DDI A and E have 4 lanes to share, so if DDI A is using 4 lanes,
there's nothing left for DDI E, which means there's no CRT port on the
machine.

The bit we're checking here is programmed at system boot and it cannot
be changed afterwards, so we cannot change the amount of lanes
reserved for each DDI port.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to enable a special bit, otherwise none of the DP functions
requiring the PCH will work.

Version 2: store the PCH ID inside dev_priv, as suggested by Daniel
Vetter.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We don't check if the "unclaimed register" bit is set before we call
writel, so if it was already set before, we might print a misleading
message about "unclaimed write" on the wrong register.

This patch makes us check the unclaimed bit before the writel, so we
can print a new "Unknown unclaimed register before writing to %x"
message.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function runs on Haswell, so set the correct pch_transcoder and
cpu_transcoder variables. This fixes an assertion failure on Haswell
VGA.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is a full revert of 59c859d6:
    drm/i915: account for only one PCH receiver on Haswell

Now that the PCH code is fixed to be able use the only PCH transcoder
independently of the pipe and CPU transcoder, we can revert this.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Resolve conflict due to the rebasing of dinq on top of
drm-next.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we accumulate unpin tasks because we are pageflipping faster than the
system can schedule its workers, we can effectively create a
pin-leak. The solution taken here is to limit the number of unpin tasks
we have per-crtc and to flush those outstanding tasks if we accumulate
too many. This should prevent any jitter in the normal case, and also
prevent the hang if we should run too fast.

Note: It is important that we switch from the system workqueue to our
own dev_priv->wq since all work items on that queue are guaranteed to
only need the dev->struct_mutex and not any modeset resources. For
otherwise if we have a work item ahead in the queue which needs the
modeset lock (like the output detect work used by both polling or
hpd), this work and so the unpin work will never execute since the
pageflip code already holds that lock. Unfortunately there's no
lockdep support for this scenario in the workqueue code.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46991Reported-and-tested-by: NTvrtko Ursulin <tvrtko.ursulin@onelan.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Added note about workqueu deadlock.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56337Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

But disabled by default. This essentially reverts

commit bcd5023c
Author: Dave Airlie <airlied@redhat.com>
Date:   Mon Mar 14 14:17:55 2011 +1000

    drm/i915: disable opregion lid detection for now

but leaves the autodetect mode disabled. There's also the explicit lid
status option added in

commit fca87409
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Thu Feb 17 13:44:48 2011 +0000

    drm/i915: Add a module parameter to ignore lid status

Which overloaded the meaning for the panel_ignore_lid parameter even
more. To fix up this mess, give the non-negative numbers 0,1 the
original meaning back and use negative numbers to force a given state.
So now we have

1  - disable autodetect, return unknown
0  - enable autodetect
-1 - force to disconnected/lid closed
-2 - force to connected/lid open

v2: My C programmer license has been revoked ...

v3: Beautify the code a bit, as suggested by Chris Wilson.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=27622Tested-by: NAndreas Sturmlechner <andreas.sturmlechner@gmail.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch adds the missing code to send ELD for Haswell DisplayPort,
based on Xingchao's original patch.

A test was performed with HSW-D machine and NEC EA232Wmi DP monitor.

Cc: Xingchao Wang <xingchao.wang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In order to prevent reaping of the object whilst setting it up to
handle the pagefault, we need to mark it as pinned. This has the nice
side-effect of eliminating some special cases from the pagefault handler
as well!
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the circumstances that the shrinker is allowed to steal the mutex
in order to reap pages, we need to be careful to prevent it operating on
the current object and shooting ourselves in the foot.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The intention of checking obj->gtt_offset!=0 is to verify that the
target object was listed in the execbuffer and had been bound into the
GTT. This is guarranteed by the earlier rearrangement to split the
execbuffer operation into reserve and relocation phases and then
verified by the check that the target handle had been processed during
the reservation phase.

However, the actual checking of obj->gtt_offset==0 is bogus as we can
indeed reference an object at offset 0. For instance, the framebuffer
installed by the BIOS often resides at offset 0 - causing EINVAL as we
legimately try to render using the stolen fb.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that we always restore the HWS registers (both physical and GTT
virtual addresses) when re-initialising the rings, we can eliminate the
superfluous save/restore of the register across suspend and resume.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

drivers/gpu/drm/i915/i915_drv.h:1545:2: warning: '______f' is static but
declared in inline function 'i915_gem_chipset_flush' which is not static
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
dri-devel-Reference: <50a4d41c.586VhmwghPuKZbkB%fengguang.wu@intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

ILK+ have this register on the PCH. This check was triggering unclaimed
writes.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Jani Nikula noticed that the parentheses are wrong and we & the bit
with the register address instead of the read-back value. He sent a
patch to correct that.

