When trying to understand semop code, I found a small mistake in the check
for semadj (undo) value overflow.  The new undo value is not stored
immediately and next potential checks are done against the old value.

The failing scenario is not much practical.  One semop call has to do more
operations on the same semaphore.  Also semval and semadj must have
different values, so there has to be some operations without SEM_UNDO
flag.  For example:

	struct sembuf depositor_op[1];
	struct sembuf collector_op[2];

	depositor_op[0].sem_num = 0;
	depositor_op[0].sem_op = 20000;
	depositor_op[0].sem_flg = 0;

	collector_op[0].sem_num = 0;
	collector_op[0].sem_op = -10000;
	collector_op[0].sem_flg = SEM_UNDO;
	collector_op[1].sem_num = 0;
	collector_op[1].sem_op = -10000;
	collector_op[1].sem_flg = SEM_UNDO;

	if (semop(semid, depositor_op, 1) == -1)
		{ perror("Failed to do 1st deposit"); return 1; }

	if (semop(semid, collector_op, 2) == -1)
		{ perror("Failed to do 1st collect"); return 1; }

	if (semop(semid, depositor_op, 1) == -1)
		{ perror("Failed to do 2nd deposit"); return 1; }

	if (semop(semid, collector_op, 2) == -1)
		{ perror("Failed to do 2nd collect"); return 1; }

	return 0;

It passes without error now but the semadj value has overflown in the 2nd
collector operation.

[akpm@linux-foundation.org: restore lessened scope of local `undo']
[davidlohr@hp.com: correct header comment for perform_atomic_semop]
Signed-off-by: NPetr Mladek <pmladek@suse.cz>
Acked-by: NDavidlohr Bueso <davidlohr@hp.com>
Acked-by: NManfred Spraul <manfred@colorfullife.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: NDavidlohr Bueso <davidlohr@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

mca_init() no longer exists.
sbus_init() is defined in arch/sparc/kernel/sbus.c and is a subsys_initcall.
both are not needed in main.c any more.
Signed-off-by: NKang Hu <hukangustc@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAndrey Ryabinin <a.ryabinin@samsung.com>
Cc: Jason Baron <jbaron@akamai.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes following scenario:

  $ echo 'file dynamic_debug.c line 1-123 +p' > /sys/kernel/debug/dynamic_debug/control
  -bash: echo: write error: Invalid argument
  $ dmesg | grep dynamic_debug
  dynamic_debug:ddebug_parse_query: last-line:123 < 1st-line:1
  dynamic_debug:ddebug_parse_query: query parse failed
Signed-off-by: NAndrey Ryabinin <a.ryabinin@samsung.com>
Cc: Jason Baron <jbaron@akamai.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

parse_lineno() returns either negative error code or zero.  We don't
need to print something here because if parse_lineno fails it will print
error message.
Signed-off-by: NAndrey Ryabinin <a.ryabinin@samsung.com>
Cc: Jason Baron <jbaron@akamai.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Suppress log message like this: (open_delete,8328,0):ocfs2_unlink:951
ERROR: status = -2

Orabug:17445485
Signed-off-by: NXiaowei Hu <xiaowei.hu@oracle.com>
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit da29bd36 ("mm/mm_init.c: make creation of the mm_kobj happen
earlier than device_initcall") changed to pure_initcall(mm_sysfs_init).

That's too early: mm_sysfs_init() depends on core_initcall(ksysfs_init)
to have made the kernel_kobj directory "kernel" in which to create "mm".

Make it postcore_initcall(mm_sysfs_init).  We could use core_initcall(),
and depend upon Makefile link order kernel/ mm/ fs/ ipc/ security/ ...
as core_initcall(debugfs_init) and core_initcall(securityfs_init) do;
but better not.
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It is based on uninitialized value keep_early.  This leads to
unpredictable result.

[akpm@linux-foundation.org: simplify code]
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Revert commit ece86e22, which was intended as a small performance
improvement.

Despite the claim that the patch doesn't introduce any functional
changes in fact it does.

The "no page" path behaves different now.  Originally, vmalloc_to_page
might return NULL under some conditions, with new implementation it
returns pfn_to_page(0) which is not the same as NULL.

