Loading the cypress firmware is not dvb specific and should be common
functionality. Move the source to media/common and make it a standalone
module.
As a result we can remove the dependency on dvb-usb in go7007, which has
nothing to do with dvb.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

vidioc_s_tuner, vidioc_s_frequency and vidioc_s_register now
uses a constant argument. So, the driver reports warnings:

	drivers/media/radio/radio-si476x.c:1196:2: warning: initialization from incompatible pointer type [enabled by default]
	drivers/media/radio/radio-si476x.c:1196:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_tuner') [enabled by default]
	drivers/media/radio/radio-si476x.c:1199:2: warning: initialization from incompatible pointer type [enabled by default]
	drivers/media/radio/radio-si476x.c:1199:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_frequency') [enabled by default]
	drivers/media/radio/radio-si476x.c:1209:2: warning: initialization from incompatible pointer type [enabled by default]
	drivers/media/radio/radio-si476x.c:1209:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_register') [enabled by default]

This is due to a (soft) merge conflict, as both this driver and the
const patches were applied for the same Kernel version.

Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This commit adds a driver that exposes all the radio related
functionality of the Si476x series of chips via the V4L2 subsystem.
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a base to be used for allocation of all the SI476X specific
controls in the corresponding driver.
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add appropriate documentation for all the newly added standard
controls.
Based on the patch by Manjunatha Halli [1]
[1] http://lists-archives.com/linux-kernel/27641303-media-update-docs-for-v4l2-fm-new-features.htmlAcked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This commit introduces new class of standard controls
V4L2_CTRL_CLASS_FM_RX. This class is intended to all controls
pertaining to FM receiver chips. Also, two controls belonging to said
class are added as a part of this commit: V4L2_CID_TUNE_DEEMPHASIS and
V4L2_CID_RDS_RECEPTION.
This patch is based on the code found in the patch by Manjunatha Halli [1]
[1] http://lists-archives.com/linux-kernel/27641307-new-control-class-and-features-for-fm-rx.htmlAcked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change the type of V4L2_CID_TUNE_PREEMPHASIS from 'integer' to 'enum
v4l2_preemphasis'
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds all necessary header files and Kbuild plumbing for the
core driver for Silicon Laboratories Si476x series of AM/FM tuner
chips.
The driver as a whole is implemented as an MFD device and this patch
adds a core portion of it that provides all the necessary
functionality to the two other drivers that represent radio and audio
codec subsystems of the chip.
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds code related to manipulation of the properties of
SI476X chips.
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds main part(out of three) of the I2C driver for the
"core" of MFD device.
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds all the functions used for exchanging commands with
the chip.
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On powerpc the maximum size for the ioctl argument is 8191, and it was
8192. However, the 64x64 array of threshold values is more than is actually
needed in practice for PAL and NTSC formats. A 45x45 array will do just fine.
So change the size accordingly to fix this problem.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If i run verbose v4l2-compliance with my radio-mr800 device few times
then i get warning about frequency out of range:

