if it found any interrupts below
IRQ32 which could be probe candidates.  If all the probable interrupts
are higher than 32, then this will cause a failure.  Fix this.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The MSM8660, APQ8060, IPQ806x and MSM8960 have a GCC clock
to the message RAM used by the RPM. This needs to be enabled
for messages to pass through. This is a crude solution that
simply prepare/enable at probe() and disable/unprepare
at remove(). More elaborate PM is probably possible to
add later.

The construction uses IS_ERR() to gracefully handle the
platforms that do not provide a message RAM clock. It will
bail out of probe only if the clock is hitting a probe
deferral situation.

Of course this requires the proper device tree set-up:

rpm: rpm@104000 {
    compatible = "qcom,rpm-msm8660";
    clocks = <&gcc RPM_MSG_RAM_H_CLK>;
    clock-names = "ram";
    ...
};

I have provided this in the MSM8660 device tree, and will
provide patches for the other targets.

Cc: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact.  The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The lp873x series of PMICs have a bunch of regulators and a couple
of GPO(General Purpose Outputs).
Add information for the MFD and regulator drivers.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Intel Whiskey Cove PMIC includes several function units, e.g.
ADC, thermal, USB Type-C, GPIO, etc. The corresponding device has
to be created in the mfd driver(intel_soc_pmic_bxtwc.c). This change
adds the USB Type-c device.
Signed-off-by: NBin Gao <bin.gao@intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Intel Kaby Lake PCH-H has the same LPSS than Intel Sunrisepoint. Add the new
IDs to the list of supported devices.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

set_bit() and clear_bit() take the bit number so this code is really
doing "1 << (1 << irq)" which is a double shift bug.  It's done
consistently so it won't cause a problem unless "irq" is more than 4.

Fixes: 70c6cce0 ('mfd: Support 88pm80x in 80x driver')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

It's only used in this driver and never get modified, make it static const.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Reviewed-by: NThor Thayer <tthayer@opensource.altera.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This fixes a compile failure:

	drivers/built-in.o: In function `wm8350_i2c_probe':
	core.c:(.text+0x828b0): undefined reference to `__devm_regmap_init_i2c'
	Makefile:953: recipe for target 'vmlinux' failed

Fixes: 52b461b8 ("mfd: Add regmap cache support for wm8350")
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Remove incorrect e-mail addresses from the copyright header and
MODULE_AUTHOR() macro. These e-mail addresses are no longer in use.

The author names have not been changed, only the e-mail addresses have
been deleted from the source files.
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Now that we have a GPIO driver for the AXP209, we can add it to our MFD.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Reviewed-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Merge branches 'ib-mfd-gpio-4.9', 'ib-mfd-gpio-regulator-4.9', 'ib-mfd-input-4.9', 'ib-mfd-regulator-4.9', 'ib-mfd-regulator-4.9.1', 'ib-mfd-regulator-rtc-4.9', 'ib-mfd-regulator-rtc-4.9-1' and 'ib-mfd-rtc-4.9' into ibs-for-mfd-merged

This patch adds requesting of the clocks supplied on MCLK1, MCLK2 pins,
gating of the 32k clock is added to the arizona_clk32k_enable(),
arizona_clk32k_disable() helpers.

It's a temporary change until the CODEC's clock controller gets exposed
through the clk API and is helpful for board configurations where the
MCLK clocks are not provided by always on oscillators.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
SoC, along with a master AXP809 PMIC.

This PMIC has a new register layout, and supports some functions not
seen in other X-Powers PMICs, such as master-slave mode, or having
multiple AXP806 PMICs on the same bus with address space extension,
or supporting both I2C and RSB mode. I2C has not been tested.

This patch adds support for the interrupts of the PMIC. A regulator
sub-device is enabled, but actual regulator support will come in a
later patch.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds the basic and regulator bindings for the X-Powers AXP806
PMIC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
also a switch. The buck regulators support teaming into multi-phase
groups, with A+B, A+B+C, D+E groupings.

Some registers controlling DCDC converter work settings are at different
offsets. Deal with them as well.

Add support for this new variant.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The RK808 and RK818 PMICs are using a similar register map.
We can reuse the rtc driver for the RK818 PMIC. So let's add
the RK818 in the Kconfig description.
Signed-off-by: NWadim Egorov <w.egorov@phytec.de>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>