[ Upstream commit 5ab99cf7d5e96e3b727c30e7a8524c976bd3723d ]

The PVDD_APIO_1V8 (LDO2) and PVDD_ABB_1V8 (LDO8) regulators were turned
off by Linux kernel as unused.  However they supply critical parts of
SoC so they should be always on:

1. PVDD_APIO_1V8 supplies SYS pins (gpx[0-3], PSHOLD), HDMI level shift,
   RTC, VDD1_12 (DRAM internal 1.8 V logic), pull-up for PMIC interrupt
   lines, TTL/UARTR level shift, reset pins and SW-TACT1 button.
   It also supplies unused blocks like VDDQ_SRAM (for SROM controller) and
   VDDQ_GPIO (gpm7, gpy7).
   The LDO2 cannot be turned off (S2MPS11 keeps it on anyway) so
   marking it "always-on" only reflects its real status.

2. PVDD_ABB_1V8 supplies Adaptive Body Bias Generator for ARM cores,
   memory and Mali (G3D).
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b00ef53053191d3025c15e8041699f8c9d132daf ]

It must be made sure that immediate mode is not already set, when
modifying shadow register value in ehrpwm_pwm_disable(). Otherwise
modifications to the action-qualifier continuous S/W force
register(AQSFRC) will be done in the active register.
This may happen when both channels are being disabled. In this case,
only the first channel state will be recorded as disabled in the shadow
register. Later, when enabling the first channel again, the second
channel would be enabled as well. Setting RLDCSF to zero, first, ensures
that the shadow register is updated as desired.

Fixes: 38dabd91 ("pwm: tiehrpwm: Fix disabling of output of PWMs")
Signed-off-by: NChristoph Vogtländer <c.vogtlaender@sigma-surface-science.com>
[vigneshr@ti.com: Improve commit message]
Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 5ba846b1ee0792f5a596b9b0b86d6e8cdebfab06 ]

Intel IOMMU, when enabled, tries to find the domain of the device,
assuming it's a PCI one, during DMA operations, such as mapping or
unmapping. Since we are splitting the actual PCI device to couple of
children via MFD framework (see drivers/mfd/intel-lpss.c for details),
the DMA device appears to be a platform one, and thus not an actual one
that performs DMA. In a such situation IOMMU can't find or allocate
a proper domain for its operations. As a result, all DMA operations are
failed.

In order to fix this, supply parent of the platform device
to the DMA engine framework and fix filter functions accordingly.

We may rely on the fact that parent is a real PCI device, because no
other configuration is present in the wild.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NMark Brown <broonie@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [for tty parts]
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 203a068ac9e2722e4d118116acaa3a5586f9468a ]

Currently we aren't checking for the ICE_FC_NONE case for the current
flow control mode. This is causing "Unknown" to be printed for the
current flow control method if flow control is disabled. Fix this by
adding the case for ICE_FC_NONE to print "None".
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit da38ef3ed10a09248e13ae16530c2c6d448dc47d ]

We are currently assuming all GPIOs are non-wakeup capable GPIOs as we
not configuring the bank->non_wakeup_gpios like we used to earlier with
platform_data.

Let's add omap_gpio_is_off_wakeup_capable() to make the handling clearer
while considering that later patches may want to configure SoC specific
bank->non_wakeup_gpios for the GPIOs in wakeup domain.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Reported-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 699ca30162686bf305cdf94861be02eb0cf9bda2 ]

If __get_free_pages() fails, return -ENOMEM to avoid a NULL pointer
dereference.
Signed-off-by: NKangjie Lu <kjlu@umn.edu>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NSteven Price <steven.price@arm.com>
Reviewed-by: NMukesh Ojha <mojha@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 778c02a236a8728bb992de10ed1f12c0be5b7b0e ]

If a sync bfq_queue has a higher weight than some other queue, and
remains temporarily empty while in service, then, to preserve the
bandwidth share of the queue, it is necessary to plug I/O dispatching
until a new request arrives for the queue. In addition, a timeout
needs to be set, to avoid waiting for ever if the process associated
with the queue has actually finished its I/O.

Even with the above timeout, the device is however not fed with new
I/O for a while, if the process has finished its I/O. If this happens
often, then throughput drops and latencies grow. For this reason, the
timeout is kept rather low: 8 ms is the current default.