Simple test shows the difference.

test.c

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/vmalloc.h>
#include <linux/mm.h>

int __init myi(void)
{
	struct page *p;
	void *v;

	v = vmalloc(PAGE_SIZE);
	/* trigger the "no page" path in vmalloc_to_page*/
	vfree(v);

	p = vmalloc_to_page(v);

	pr_err("expected val = NULL, returned val = %p", p);

	return -EBUSY;
}

void __exit mye(void)
{

}
module_init(myi)
module_exit(mye)

Before interchange:
expected val = NULL, returned val =   (null)

After interchange:
expected val = NULL, returned val = c7ebe000
Signed-off-by: NVladimir Murzin <murzin.v@gmail.com>
Cc: Jianyu Zhan <nasa4836@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In original __alloc_memory_core_early() for bootmem wrapper, we do not
align size silently.

We should not do that, as later free with old size will leave some range
not freed.

It's obvious that code is copied from memblock_base_nid(), and that code
is wrong for the same reason.

Also remove that in memblock_alloc_base.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Dave reported big numa system booting is broken.

It turns out that commit 5b6e5295 ("x86: memblock: set current limit
to max low memory address") sets the limit to low wrongly.

max_low_pfn_mapped is different from max_pfn_mapped.
max_low_pfn_mapped is always under 4G.

That will memblock_alloc_nid all go under 4G.

Revert 5b6e5295 to fix a no-boot regression which was triggered by
457ff1de ("lib/swiotlb.c: use memblock apis for early memory
allocations").
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Reported-by: NDave Hansen <dave.hansen@intel.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The new memblock_virt APIs are used to replaced old bootmem API.

We need to allocate page below 4G for swiotlb.

That should fix regression on Andrew's system that is using swiotlb.
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull tracing fixes from Steven Rostedt:
 "The first two patches fix the debugfs README file to reflect better
  the new features added to 3.14.

  The third patch is a minor bugfix to the trace_puts() functions that
  will crash the system if a developer adds one before the tracing
  system is setup.  It also affects trace_printk() if it has no
  arguments, as the code will convert it to a trace_puts() as well.

  Note, this bug will not affect unmodified kernels, as trace_printk()
  and trace_puts() should only be used by developers for testing"

* tag 'trace-fixes-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Check if tracing is enabled in trace_puts()
  tracing: Fix formatting of trace README file
  tracing/README: Add event file usage to tracing mini-HOWTO

Merge tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb

Pull swiotlb bug-fixes from Konrad Rzeszutek Wilk:
 - Don't DoS with 'swiotlb is full' message.
 - Documentation update.

* tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
  swiotlb: Don't DoS us with 'swiotlb buffer is full' (v2)
  swiotlb: update format

Merge tag 'pwm/for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm changes from Thierry Reding:
 "The patches for this release cycle include various enhancements
  (device tree support, better compile coverage, ...) for existing
  drivers.  There is a new driver for Atmel SoCs.

  Various drivers as well as the sysfs support received minor fixes and
  cleanups"

* tag 'pwm/for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: tiecap: Remove duplicate put_sync call
  pwm: tiehrpwm: use dev_err() instead of pr_err()
  pwm: pxa: remove unnecessary space before tabs
  pwm: ep93xx: split module author names
  pwm: use seq_puts() instead of seq_printf()
  pwm: atmel-pwm: Do not unprepare clock after successful registration
  of: Add Atmel PWM controller device tree binding
  pwm: atmel-pwm: Add Atmel PWM controller driver
  backlight: pwm_bl: Remove error message upon devm_kzalloc() failure
  pwm: pca9685: depends on I2C rather than REGMAP_I2C
  pwm: renesas-tpu: Enable driver compilation with COMPILE_TEST
  pwm: jz4740: Use devm_clk_get()
  pwm: jz4740: Pass device to clk_get()
  pwm: sysfs: Convert to use ATTRIBUTE_GROUPS macro
  pwm: pxa: Add device tree support

Pull firewire updates from Stefan Richter:
 "IEEE 1394 (FireWire) subsystem changes:

   - make remote debugging over 1394 a runtime option instead of a
     buildtime option
   - extend remote debug access past the 4 GB barrier on respectively
     capable hardware
   - documentation update"

* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
  firewire: Enable remote DMA above 4 GB
  firewire: ohci: Turn remote DMA support into a module parameter
  Documentation/: update FireWire debugging documentation

Pull cris changes from Jesper Nilsson:
 "Mostly removal of deprecated or old code, but also a long promised
  update of the CRIS syscalls"

