We need to re-set tx moderation information after calling set_ringparam
else default tx moderation will be used.
Also avoid related code duplication, by putting it in a utility function.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set mlx4_en maintainer to Amir Vadai instead of Yevgeny Petrilin.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Woodhouse says:

====================
This is the result of pulling on the thread started by Krzysztof Mazur's
original patch 'pppoatm: don't send frames to destroyed vcc'.

Various problems in the pppoatm and br2684 code are solved, some of which
were easily triggered and would panic the kernel.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No idea why we've gone so long dumping a list of VCCs with vci==0 on
every ->open() call...
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

 - Flush pending TX skbs from the queue rather than waiting for them all to
   complete (suggested by Krzysztof Mazur <krzysiek@podlesie.net>).
 - Clear ATM_VF_ADDR only when the PKT_PCLOSE packet has been submitted.
 - Don't clear ATM_VF_READY at all — vcc_destroy_socket() does that for us.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

We don't need to schedule the wakeup tasklet on *every* unlock; only if we
actually blocked the channel in the first place.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Acked-by: NKrzysztof Mazur <krzysiek@podlesie.net>

The br2684 does not check if used vcc is in connected state,
causing potential Oops in pppoatm_send() when vcc->send() is called
on not fully connected socket.

Now br2684 can be assigned only on connected sockets; otherwise
-EINVAL error is returned.
Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

... and ensure that the next skb is set up for RX in the DMA case.
Signed-off-by: NNathan Williams <nathan@traverse.com.au>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The br2684 code used module_put() during unassignment from vcc with
hope that we have BKL. This assumption is no longer true.

Now owner field in atmvcc is used to move this module_put()
to vcc_destroy_socket().
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Acked-by: NKrzysztof Mazur <krzysiek@podlesie.net>

Now that we can return zero from pppoatm_send() for reasons *other* than
the queue being full, that means we can't depend on a subsequent call to
pppoatm_pop() waking the queue, and we might leave it stalled
indefinitely.

Use the ->release_cb() callback to wake the queue after the sock is
unlocked.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Acked-by: NKrzysztof Mazur <krzysiek@podlesie.net>

Avoid submitting packets to a vcc which is being closed. Things go badly
wrong when the ->pop method gets later called after everything's been
torn down.

Use the ATM socket lock for synchronisation with vcc_destroy_socket(),
which clears the ATM_VF_READY bit under the same lock. Otherwise, we
could end up submitting a packet to the device driver even after its
->ops->close method has been called. And it could call the vcc's ->pop
method after the protocol has been shut down. Which leads to a panic.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Acked-by: NKrzysztof Mazur <krzysiek@podlesie.net>

The immediate use case for this is that it will allow us to ensure that a
pppoatm queue is woken after it has to drop a packet due to the sock being
locked.

Note that 'release_cb' is called when the socket is *unlocked*. This is
not to be confused with vcc_release() — which probably ought to be called
vcc_close().
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Acked-by: NKrzysztof Mazur <krzysiek@podlesie.net>

We should no longer be calling the old pop routine for the vcc, after
vcc_release() has completed. Make sure we wait for any pending TX skbs
to complete, by waiting for our own PKT_PCLOSE control skb to be sent.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1b4c44e6 incorrectly used
ntohs() rather than htons() in myri10ge_vlan_rx().

Thanks to Fengguang Wu, Yuanhan Liu's kernel-build tester
for pointing out this bug.
Signed-off-by: NAndrew Gallatin <gallatin@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As of 026359bc [ipv6: Send ICMPv6 RSes only when RAs are accepted], the
logic determining whether to send Router Solicitations is identical
to the logic determining whether kernel accepts Router Advertisements.

However the condition itself is repeated in several code locations.

Unify it by introducing 'ipv6_accept_ra()' accessor.

Also, simplify the condition expression, making it more readable.
No semantic change.
Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As time passed, available memory increased faster than number of
concurrent tcp sockets.

As a result, a machine with 4GB of ram gets a hash table
with 524288 slots, using 8388608 bytes of memory.

Lets change that by a 16x factor (one slot for 128 KB of ram)