Unfortunately, such a low value may cause, on the opposite end, a
violation of bandwidth guarantees for a process that happens to issue
new I/O too late. The higher the system load, the higher the
probability that this happens to some process. This is a problem in
scenarios where service guarantees matter more than throughput. One
important case are weight-raised queues, which need to be granted a
very high fraction of the bandwidth.

To address this issue, this commit lower-bounds the plugging timeout
for weight-raised queues to 20 ms. This simple change provides
relevant benefits. For example, on a PLEXTOR PX-256M5S, with which
gnome-terminal starts in 0.6 seconds if there is no other I/O in
progress, the same applications starts in
- 0.8 seconds, instead of 1.2 seconds, if ten files are being read
  sequentially in parallel
- 1 second, instead of 2 seconds, if, in parallel, five files are
  being read sequentially, and five more files are being written
  sequentially
Tested-by: NHolger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: NOleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: NPaolo Valente <paolo.valente@linaro.org>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1d84353d205a953e2381044953b7fa31c8c9702d ]

In case ioremap fails, the fix releases resources and returns
-ENOMEM to avoid NULL pointer dereferences.
Signed-off-by: NKangjie Lu <kjlu@umn.edu>
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[b.zolnierkie: minor patch summary fixup]
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit ec7f6aad57ad29e4e66cc2e18e1e1599ddb02542 ]

When ioremap fails, hga_vram should not be dereferenced. The fix
check the failure to avoid NULL pointer dereference.
Signed-off-by: NKangjie Lu <kjlu@umn.edu>
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: Ferenc Bakonyi <fero@drama.obuda.kando.hu>
[b.zolnierkie: minor patch summary fixup]
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 0257eda08e806b82ee1fc90ef73583b6f022845c ]

Driver maintains state machine for processing and completing switch
commands. This patch resets FCF_ASYNC_{SENT|ACTIVE} flag to indicate if the
previous command is active or sent, in order for next GPSC command to
advance the state machine.

[mkp: commit desc typo]
Signed-off-by: NGiridhar Malavali <gmalavali@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 954b4b752a4c4e963b017ed8cef4c453c5ed308d ]

The MSI message address in the RC address space can be 64 bit. The
R-Car PCIe RC supports such a 64bit MSI message address as well.
The code currently uses virt_to_phys(__get_free_pages()) to obtain
a reserved page for the MSI message address, and the return value
of which can be a 64 bit physical address on 64 bit system.

However, the driver only programs PCIEMSIALR register with the bottom
32 bits of the virt_to_phys(__get_free_pages()) return value and does
not program the top 32 bits into PCIEMSIAUR, but rather programs the
PCIEMSIAUR register with 0x0. This worked fine on older 32 bit R-Car
SoCs, however may fail on new 64 bit R-Car SoCs.

Since from a PCIe controller perspective, an inbound MSI is a memory
write to a special address (in case of this controller, defined by
the value in PCIEMSIAUR:PCIEMSIALR), which triggers an interrupt, but
never hits the DRAM _and_ because allocation of an MSI by a PCIe card
driver obtains the MSI message address by reading PCIEMSIAUR:PCIEMSIALR
in rcar_msi_setup_irqs(), incorrectly programmed PCIEMSIAUR cannot
cause memory corruption or other issues.

There is however the possibility that if virt_to_phys(__get_free_pages())
returned address above the 32bit boundary _and_ PCIEMSIAUR was programmed
to 0x0 _and_ if the system had physical RAM at the address matching the
value of PCIEMSIALR, a PCIe card driver could allocate a buffer with a
physical address matching the value of PCIEMSIALR and a remote write to
such a buffer by a PCIe card would trigger a spurious MSI.

Fixes: e015f88c ("PCI: rcar: Add support for R-Car H3 to pcie-rcar")
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f0d14edd2ba43b995bef4dd5da5ffe0ae19321a1 ]

In case __get_free_pages() fails and returns NULL, fix the return
value to -ENOMEM and release resources to avoid dereferencing a
NULL pointer.
Signed-off-by: NKangjie Lu <kjlu@umn.edu>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NUlrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 72110b567479f0282489a9b3747e76d8c67d75f5 ]

When set 2 same MAC to different function of one port, IMP
will return error as the later one may modify the origin one.
This will cause bond fail for 2 VFs of one port.