* tag 'cris-for-3.14' of git://jni.nu/cris:
  Drop code for CRISv10 CPU simulator
  Cleanup whitespace, remove old author tag
  CRIS: Add missing syscalls
  cris: sync_serial: remove interruptible_sleep_on
  cris: remove deprecated IRQF_DISABLED

Pull UML changes from Richard Weinberger:
 "This time only various cleanups and housekeeping patches"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: hostfs: make functions static
  um: Include generic barrier.h
  um: Removed unused attributes from thread_struct

Pull MMC updates from Chris Ball:
 "MMC highlights for 3.14:

  Core:
   - Avoid get_cd() on cards marked nonremovable

  Drivers:
   - arasan: New driver for controllers found in e.g. Xilinx Zynq SoC
   - dwmmc: Support Hisilicon K3 SoC controllers
   - esdhc-imx: Support for HS200 mode, DDR modes on MX6, runtime PM
   - sdhci-pci: Support O2Micro/BayHubTech controllers used in laptops
     like Lenovo ThinkPad W540, Dell Latitude E5440, Dell Latitude E6540
   - tegra: Support Tegra124 SoCs"

* tag 'mmc-updates-for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (55 commits)
  mmc: sdhci-pci: Fix possibility of chip->fixes being null
  mmc: sdhci-pci: Fix BYT sd card getting stuck in runtime suspend
  mmc: sdhci: Allow for long command timeouts
  mmc: sdio: add a quirk for broken SDIO_CCCR_INTx polling
  mmc: sdhci: fix lockdep error in tuning routine
  mmc: dw_mmc: k3: remove clk_table
  mmc: dw_mmc: fix dw_mci_get_cd
  mmc: dw_mmc: fix sparse non static symbol warning
  mmc: sdhci-esdhc-imx: fix warning during module remove function
  mmc: sdhci-esdhc-imx: fix access hardirq-unsafe lock in atomic context
  mmc: core: sd: implement proper support for sd3.0 au sizes
  mmc: atmel-mci: add vmmc-supply support
  mmc: sdhci-pci: add broken HS200 quirk for Intel Merrifield
  mmc: sdhci: add quirk for broken HS200 support
  mmc: arasan: Add driver for Arasan SDHCI
  mmc: dw_mmc: add dw_mmc-k3 for k3 platform
  mmc: dw_mmc: use slot-gpio to handle cd pin
  mmc: sdhci-pci: add support of O2Micro/BayHubTech SD hosts
  mmc: sdhci-pci: break out definitions to header file
  mmc: tmio: fixup compile error
  ...

Conflicts:
	MAINTAINERS

Pull 9p changes from Eric Van Hensbergen:
 "Included are a new cache model for support of mmap, and several
  cleanups across the filesystem and networking portions of the code"

* tag 'for-3.14-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: update documentation
  9P: introduction of a new cache=mmap model.
  net/9p: remove virtio default hack and set appropriate bits instead
  9p: remove useless 'name' variable and assignment
  9p: fix return value in case in v9fs_fid_xattr_set()
  9p: remove useless variable and assignment
  9p: remove useless assignment
  9p: remove unused 'super_block' struct pointer
  9p: remove never used return variable
  9p: remove unused 'p9_fid' struct pointer
  9p: remove unused 'p9_client' struct pointer

The hostfs_*() callback functions are all only used within
hostfs_kern.c, so make them static.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: user-mode-linux-devel@lists.sourceforge.net
Signed-off-by: NRichard Weinberger <richard@nod.at>

...to get smp_store_release().
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NRichard Weinberger <richard@nod.at>

temp_stack and mm_count have no users and can be killed.
Signed-off-by: NRichard Weinberger <richard@nod.at>

Merge ipmi fixes from Corey Minyard:
 "Just some collected fixes for 3.14.  Nothing huge"

* emailed patches from Corey Minyard <minyard@acm.org>:
  ipmi: Cleanup error return
  ipmi: fix timeout calculation when bmc is disconnected
  ipmi: use USEC_PER_SEC instead of 1000000 for more meaningful
  ipmi: remove deprecated IRQF_DISABLED