On second look, we write the same register in the previous line, and
the w/a seems to be to set FDI_RX_PHASE_SYNC_POINTER_OVR to enable the
logic, then keep always set FDI_RX_PHASE_SYNC_POINTER_OVR and toggle
FDI_RX_PHASE_SYNC_POINTER_EN before/after enabling the pc transcoder.

So the right things seems to be to simply kill the 2nd write.

Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Dropped a bogus ~ from the commit message that somehow crept
in.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The bspec was recently updated to remove the ability to update the
semaphore using the MI_SEMAPHORE_BOX command, the ability to wait upon
the semaphore value remained. Instead the advice is to update the
register using the MI_LOAD_REGISTER_IMM command. In cursory testing,
semaphores continue to function - the question is whether this fixes
some of the deadlocks where the semaphore registers contained stale
values?
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel J Blueman <daniel@quora.org>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

[pzanoni: rebase, print it's an LP PCH]
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

DIV_ROUND_CLOSEST is faster if the compiler knows it will only be
dealing with unsigned dividends. This optimization rips 32 bytes of
binary code on x86_64.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NBrian Paul <brianp@vmware.com>
Reviewed-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This also fixes a bug where the fence manager was left without irq
enabled when waiting for fences, causing various errors at module
load time
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NBrian Paul <brianp@vmware.com>
Reviewed-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NBrian Paul <brianp@vmware.com>
Reviewed-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NBrian Paul <brianp@vmware.com>
Reviewed-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Hiding SVGA seems to trigger a VGA screen clear, and with no
traces dirty it doesn't seem to repaint
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NBrian Paul <brianp@vmware.com>
Reviewed-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is similar to other platforms that don't allow command submission
to buffers locked on the cpu.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Reservation locking currently always takes place under the LRU spinlock.
Hence, strictly there is no need for an atomic_cmpxchg call; we can use
atomic_read followed by atomic_write since nobody else will ever reserve
without the lru spinlock held.
At least on Intel this should remove a locked bus cycle on successful
reserve.

Note that thit commit may be obsoleted by the cross-device reservation work.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The mostly used lookup+get put+potential_destroy path of TTM objects
is converted to use RCU locks. This will substantially decrease the amount
of locked bus cycles during normal operation.
Since we use kfree_rcu to free the objects, no rcu synchronization is needed
at module unload time.

v2: Don't touch include/linux/kref.h
v3: Adapt to kref_get_unless_zero return value change
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This function is intended to simplify locking around refcounting for
objects that can be looked up from a lookup structure, and which are
removed from that lookup structure in the object destructor.
Operations on such objects require at least a read lock around
lookup + kref_get, and a write lock around kref_put + remove from lookup
structure. Furthermore, RCU implementations become extremely tricky.
With a lookup followed by a kref_get_unless_zero *with return value check*
locking in the kref_put path can be deferred to the actual removal from
the lookup structure and RCU lookups become trivial.

v2: Formatting fixes.
v3: Invert the return value.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

TTM base objects will be the first consumer.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-By: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-By: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

vmwgfx was its only user and always sets it to the same..
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-By: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It's always hardcoded to the same value.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-By: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When trying to obtain an accurate timestamp for the last vsync interrupt
in vblank_disable_and_save() we loop until the vsync counter after reading
the time stamp is identical to the one before.
In the case where no hardware timestamp can be obtained there is probably
no point in trying to make sure we remain within the same vsync during
the time we obtain the counter.
Furthermore we should make sure there's an 'emergency exit' so that we
don't end up in an endless loop when the driver get_vblank_timestamp()
function doesn't manage to return within the same vsync.
This may happen when this function prints out debugging information over
a slow (ie serial) line.
Signed-off-by: NEgbert Eich <eich@suse.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

... by properly checking connector->polled. This doesn't matter too
much because the polling work itself gets this slightly more right and
doesn't set repoll if there's nothing to do. But we can do better.

v2: Chris Wilson noticed that I broke polling, since repoll will never
ever be set true. Fix this up, and simplify the logic a bit while at
it.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NIgor Murzov <e-mail@date.by>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fix a memory leak by deallocating the memory we got from
alloc_apertures().
Signed-off-by: NTommi Rantala <tt.rantala@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Check for alloc_apertures() memory allocation failure, and propagate an
error code in case the allocation failed.
Signed-off-by: NTommi Rantala <tt.rantala@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

alloc_apertures() already does the assignment for us, so assigning the
count member after the alloc_apertures() call is not needed.
Signed-off-by: NTommi Rantala <tt.rantala@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fix a memory leak by deallocating the memory we got from
alloc_apertures().
Signed-off-by: NTommi Rantala <tt.rantala@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Check for alloc_apertures() memory allocation failure, and propagate an
error code in case the allocation failed.
Signed-off-by: NTommi Rantala <tt.rantala@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>