Driver just print warning and return 0 with this patch, so
if set same MAC address, it will return 0 but do not really
configure HW.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 0cd0e49711556d2331a06b1117b68dd786cb54d2 ]

Call order on probe():
- max14656_hw_init() enables interrupts on the chip
- devm_request_irq() starts processing interrupts, isr
  could be called immediately
-    isr: schedules delayed work (irq_work)
-    irq_work: calls power_supply_changed()
- devm_power_supply_register() registers the power supply

Depending on timing, it's possible that power_supply_changed()
is called on an unregistered power supply structure.

Fix by registering the power supply before requesting the irq.

Cc: Alexander Kurz <akurz@blala.de>
Signed-off-by: NSven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e61985d0550df8c2078310202aaad9b41049c36c ]

If punit or telemetry device initialization fails, pmc driver should
unregister and return failure.

This change is to fix a kernel panic when removing kernel module
intel_pmc_ipc.

Fixes: 48c19170 ("platform:x86: Add Intel telemetry platform device")
Signed-off-by: NJunxiao Chang <junxiao.chang@intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 72aff4ecf1cb85a3c6e6b42ccbda0bc631b090b3 ]

This area is used to store keys by HSPPA in case of AM438x SOC. Leave it
active.
Signed-off-by: NKabir Sahane <x0153567@ti.com>
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a1e07ba89d49581471d64c48152dbe03b42bd025 ]

[Why]
The input color space for the plane was previously ignored even if it
was set.

If a limited range YUV format was given to DC then the
wrong color transformation matrix was being used since DC assumed that
it was full range instead.

[How]
Respect the given color_space format for the plane if it isn't
COLOR_SPACE_UNKNOWN. Otherwise, use the implicit default since DM
didn't specify.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NSun peng Li <Sunpeng.Li@amd.com>
Acked-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit fb26228bfc4ce3951544848555c0278e2832e618 ]

The find_dlpar_node() helper returns a device node with its reference
incremented.  Both the add and remove paths use this helper for find the
appropriate node, but fail to release the reference when done.

Annotate the find_dlpar_node() helper with a comment about the incremented
reference count and call of_node_put() on the obtained device_node in the
add and remove paths.  Also, fixup a reference leak in the find_vio_slot()
helper where we fail to call of_node_put() on the vdevice node after we
iterate over its children.
Signed-off-by: NTyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b14c872eebc501b9640b04f4a152df51d6eaf2fc ]

Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6QDL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality(this at least
breaks RAVE SP serdev driver on RDU2). Fix the code to specify
IMX6QDL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting incorrect
clock ratio.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8979117765c19edc3b01cc0ef853537bf93eea4b ]

Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SX_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SX_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 7b3132ecefdd1fcdf6b86e62021d0e55ea8034db ]

Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6UL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6UL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 412b032a1dc72fc9d1c258800355efa6671b6315 ]

Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX7D_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX7D_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c5ed5daa65d5f665e666b76c3dbfa503066defde ]

Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SLL_CLK_SDMA result in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SLL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit cc839d0f8c284fcb7591780b568f13415bbb737c ]

Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SL_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 28c168018e0902c67eb9c60d0fc4c8aa166c4efe ]

Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b7b4fda2636296471e29b78c2aa9535d7bedb7a0 ]

Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 918bbde8085ae147a43dcb491953e0dd8f3e9d6a ]

Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Angus Ainslie (Purism) <angus@akkea.ca>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit bbdc00a7de24cc90315b1775fb74841373fe12f7 ]

The rk3288 SoC has two PWM implementations available, the "old"
implementation and the "new" one.  You can switch between the two of
them by flipping a bit in the grf.

The "old" implementation is the default at chip power up but isn't the
one that's officially supposed to be used.  ...and, in fact, the
driver that gets selected in Linux using the rk3288 device tree only
supports the "new" implementation.

Long ago I tried to get a switch to the right IP block landed in the
PWM driver (search for "rk3288: Switch to use the proper PWM IP") but
that got rejected.  In the mean time the grf has grown a full-fledged
driver that already sets other random bits like this.  That means we
can now get the fix landed.