Return proper errors for a lot of IPMI failure cases.  Also call
pci_disable_device when IPMI PCI devices are removed.
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Loading ipmi_si module while bmc is disconnected, we found the timeout
is longer than 5 secs.  Actually it takes about 3 mins and 20
secs.(HZ=250)

error message as below:
  Dec 12 19:08:59 linux kernel: IPMI BT: timeout in RD_WAIT [ ] 1 retries left
  Dec 12 19:08:59 linux kernel: BT: write 4 bytes seq=0x01 03 18 00 01
  [...]
  Dec 12 19:12:19 linux kernel: IPMI BT: timeout in RD_WAIT [ ]
  Dec 12 19:12:19 linux kernel: failed 2 retries, sending error response
  Dec 12 19:12:19 linux kernel: IPMI: BT reset (takes 5 secs)
  Dec 12 19:12:19 linux kernel: IPMI BT: flag reset [ ]

Function wait_for_msg_done() use schedule_timeout_uninterruptible(1) to
sleep 1 tick, so we should subtract jiffies_to_usecs(1) instead of 100
usecs from timeout.
Reported-by: NHu Shiyuan <hushiyuan@huawei.com>
Signed-off-by: NXie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use USEC_PER_SEC instead of 1000000, that making the later bugfix
more clearly.
Signed-off-by: NXie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull spi updates from Mark Brown:
 "A respun version of the merges for the pull request previously sent
  with a few additional fixes.  The last two merges were fixed up by
  hand since the branches have moved on and currently have the prior
  merge in them.

  Quite a busy release for the SPI subsystem, mostly in cleanups big and
  small scattered through the stack rather than anything else:

   - New driver for the Broadcom BC63xx HSSPI controller
   - Fix duplicate device registration for ACPI
   - Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
     changes upon which the transiton depends)
   - Some small optimisations to reduce the amount of time we hold locks
     in the datapath, eliminate some redundant checks and the size of a
     spi_transfer
   - Lots of fixes, cleanups and general enhancements to drivers,
     especially the rspi and Atmel drivers"

* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
  spi: core: Fix transfer failure when master->transfer_one returns positive value
  spi: Correct set_cs() documentation
  spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
  spi: Spelling s/finised/finished/
  spi: sc18is602: Convert to use bits_per_word_mask
  spi: Remove duplicate code to set default bits_per_word setting
  spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
  spi: clps711x: Add MODULE_ALIAS to support module auto-loading
  spi: rspi: Add missing clk_disable() calls in error and cleanup paths
  spi: rspi: Spelling s/transmition/transmission/
  spi: rspi: Add support for specifying CPHA/CPOL
  spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
  spi: rspi: Add more QSPI register documentation
  spi: rspi: Add more RSPI register documentation
  spi: rspi: Remove dependency on DMAE for SHMOBILE
  spi/s3c64xx: Correct indentation
  spi: sh: Use spi_sh_clear_bit() instead of open-coded
  spi: bitbang: Grammar s/make to make/to make/
  spi: sh-hspi: Spelling s/recive/receive/
  spi: core: Improve tx/rx_nbits check comments
  ...

Pull regulator updates from Mark Brown:
 "A respin of the merges in the previous pull request with one extra
  fix.

  A quiet release for the regulator API, quite a large number of small
  improvements all over but other than the addition of new drivers for
  the AS3722 and MAX14577 there is nothing of substantial non-local
  impact"

* tag 'regulator-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (47 commits)
  regulator: pfuze100-regulator: Improve dev_info() message
  regulator: pfuze100-regulator: Fix some checkpatch complaints
  regulator: twl: Fix checkpatch issue
  regulator: core: Fix checkpatch issue
  regulator: anatop-regulator: Remove unneeded memset()
  regulator: s5m8767: Update LDO index in s5m8767-regulator.txt
  regulator: as3722: set enable time for SD0/1/6
  regulator: as3722: detect SD0 low-voltage mode
  regulator: tps62360: Fix up a pointer-integer size mismatch warning
  regulator: anatop-regulator: Remove unneeded kstrdup()
  regulator: act8865: Fix build error when !OF
  regulator: act8865: register all regulators regardless of how many are used
  regulator: wm831x-dcdc: Remove unneeded 'err' label
  regulator: anatop-regulator: Add MODULE_ALIAS()
  regulator: act8865: fix incorrect devm_kzalloc for act8865
  regulator: act8865: Remove set_suspend_[en|dis]able implementation
  regulator: act8865: Remove unneeded regulator_unregister() calls
  regulator: s2mps11: Clean up redundant code
  regulator: tps65910: Simplify setting enable_mask for regulators
  regulator: act8865: add device tree binding doc
  ...

