When KDUMP is triggered the driver first talks to the firmware in INTX
mode, but the adapter firmware is still in MSIX mode. Therefore the first
driver command hangs since the driver is waiting for an INTX response and
firmware gives a MSIX response. If when the OS is installed on a RAID
drive created by the adapter KDUMP will hang since the driver does not
receive a response in sync mode.

Fixed by: Change the firmware to INTX mode if it is in MSIX mode before
sending the first sync command.

Cc: stable@vger.kernel.org
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently driver completes double completed or spurious interrupted fibs.
This  is not necessary and causes the SCSI mid layer to issue aborts and
resets, since completing a fib  prematurely might trigger a race condition
resulting in the driver not calling the scsi_done callback.

Fixed by removing the call to fib complete.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Firmware AIF messages about cache loss and data recovery are being missed
by the driver since currently they are not captured but rather let go.
This patch to capture those messages and log them for the user.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.

In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.

The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.

Fixed by: Adding another kthread_should_stop() before schedule_timeout()
Cc: stable@vger.kernel.org
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

As the firmware for series 6, 7, 8 cards does not support msi, remove it
in the driver
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

aac_fib_send has a special function case for initial commands during
driver initialization using wait < 0(pseudo sync mode). In this case,
the command does not sleep but rather spins checking for timeout.This
loop is calls cpu_relax() in an attempt to allow other processes/threads
to use the CPU, but this function does not relinquish the CPU and so the
command will hog the processor. This was observed in a KDUMP
"crashkernel" and that prevented the "command thread" (which is
responsible for completing the command from being timed out) from
starting because it could not get the CPU.

Fixed by replacing "cpu_relax()" call with "schedule()"
Cc: stable@vger.kernel.org
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The adapter has to be started after updating the number of MSIX Vectors

Fixes: ecc479e0 (aacraid: Set correct MSIX count for EEH recovery)
Cc: stable@vger.kernel.org
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Suggested-by: NSeymour, Shane M <shane.seymour@hpe.com>
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Current driver checks for NULL return from aac_fib_alloc_tag, but it not
possible for it to return NULL.

Fixed by: Remove all the checks for NULL returns from aac_fib_alloc_tag
Suggested-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

mptsas_smp_handler() checks for dma mapping errors by comparison
returned address with zero, while pci_dma_mapping_error() should be
used.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: NSathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The file atari_NCR5380.c has been removed from the tree so remove it
from the MAINTAINERS file as well.

While we are here, add the file dtc3x80.txt as it is only relevant to
the dtc driver.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Some drives set the ILI flag together with MEDIUM ERROR sense code.
Clear the ILI flag in this case so that the medium error will be
handled.  The problem was reported by Maurizio Lombardi.
Signed-off-by: NKai Mäkisara <kai.makisara@kolumbus.fi>
Reviewed-by: NLaurence Oberman <loberman@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove incorrect lockdep assertion from lpfc_sli_hbqbuf_find() which
acquires the hbalock itself. Fix the comment which resulted in this
mistake.

Fixes: 1c2ba475 ("lpfc: Add lockdep assertions")
Signed-off-by: NSebastian Herbszt <herbszt@gmx.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Presumably it isn't possible to have empty lists here, but my static
checker doesn't know that and complains that "ep" can be used
uninitialized.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NNilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This has only called from show_sas_rphy_enclosure_identifier().  The
caller expects that we set an identifier, otherwise it uses an
uninitialized variable.

[mkp: fixed typo]
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Firmware events are queued up using the fw_event_work's struct work, not
its delayed_work member.  The initial driver for SAS2 controllers had
handled firmware reset using the rescan barrier and was later redesigned
through "mpt2sas: [Resend] Host Reset code cleanup".  The delayed_work
variables are now unused and may provoke CONFIG_DEBUG_OBJECTS_TIMERS
"assert_init not available" false warnings in
_scsih_fw_event_cleanup_queue.

Cleanup fw_event_work's unused entries, update its kerneldoc, and
update _scsih_fw_event_cleanup_queue accordingly.

Fixes: 146b16c8 (mpt3sas: Refcount fw_events and fix unsafe list usage)
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add custom version of function to allocate device,
alloc_dev_quirk_v2_hw().  For sata devices the device id bit0 should be
0.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add v2 hw custom function slot_index_alloc_quirk_v2_hw().  SAS devices
should have IPTT bit0 equal to 1.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add methods to use HW specific versions of functions to allocate slot
and device.  HW specific methods are permitted to workaround device id
vs IPTT collision issue in v2 hw.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch will do code optmization for task management functions.
Below are key changes:

