Add complete bindings to instantiate and configure the codec and
top-level audio complex on all currently supported boards using the
Tegra+WM8903 audio driver.

On those boards, disable the I2S2 controller since it isn't used.

On boards not using the WM8903 codec, disable all the audio devices;
they can be re-enabled once the relevant codec and ASoC machine drivers
have been ported to device-tree.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Mark any SDHCI controllers that aren't registered by the board files as
disabled in the device-tree files.

In practice, these controllers:

* Have nothing hooked up to them at all, or
* For ports intended for SDIO usage, the drivers for anything that might
  be attached are not in the device-tree yet. If/when drivers appear, the
  SD/MMC port can be re-enabled.

The only possible exception is TrimSlice's mico SD slot, but that wasn't
enabled in the board files before anyway, and doesn't work when all the
SDHCI controllers are enabled anyway.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Mark any serial ports that aren't registered by the board files as disabled
in the device-tree files.

In practice, none of the now-disabled ports ended up succeeding device
probing because of the missing clock-frequency property. However,
explicitly marking the devices disabled has the advantage of squashing
the dev_warn() the failed probe causes, and documenting that we intend
the port not to be used, rather than accidentally left out the property.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

With board files, all I2C busses run at 400KHz. Fix the device-tree
to be consistent with this. It's possible this is incorrect, but at
least it keeps the board files and device-tree consistent.

Also, disable any I2C controllers that the board files don't register,
also for consistency.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The command-lines present in the existing /chosen node are not necessarily
correct for all users. Ideally, we should simply use the command-line
supplied by the boot-loader.

In fact, using the boot-loader's cmdline is quite easy; either the
bootloader fully supports DT, in which case it can modify the DT passed
to the kernel to include its command-line, or CONFIG_APPENDED_DTB can
be used in conjunction with CONFIG_ARM_ATAG_DTB_COMPAT, and the kernel
will substitute the bootloader's command-line into the DT.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

There are no drivers in the kernel at present which can make use of the
memory reserved by /memreserve/, so there is no point reserving it. Remove
/memreserve/ to allow the user more memory. It's also unclear whether any
future driver would actually require /memreserve/, or allocate memory
through some other mechanism.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

* Add device-tree file for TrimSlice
* Add that to the list of .dts files to build
* Update board-dt.c to recognize TrimSlice board name

v2: Makefile: Add board-trimslice-pinmux.c to obj-$(CONFIG_MACH_TEGRA_DT).
v3: Makefile: Use brackets not braces around var names
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>