Pull regmap updates from Mark Brown:
 "Nothing terribly exciting with regmap this release, mainly a few small
  extensions to allow more devices to be supported:

   - Allow the bulk I/O APIs to be used with no-bus regmaps
   - Support interrupt controllers with zero ack base
   - Warning and spelling fixes"

* tag 'regmap-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: fix a couple of typos
  regmap: Allow regmap_bulk_write() to work for "no-bus" regmaps
  regmap: Allow regmap_bulk_read() to work for "no-bus" regmaps
  regmap: irq: Allow using zero value for ack_base
  regmap: Fix 'ret' would return an uninitialized value

Pull networking updates from David Miller:

 1) BPF debugger and asm tool by Daniel Borkmann.

 2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.

 3) Correct reciprocal_divide and update users, from Hannes Frederic
    Sowa and Daniel Borkmann.

 4) Currently we only have a "set" operation for the hw timestamp socket
    ioctl, add a "get" operation to match.  From Ben Hutchings.

 5) Add better trace events for debugging driver datapath problems, also
    from Ben Hutchings.

 6) Implement auto corking in TCP, from Eric Dumazet.  Basically, if we
    have a small send and a previous packet is already in the qdisc or
    device queue, defer until TX completion or we get more data.

 7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.

 8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
    Borkmann.

 9) Share IP header compression code between Bluetooth and IEEE802154
    layers, from Jukka Rissanen.

10) Fix ipv6 router reachability probing, from Jiri Benc.

11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.

12) Support tunneling in GRO layer, from Jerry Chu.

13) Allow bonding to be configured fully using netlink, from Scott
    Feldman.

14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
    already get the TCI.  From Atzm Watanabe.

15) New "Heavy Hitter" qdisc, from Terry Lam.

16) Significantly improve the IPSEC support in pktgen, from Fan Du.

17) Allow ipv4 tunnels to cache routes, just like sockets.  From Tom
    Herbert.

18) Add Proportional Integral Enhanced packet scheduler, from Vijay
    Subramanian.

19) Allow openvswitch to mmap'd netlink, from Thomas Graf.

20) Key TCP metrics blobs also by source address, not just destination
    address.  From Christoph Paasch.

21) Support 10G in generic phylib.  From Andy Fleming.

22) Try to short-circuit GRO flow compares using device provided RX
    hash, if provided.  From Tom Herbert.

The wireless and netfilter folks have been busy little bees too.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
  net/cxgb4: Fix referencing freed adapter
  ipv6: reallocate addrconf router for ipv6 address when lo device up
  fib_frontend: fix possible NULL pointer dereference
  rtnetlink: remove IFLA_BOND_SLAVE definition
  rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
  qlcnic: update version to 5.3.55
  qlcnic: Enhance logic to calculate msix vectors.
  qlcnic: Refactor interrupt coalescing code for all adapters.
  qlcnic: Update poll controller code path
  qlcnic: Interrupt code cleanup
  qlcnic: Enhance Tx timeout debugging.
  qlcnic: Use bool for rx_mac_learn.
  bonding: fix u64 division
  rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
  sfc: Use the correct maximum TX DMA ring size for SFC9100
  Add Shradha Shah as the sfc driver maintainer.
  net/vxlan: Share RX skb de-marking and checksum checks with ovs
  tulip: cleanup by using ARRAY_SIZE()
  ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
  net/cxgb4: Don't retrieve stats during recovery
  ...

Pull perf fixes from Ingo Molnar:
 "A handful of tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf symbols: Load map before using map->map_ip()
  perf tools: Fix traceevent plugin path definitions
  perf symbols: Fix JIT symbol resolution on heap
  perf stat: Fix memory corruption of xyarray when cpumask is used
  perf evsel: Remove duplicate member zeroing after free
  perf tools: Ensure sscanf does not overrun the "mem" field
  perf stat: fix NULL pointer reference bug with event unit
  perf tools: Add support for the xtensa architecture
  perf session: Free cpu_map in perf_session__cpu_bitmap
  perf timechart: Fix wrong SVG height

Pull scheduler fixes from Ingo Molnar:
 "A couple of regression fixes mostly hitting virtualized setups, but
  also some bare metal systems"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/x86/tsc: Initialize multiplier to 0
  sched/clock: Fixup early initialization
  sched/preempt/x86: Fix voluntary preempt for x86
  Revert "sched: Fix sleep time double accounting in enqueue entity"

Pull user namespaces work from Eric Biederman:
 "The work to convert the kernel to use kuid_t and kgid_t has been
  finished since 3.12 so it is time to remove the scaffolding that
  allowed the work to progress incrementally.