For those wondering how things could have possibly worked for the last
4.5 years, folks have mostly been relying on the bootloader to set
this bit.  ...but occasionally folks have pointed back to my old patch
series [1] in downstream kernels.

[1] https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1391597.htmlSigned-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 57a20248ef3e429dc822f0774bc4e00136c46c83 ]

Experimentally it can be seen that going into deep sleep (specifically
setting PMU_CLR_DMA and PMU_CLR_BUS in RK3288_PMU_PWRMODE_CON1)
appears to fail unless "aclk_dmac1" is on.  The failure is that the
system never signals that it made it into suspend on the GLOBAL_PWROFF
pin and it just hangs.

NOTE that it's confirmed that it's the actual suspend that fails, not
one of the earlier calls to read/write registers.  Specifically if you
comment out the "PMU_GLOBAL_INT_DISABLE" setting in
rk3288_slp_mode_set() and then comment out the "cpu_do_idle()" call in
rockchip_lpmode_enter() then you can exercise the whole suspend path
without any crashing.

This is currently not a problem with suspend upstream because there is
no current way to exercise the deep suspend code.  However, anyone
trying to make it work will run into this issue.

This was not a problem on shipping rk3288-based Chromebooks because
those devices all ran on an old kernel based on 3.14.  On that kernel
"aclk_dmac1" appears to be left on all the time.

There are several ways to skin this problem.

A) We could add "aclk_dmac1" to the list of critical clocks and that
apperas to work, but presumably that wastes power.

B) We could keep a list of "struct clk" objects to enable at suspend
time in clk-rk3288.c and use the standard clock APIs.

C) We could make the rk3288-pmu driver keep a list of clocks to enable
at suspend time.  Presumably this would require a dts and bindings
change.

D) We could just whack the clock on in the existing syscore suspend
function where we whack a bunch of other clocks.  This is particularly
easy because we know for sure that the clock's only parent
("aclk_cpu") is a critical clock so we don't need to do anything more
than ungate it.

In this case I have chosen D) because it seemed like the least work,
but any of the other options would presumably also work fine.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Reviewed-by: NElaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 89e28da82836530f1ac7a3a32fecc31f22d79b3e ]

When building with -Wsometimes-uninitialized, Clang warns:

drivers/soc/mediatek/mtk-pmic-wrap.c:1358:6: error: variable 'rdata' is
used uninitialized whenever '||' condition is true
[-Werror,-Wsometimes-uninitialized]

If pwrap_write returns non-zero, pwrap_read will not be called to
initialize rdata, meaning that we will use some random uninitialized
stack value in our print statement. Zero initialize rdata in case this
happens.

Link: https://github.com/ClangBuiltLinux/linux/issues/401Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Reviewed-by: NNick Desaulniers <ndesaulniers@google.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f316a2b53cd7f37963ae20ec7072eb27a349a4ce ]

hook_fault_code() is an ARM32 specific API for hooking into data abort.

AM65X platforms (that integrate ARM v8 cores and select CONFIG_ARM64 as
arch) rely on pci-keystone.c but on them the enumeration of a
non-present BDF does not trigger a bus error, so the fixup exception
provided by calling hook_fault_code() is not needed and can be guarded
with CONFIG_ARM.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 94d4e7af14a1170e34cf082d92e4c02de9e9fb88 ]

As new transfer mechanisms are added to the EC codebase, they may
not support v2 of the EC protocol.

If the v3 initial handshake transfer fails, the kernel will try
and call cmd_xfer as a fallback. If v2 is not supported, cmd_xfer
will be NULL, and the code will end up causing a kernel panic.

Add a check for NULL before calling the transfer function, along
with a helpful comment explaining how one might end up in this
situation.
Signed-off-by: NEnrico Granata <egranata@chromium.org>
Reviewed-by: NJett Rink <jettrink@chromium.org>
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 3e957b377bf4262aec2dd424f28ece94e36814d4 ]

Added a new local variable in the i40e_setup_tc function named
old_queue_pairs so num_queue_pairs can be restored to the correct
value in case configuring queue channels fails. Additionally, moved
the exit label in the i40e_setup_tc function so the if (need_reset)
block can be executed.
Also, fixed data packing in the i40e_setup_tc function.
Signed-off-by: NAdam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit ea094d53580f40c2124cef3d072b73b2425e7bfd ]

In pcibios_irq_init(), the PCI IRQ routing table 'pirq_table' is first
found through pirq_find_routing_table().  If the table is not found and
CONFIG_PCI_BIOS is defined, the table is then allocated in
pcibios_get_irq_routing_table() using kmalloc().  Later, if the I/O APIC is
used, this table is actually not used.  In that case, the allocated table
is not freed, which is a memory leak.