Even if a small machine needs a _lot_ of sockets, tcp lookups are now
very efficient, using one cache line per socket.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
1. More workarounds for TX queue flush failures that can occur during
   interface reconfiguration.
2. Fix spurious failure of a firmware request running during a system
   clock change, e.g. ntpd started at the same time as driver load.
3. Fix inconsistent statistics after a firmware upgrade.
4. Fix a variable (non-)initialisation in offline self-test that can
   make it more disruptive than intended.
5. Fix a race that can (at least) cause an assertion failure.
6. Miscellaneous cleanup.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to ixgbe, igb and e1000e.  Majority of the
changes are against igb.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that only the first fragment in a series of fragments
will have the L4 header pulled.  Previously we were always pulling the L4
header as well and in the case of UDP this can harm performance since only the
first fragment will have the header, the rest just contain data which should
be left in the paged portion of the packet.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update comments to conform to the preferred style for networking code as
described in ./Documentation/CodingStyle and checked for in the recently
added checkpatch NETWORKING_BLOCK_COMMENT_STYLE test.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables flow control to be set in SerDes autoneg mode.  This is
done the way it is done for copper, but relies on a different set of register/bit
checks since this is all done within the MAC registers.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch unsets the sigdetect bit for SERDES loopback tests on 82580 and
i350 parts.  The loopback test can fail on these parts without this
setting.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to a hw errata, the global device reset doesn't always work on 82580
devices.  This patch works around the problem not trying to do a global
device reset on these devices.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch refactors the functions in e1000_i210.c in order to remove need
for prototypes.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allows software acquires and releases NVM resource for
writing each EEPROM page, instead of holding semaphore for the whole
data block which is too long and could trigger write fails on
unpredictable addresses.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i211 has an integrated secure space to store configuration information that is
usually stored in an EEPROM or flash type device. This patch updates the
read functions to return values or appropriate error codes to prevent
unnecessary init failures on some configuration schemes.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch replaces calls to copy_to_user, copy_from_user, and the associated
logic, with calls to simple_read_from_buffer and simple_write_to_buffer
respectively.  This was done to eliminate warnings generated by the Smatch
static analysis tool.

v2- Fix return values based community feedback
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Most of the module parameters treated as boolean are currently exposed
as type int or uint.  Defining them with the proper type is useful
documentation for both users and developers.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_mcdi_poll() uses get_seconds() to read the current time and to
implement a polling timeout.  The use of this function was chosen
partly because it could easily be replaced in a co-sim environment
with a macro that read the simulated time.

Unfortunately the real get_seconds() returns the system time (real
time) which is subject to adjustment by e.g. ntpd.  If the system time
is adjusted forward during a polled MCDI operation, the effective
timeout can be shorter than the intended 10 seconds, resulting in a
spurious failure.  It is also possible for a backward adjustment to
delay detection of a areal failure.

Use jiffies instead, and change MCDI_RPC_TIMEOUT to be denominated in
jiffies.  Also correct rounding of the timeout: check time > finish
(or rather time_after(time, finish)) and not time >= finish.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The assertion of netif_device_present() at the top of
efx_hard_start_xmit() may fail if we don't do this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We sometimes hit a "failed to flush" timeout on some TX queues, but the
flushes have completed and the flush completion events seem to go missing.
In this case, we can check the TX_DESC_PTR_TBL register and drain the
queues if the flushes had finished.

[bwh: Minor fixes to coding style]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

If the MC reboots then the stats it reports to us will have been
reset.  We need to reset ours to get efx_update_diff_stat() working
properly.

(Ideally we would maintain stats across the reboot, but as this should
only happen immediately after a firmware upgrade it's not really worth
the trouble.)
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Currently we initialise the newly allocated buffer to all-1s, which is
important for event queues but not for descriptor queues.  And since
we also do that in efx_nic_init_eventq(), it is completely pointless
to do it here.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_writed_table() uses a step of 16 bytes but efx_readd_table() uses
a step of 4 bytes.  Why are they different?

Firstly, register access is asymmetric:

- The EVQ_RPTR table and RX_INDIRECTION_TBL can (or must?) be written
  as dwords even though they have a step size of 16 bytes, unlike
  most other CSRs.
- In general, a read of any width is valid for registers, so long as
  it does not cross register boundaries.  There is also no latching
  behaviour in the BIU, contrary to rumour.

We write to the EVQ_RPTR table with efx_writed_table() but never read
it back as it's write-only.  We write to the RX_INDIRECTION_TBL with
efx_writed_table(), but only read it back for the register dump, where
we use efx_reado_table() as for any other table with step size of 16.

We read MC_TREG_SMEM with efx_readd_table() for the register dump, but
normally read and write it with efx_readd() and efx_writed() using
offsets calculated in bytes.

Since these functions are trivial and have few callers, it's clearer
to open-code them at the call sites.  While we're at it, update the
comments on the BIU behaviour again.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_mcdi_rpc_start() returns a negative value on error or zero on
success.  However one caller that can't properly handle failure then
does WARN_ON(rc > 0).  Change it to WARN_ON(rc < 0).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Receiving pause frames can block TX queue flushes.  Earlier changes
work around this by reconfiguring the MAC during flushes for VFs, but
during flushes for the PF we would only change the fc_disable counter.
Unless the MAC is reconfigured for some other reason during the flush
(which I would not expect to happen) this had no effect at all.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>