  The first patch on this branch just removes the scaffolding, ensuring
  we will always get compile errors if people accidentally try the
  userspace and the kernel uid and gid types.  The second patch an
  overlooked and unused chunk of mips code that that fails to build
  after the first patch.

  The code hasn't been in linux-next for long (as I was out of it and
  could not sheppared the cold properly) but the patch has been around
  for a long time just waiting for the day when I had finished the
  uid/gid conversions.  Putting the code in linux-next did find the
  compile failure on mips so I took the time to get that fix reviewed
  and included.  Beyond that I am not too worried about errors because
  all these two patches do is delete a modest amount of code"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  MIPS: VPE: Remove vpe_getuid and vpe_getgid
  userns:  userns: Remove UIDGID_STRICT_TYPE_CHECKS

Pull ARC changes from Vineet Gupta:
 - IPI optimization and cleanups
 - Support for bootloader provided external Device Tree blobs

* tag 'arc-v3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [cmdline] support External Device Trees from u-boot
  ARC: [cmdline] uboot cmdline handling rework
  ARC: [SMP] optimize IPI send and receive
  ARC: [SMP] simplify IPI code
  ARC: [SMP] cpu halt interface doesn't need "self" cpu-id
  ARC: [SMP] IPI ACK interface doesn't need "self" cpu-id
  ARC: [SMP] cpumask not needed in IPI send path

Pull Xtensa patches from Chris Zankel:
 "The major changes are adding support for SMP for Xtensa, fixing and
  cleaning up the ISS (simulator) network driver, and better support for
  device trees"

* tag 'xtensa-next-20140123' of git://github.com/czankel/xtensa-linux: (40 commits)
  xtensa: implement ndelay
  xtensa: clean up udelay
  xtensa: enable HAVE_PERF_EVENTS
  xtensa: remap io area defined in device tree
  xtensa: support default device tree buses
  xtensa: initialize device tree clock sources
  xtensa: xtfpga: fix definitions of platform devices
  xtensa: standardize devicetree cpu compatible strings
  xtensa: avoid duplicate of IO range definitions
  xtensa: fix ATOMCTL register documentation
  xtensa: Enable irqs after cpu is set online
  xtensa: ISS: raise network polling rate to 10 times/sec
  xtensa: remove unused XTENSA_ISS_NETWORK Kconfig parameter
  xtensa: ISS: avoid simple_strtoul usage
  xtensa: Switch to sched_clock_register()
  xtensa: implement CPU hotplug
  xtensa: add SMP support
  xtensa: add MX irqchip
  xtensa: clear timer IRQ unconditionally in its handler
  xtensa: clean up do_interrupt/do_IRQ
  ...

Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Pull perf/urgent fixes from Arnaldo Carvalho de Melo:

  * Fix traceevent plugin path definitions (Josh Boyer)

  * Load map before using map->map_ip() (Masami Hiramatsu)
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Pull vfio update from Alex Williamson:
 - convert to misc driver to support module auto loading
 - remove unnecessary and dangerous use of device_lock

* tag 'vfio-v3.14-rc1' of git://github.com/awilliam/linux-vfio:
  vfio-pci: Don't use device_lock around AER interrupt setup
  vfio: Convert control interface to misc driver
  misc: Reserve minor for VFIO

Pull md updates from Neil Brown:
 "All bug fixes, two tagged for -stable"

* tag 'md/3.14' of git://neil.brown.name/md:
  md/raid5: close recently introduced race in stripe_head management.
  md/raid5: fix long-standing problem with bitmap handling on write failure.
  md: check command validity early in md_ioctl().
  md: ensure metadata is writen after raid level change.
  md/raid10: avoid fullsync when not necessary.
  md: allow a partially recovered device to be hot-added to an array.
  md: Change handling of save_raid_disk and metadata update during recovery.