Free the allocated table if it is not used.
Signed-off-by: NWenwen Wang <wang6495@umn.edu>
[bhelgaas: added Ingo's reviewed-by, since the only change since v1 was to
use the irq_routing_table local variable name he suggested]
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NIngo Molnar <mingo@kernel.org>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9872760eb7b1d4f6066ad8b560714a5d0a728fdb ]

The XDomain protocol messages may start as soon as Thunderbolt control
channel is started. This means that if the other host starts sending
ThunderboltIP packets early enough they will be passed to the network
driver which then gets confused because its resume hook is not called
yet.

Fix this by unregistering the ThunderboltIP protocol handler when
suspending and registering it back on resume.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 083c1b5e50b701899dc32445efa8b153685260d5 ]

When running application tool switchtec-user's `firmware update` and `event
wait` commands concurrently, sometimes the firmware update speed reduced
significantly.

It is because when the MRPC event happened after MRPC event occurrence
check but before the event mask loop reaches its header register in event
ISR, the MRPC event would be masked unintentionally.  Since there's no
chance to enable it again except for a module reload, all the following
MRPC execution completion checks time out.

Fix this bug by skipping the mask operation for MRPC event in event ISR,
same as what we already do for LINK event.

Fixes: 52eabba5 ("switchtec: Add IOCTLs to the Switchtec driver")
Signed-off-by: NWesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NLogan Gunthorpe <logang@deltatee.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 3f54c447df34ff9efac7809a4a80fd3208efc619 ]

Disabling the SMMU when probing from within a kdump kernel so that all
incoming transactions are terminated can prevent the core of the crashed
kernel from being transferred off the machine if all I/O devices are
behind the SMMU.

Instead, continue to probe the SMMU after it is disabled so that we can
reinitialise it entirely and re-attach the DMA masters as they are reset.
Since the kdump kernel may not have drivers for all of the active DMA
masters, we suppress fault reporting to avoid spamming the console and
swamping the IRQ threads.
Reported-by: N"Leizhen (ThunderTown)" <thunder.leizhen@huawei.com>
Tested-by: N"Leizhen (ThunderTown)" <thunder.leizhen@huawei.com>
Tested-by: NBhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 41be3e2618174fdf3361e49e64f2bf530f40c6b0 ]

vfio_dev_present() which is the condition to
wait_event_interruptible_timeout(), will call vfio_group_get_device
and try to acquire the mutex group->device_lock.

wait_event_interruptible_timeout() will set the state of the current
task to TASK_INTERRUPTIBLE, before doing the condition check. This
means that we will try to acquire the mutex while already in a
sleeping state. The scheduler warns us by giving the following
warning:

[ 4050.264464] ------------[ cut here ]------------
[ 4050.264508] do not call blocking ops when !TASK_RUNNING; state=1 set at [<00000000b33c00e2>] prepare_to_wait_event+0x14a/0x188
[ 4050.264529] WARNING: CPU: 12 PID: 35924 at kernel/sched/core.c:6112 __might_sleep+0x76/0x90
....