root@machine:~# v4l2-compliance -r /dev/radio0 -v 2
is radio
Driver Info:
	Driver name   : radio-mr800
	Card type     : AverMedia MR 800 USB FM Radio
	Bus info      : usb-0000:00:1a.0-1.2
	Driver version: 3.9.0
	Capabilities  : 0x80050400
		Tuner
		Radio
		Device Capabilities
	Device Caps   : 0x00050400
		Tuner
		Radio
Compliance test for device /dev/radio0 (not using libv4l2):
Required ioctls:
	test VIDIOC_QUERYCAP: OK
Allow for multiple opens:
	test second radio open: OK
	test VIDIOC_QUERYCAP: OK
	test VIDIOC_G/S_PRIORITY: OK
Debug ioctls:
	test VIDIOC_DBG_G_CHIP_IDENT: OK (Not Supported)
	test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
	test VIDIOC_LOG_STATUS: OK
Input ioctls:
	test VIDIOC_G/S_TUNER: OK
		warn: v4l2-test-input-output.cpp(234): returned tuner 0 frequency out
of range (6550200 not in [1400000...1728000])
	test VIDIOC_G/S_FREQUENCY: OK
	test VIDIOC_S_HW_FREQ_SEEK: OK
	test VIDIOC_ENUMAUDIO: OK (Not Supported)
	test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
	test VIDIOC_G/S_AUDIO: OK (Not Supported)
	Inputs: 0 Audio Inputs: 0 Tuners: 1
Output ioctls:
	test VIDIOC_G/S_MODULATOR: OK (Not Supported)
	test VIDIOC_G/S_FREQUENCY: OK
	test VIDIOC_ENUMAUDOUT: OK (Not Supported)
	test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
	test VIDIOC_G/S_AUDOUT: OK (Not Supported)
	Outputs: 0 Audio Outputs: 0 Modulators: 0
Control ioctls:
		info: checking v4l2_queryctrl of control 'User Controls' (0x00980001)
		info: checking v4l2_queryctrl of control 'Mute' (0x00980909)
		info: checking v4l2_queryctrl of control 'Mute' (0x00980909)
	test VIDIOC_QUERYCTRL/MENU: OK
		info: checking control 'User Controls' (0x00980001)
		info: checking control 'Mute' (0x00980909)
	test VIDIOC_G/S_CTRL: OK
		info: checking extended control 'User Controls' (0x00980001)
		info: checking extended control 'Mute' (0x00980909)
	test VIDIOC_G/S/TRY_EXT_CTRLS: OK
		info: checking control event 'User Controls' (0x00980001)
		info: checking control event 'Mute' (0x00980909)
	test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
	test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
	Standard Controls: 2 Private Controls: 0
Input/Output configuration ioctls:
	test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
	test VIDIOC_ENUM/G/S/QUERY_DV_PRESETS: OK (Not Supported)
	test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
	test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
Format ioctls:
	test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported)
	test VIDIOC_G/S_PARM: OK (Not Supported)
	test VIDIOC_G_FBUF: OK (Not Supported)
	test VIDIOC_G_FMT: OK (Not Supported)
	test VIDIOC_TRY_FMT: OK (Not Supported)
	test VIDIOC_S_FMT: OK (Not Supported)
	test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
Codec ioctls:
	test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
	test VIDIOC_G_ENC_INDEX: OK (Not Supported)
	test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
Buffer ioctls:
	test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported)
Total: 38, Succeeded: 38, Failed: 0, Warnings: 1

Some printk() debugging showed that vidioc_s_hw_freq_seek() setups
radio->curfreq to out of range value (lines 395-396) and calls
amradio_set_freq() to set this frequency on device without any
out-of-range checks.

Patch protects from setting up frequency on device to incorrect value
moving clamp_t check inside amradio_set_freq. With this patch we can
call amradio_set_freq() with out of range frequency from any place.
Also put comment that sometimes radio->curfreq is set to out of range
value in vidioc_s_hw_freq_seek().
Signed-off-by: NAlexey Klimov <klimov.linux@gmail.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The et61x251 driver was removed in v3.5. Remove the last references to
its Kconfig macro now.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

ioctl's number is unsigned int. Fix it at vidioc_default.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Correct spelling typo in staging/media/davinci
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This sensor is used by the "SpeedLink Vicious And Devine Laplace webcam" and
others. It supports resolutions up to 1600x1200 (at 7-8 fps), but for
resolutions higher than 640x480, further driver changes will be necessary,
such as sensor output resolution switching (including further configuration
changes), bridge xclk adjustment and disabling of 16 bit (12 bit) output formats
at high resolutions. Image quality should also needs to be improved.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Windows driver also probes at least two further i2c addresses (0x22 >> 1
and 0x66 >> 1). I've got some hints that they are very likely used by Samsung
and Kodak sensors, which are known to be used in Empia devices, too.
We havn't seen any devices using these sensors yet and don't know how to probe
them properly, so leave a comment.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

OmniVision sensors are used as well in Empiatech based cameras such as the
"SpeedLink Vicious And Devine Laplace" webcam (EM2765 + Omnivision OV2640).
With this patch applied, OminiVision sensors with 8 bit address and register
width are detected (recent models have a 16 bit address width and use different
client addresses).
The most commonly used sensors (including the ones listed by Empiatech) are
detected properly, although there is no support for them yet.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Other sensors like the ones from OmniVision need a different probing procedure,
so it makes sense have separate functions for each manufacturer/sensor type.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add further Micron chip IDs to be able to identify all Micron sensors listed
by Empiatech.
Also probe the two alternate i2c addresses used by Micron sensors with 8 bit
address and 16 bit register width.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