1. Remove reset_device hook as it was not being used and driver was
setting this to NULL.

2. Create wrapper functions for task abort and target reset and inside
   these functions adapter specific calls be made. e.g. fusion adapters
   support task abort and target reset so task abort and target reset
   should be issued to fusion adapters only and for MFI adapters, print
   a message saying feature not supported.
Signed-off-by: NSumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In OCR path, before calling chip reset calls function
megasas_wait_for_outstanding_fusion to check reason for OCR. In case of
firmware FAULT initiated OCR and DCMD timeout initiated timeout, driver
will clear any outstanding reply (yet to be processed by driver) in
reply queues before going for chip reset. This code is added to handle a
scenario when IO timeout initiated adapter reset and management
application initiated adapter reset (by sending command to FAULT
firmware) happens simultaneously since adapter reset function is
safe-guarded by reset_mutex so only thread will be doing controller
reset. Consider IO timeout thread gets mutex and proceeds with adapter
reset process after disabling interrupts and by the time management
application has fired command to firmware to do adapter reset and the
same command is completed by firmware but since interrupts are disabled,
driver will not get completion and the same command will be in
outstanding/pending commands list of driver and refires same command
from IO timeout thread after chip reset which will again FAULT firmware
and eventually causes kill adapter.
Signed-off-by: NSumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch will reduce memory footprints of megaraid_sas driver when
booted in kdump mode.  Driver will not allocate memory for optional and
perfromance oriented features.  Below are key changes done in
megaraid_sas driver to do this:

1. Limit Controller's queue depth to 100 in kdump mode.

2. Do not allocate memory for system info buffer and PD info buffer.

3. Disable performance oriented features e.g. Disable RDPQ mode, disable
   dual queue depth, restrict to single MSI-x vector.
Signed-off-by: NSumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch avoids that building with W=1 causes gcc to report the
following type of warning:

    no previous prototype for ... [-Wmissing-prototypes]
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ewan Milne <emilne@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

'struct timeval' will have its tv_sec value overflow on 32-bit systems
in year 2038 and beyond. This patch replaces the use of struct timeval
for computing mpi_request.TimeStamp, and instead uses ktime_t which
provides 64-bit seconds value. The timestamp computed remains
unaffected (milliseconds since Unix epoch).
Signed-off-by: NTina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

It is unclear what the original intent of the masking was, but it is
clearly incorrect to truncate a physical address before calling
ioremap().  On systems where there are valid physical address bits above
bit-31 (arm64 for example) the result is an eventual OOPs when
initializing the driver.

Remove the bogus code to fix it.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Acked-by: NJack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

struct register_host_info stores a 64-bit UTC system time timestamp.
This patch removes the use of 'struct timeval' to obtain that timestamp
as its tv_sec value will overflow on 32-bit systems in year 2038 beyond.
The patch uses ktime_get_real_seconds() which returns a 64-bit seconds value.
Signed-off-by: NTina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch fixes the ITCT table setup as it should be configured
differently for SAS and SATA devices.  For SATA disks there is no need
to set qw2 (already zeroed).  Also, link parameters for Bus inactive
limit, max connection time limit, and reject to open limit timers
parameters are changed to match global config register,
MAX_CON_TIME_LIMIT_TIME, as recommended by hw team.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds support for directly attaching SATA disks to phy
4-8. The problem was that only registers concerned with phy 0-3 were
being considered in sata_int_v2_hw().  The issue was not detected
previously as the development board only exposed phy 0-3; the new board
provides access to 8 phys.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Intermittently it is found that when multiple SATA disks are directly
connected to the host that some disks are not detected.  The problem is
that all set bitfields in ENT_INT_SRC1 are cleared for all phys in
sata_int_v2_hw() - it should clear the set bit for the phy being
serviced.

Also unnecessary double-write to ENT_INT_SRC1 and ENT_INT_SRC_MSK1 is
removed (remaining writes are done at end label).
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Contrary to the field name, the MCR (max connection rate) in the ITCT
should hold the device linkrate (linkrate of the connected phy), and not
the max linkrate.

This fixes an issue seen where some SATA drives connected through an
expander which would not attach.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Now it's ready to move the mempool based SG chained allocator code from
SCSI driver to lib/sg_pool.c, which will be compiled only based on a Kconfig
symbol CONFIG_SG_POOL.

SCSI selects CONFIG_SG_POOL.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMing Lin <ming.l@ssi.samsung.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.

Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.

Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: NMing Lin <ming.l@ssi.samsung.com>
Acked-by: NTejun Heo <tj@kernel.org>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Rename SCSI specific struct and functions to more genenic names.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMing Lin <ming.l@ssi.samsung.com>
Reviewed-by: NSagi Grimberg <sgi@grimberg.me>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Parameter "bool mq" is block driver specific.
Change it to "first_chunk" to make it more generic.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMing Lin <ming.l@ssi.samsung.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replace parameter "struct scsi_data_buffer" with "struct sg_table" in
SG alloc/free functions to make them generic.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMing Lin <ming.l@ssi.samsung.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

zfcp has its own mechanism for selective scanning, so revert to the
original scanning behaviour to not confuse users.

Fixes: 4e91e876e9b8b6eb4255aa0d690778a89d3f1d28
Suggested-by: NBenjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NBenjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Claim Marvell 9485 controllers regardless of subdevice ID.

Tested on ASUS P9A-I/C2550/SAS/4L which uses vendor-specific 1043:8635.

[mkp: Tweaked commit message]
Signed-off-by: NLeonid Moiseichuk <leonid.moiseichuk@gmail.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>