 4050.264756] Call Trace:
[ 4050.264765] ([<000000000017bbaa>] __might_sleep+0x72/0x90)
[ 4050.264774]  [<0000000000b97edc>] __mutex_lock+0x44/0x8c0
[ 4050.264782]  [<0000000000b9878a>] mutex_lock_nested+0x32/0x40
[ 4050.264793]  [<000003ff800d7abe>] vfio_group_get_device+0x36/0xa8 [vfio]
[ 4050.264803]  [<000003ff800d87c0>] vfio_del_group_dev+0x238/0x378 [vfio]
[ 4050.264813]  [<000003ff8015f67c>] mdev_remove+0x3c/0x68 [mdev]
[ 4050.264825]  [<00000000008e01b0>] device_release_driver_internal+0x168/0x268
[ 4050.264834]  [<00000000008de692>] bus_remove_device+0x162/0x190
[ 4050.264843]  [<00000000008daf42>] device_del+0x1e2/0x368
[ 4050.264851]  [<00000000008db12c>] device_unregister+0x64/0x88
[ 4050.264862]  [<000003ff8015ed84>] mdev_device_remove+0xec/0x130 [mdev]
[ 4050.264872]  [<000003ff8015f074>] remove_store+0x6c/0xa8 [mdev]
[ 4050.264881]  [<000000000046f494>] kernfs_fop_write+0x14c/0x1f8
[ 4050.264890]  [<00000000003c1530>] __vfs_write+0x38/0x1a8
[ 4050.264899]  [<00000000003c187c>] vfs_write+0xb4/0x198
[ 4050.264908]  [<00000000003c1af2>] ksys_write+0x5a/0xb0
[ 4050.264916]  [<0000000000b9e270>] system_call+0xdc/0x2d8
[ 4050.264925] 4 locks held by sh/35924:
[ 4050.264933]  #0: 000000001ef90325 (sb_writers#4){.+.+}, at: vfs_write+0x9e/0x198
[ 4050.264948]  #1: 000000005c1ab0b3 (&of->mutex){+.+.}, at: kernfs_fop_write+0x1cc/0x1f8
[ 4050.264963]  #2: 0000000034831ab8 (kn->count#297){++++}, at: kernfs_remove_self+0x12e/0x150
[ 4050.264979]  #3: 00000000e152484f (&dev->mutex){....}, at: device_release_driver_internal+0x5c/0x268
[ 4050.264993] Last Breaking-Event-Address:
[ 4050.265002]  [<000000000017bbaa>] __might_sleep+0x72/0x90
[ 4050.265010] irq event stamp: 7039
[ 4050.265020] hardirqs last  enabled at (7047): [<00000000001cee7a>] console_unlock+0x6d2/0x740
[ 4050.265029] hardirqs last disabled at (7054): [<00000000001ce87e>] console_unlock+0xd6/0x740
[ 4050.265040] softirqs last  enabled at (6416): [<0000000000b8fe26>] __udelay+0xb6/0x100
[ 4050.265049] softirqs last disabled at (6415): [<0000000000b8fe06>] __udelay+0x96/0x100
[ 4050.265057] ---[ end trace d04a07d39d99a9f9 ]---

Let's fix this as described in the article
https://lwn.net/Articles/628628/.
Signed-off-by: NFarhan Ali <alifm@linux.ibm.com>
[remove now redundant vfio_dev_present()]
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 0ab88ca4bcf18ba21058d8f19220f60afe0d34d8 ]

clang warns that 'contextlen' may be accessed without an initialization:

fs/nfsd/nfs4xdr.c:2911:9: error: variable 'contextlen' is uninitialized when used here [-Werror,-Wuninitialized]
                                                                contextlen);
                                                                ^~~~~~~~~~
fs/nfsd/nfs4xdr.c:2424:16: note: initialize the variable 'contextlen' to silence this warning
        int contextlen;
                      ^
                       = 0

Presumably this cannot happen, as FATTR4_WORD2_SECURITY_LABEL is
set if CONFIG_NFSD_V4_SECURITY_LABEL is enabled.
Adding another #ifdef like the other two in this function
avoids the warning.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 0b8f62625dc309651d0efcb6a6247c933acd8b45 ]

A fuzzer recently triggered lockdep warnings about potential sb_writers
deadlocks caused by fh_want_write().

Looks like we aren't careful to pair each fh_want_write() with an
fh_drop_write().

It's not normally a problem since fh_put() will call fh_drop_write() for
us.  And was OK for NFSv3 where we'd do one operation that might call
fh_want_write(), and then put the filehandle.

But an NFSv4 protocol fuzzer can do weird things like call unlink twice
in a compound, and then we get into trouble.

I'm a little worried about this approach of just leaving everything to
fh_put().  But I think there are probably a lot of
fh_want_write()/fh_drop_write() imbalances so for now I think we need it
to be more forgiving.
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>