em28xx-cards.c is very large and the sensor/camera related code is growing,
so move this code to a separate source code file em28xx-camera.c.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now that the board hints and the sensor initialization/configuration have been
separated, em28xx_detect_sensor() is the better name for this function.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Sensor detection and initialization/configuration are currently mixed together.
This works as long as all devices with a particular sensor are working with the
same board configuration. In the long run, this will be not sufficient, so
separate these both steps to make the code more flexible and future proof.
This also makes the code more consistent, because the initialization of the
MT9V011 sensor subdevice is already separated.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The current board hint code is mixed together with the sensor detection and
initialization code. It actually selects a board depending on the detected
sensor type only, with the result that 3 of the 6 webcam boards are currently
dead.
Separate it and move it to em28xx_hint_board() which already contains the board
hints for analog capturing+TV and DVB devices.
This way, we have all board hints at a common place which makes it easier
to extend the code and reduces the risk of regressions.
It also makes it possible again to use the boards EM2750_BOARD_DLCW_130,
EM2820_BOARD_VIDEOLOGY_20K14XUSB and EM2860_BOARD_NETGMBH_CAM (using the module
parameter "card").
NOTE: the current board hint logic for webcams is preserved. Not more not less.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some devices without DVB support (such as the "Terratec Grabby" and
"Easycap DC-60") provide isochronous DVB USB endpoints with wMaxPacketSize set
to 0 bytes for all alt settings.
Ignore these endpoints and avoid registering a DVB device node and loading the
DVB driver extension.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: NTimo Teräs <timo.teras@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

-ERANGE is the right error code when the value is outside of the menu
range, but -EINVAL must be reported for invalid values inside the range.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Windows driver writes the output resolution to registers 0x34 (width / 16)
and 0x35 (height / 16) always.
We don't know yet what these registers are used for.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Streaming doesn't work with the EM2765 if bit 5 of the output format register
0x27 is set.
It's actually not clear if really has to be set for the other chips, but for
now let's keep it to avoid regressions and add a comment to the code.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The em25xx/em276x/em277x/em278x frame data format is different to the one used
by the em2710/em2750/em28xx chips.
With the recent cleanups and reorganization of the frame data processing code it
can be easily extended to support these devices.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This chip can be found in the SpeedLink VAD Laplace webcam (1ae7:9003 and 1ae7:9004).
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The webcam "SpeedLink VAD Laplace" (em2765 + ov2640) uses a special algorithm
for i2c communication with the sensor, which is connected to a second i2c bus.
We don't know yet how to find out which devices support/use it.
It's very likely used by all em25xx and em276x+ bridges.
Tests with other em28xx chips (em2820, em2882/em2883) show, that this
algorithm always succeeds there although no slave device is connected.
The algorithm likely also works for real i2c client devices (OV2640 uses SCCB),
because the Windows driver seems to use it for probing Samsung and Kodak
sensors.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

au8522_attach is dependent on CONFIG_DVB_AU8522_DTV, not CONFIG_DVB_AU8522.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the missing unlock before return from function af9035_ctrl_msg()
in the error handling case.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NAntti Palosaari <crope@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If those callbacks fail, it should return zero, and not a random
value. The previous code assumed that all drivers would only change
signal strength if it succeeds, but this may not be true.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now that those functions are only used when the corresponding
function calls are defined, we don't need to check if those
function calls are present at the structure before using it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

While the driver gets AFC from the tuner, it doesn't return it
back via V4L2 API due to a mistake at the return. fix it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If the tuner frontend does not support get_rf_strength, then don't set
the has_signal callback. Ditto for get_afc.
Both callbacks overwrite the signal and afc fields of struct v4l2_tuner
but that should only happen if the tuner can actually detect this. If
it can't, then it should leave those fields alone so other subdevices
can try and detect the signal/afc.
This fixes the bug where the au8522 detected a signal and then tuner-core
overwrote it with 0 since the xc5000 tuner does not support get_rf_strength.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- open/close/read and poll need to take the core lock as well.
- when the tuner goes to sleep we should set std_set_in_tuner_core
  to 0 since the tuner loses the firmware at that time.
- initialize the tuner if std_set_in_tuner_core == 0 whenever:
  1) g/s_tuner, s_std or s_frequency is called
  2) read or poll is called
  3) streamon is called
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>