Fix the build warning about variable 'last_freed_endpoint'
set but not used [-Wunused-but-set-variable]
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

At present, TCPM code assumes that local device supports
variable/batt pdos and always selects the pdo with highest
possible power within the board limit. This assumption
might not hold good for all devices. To overcome this,
this patch makes TCPM only accept a source_pdo when there is
a matching sink pdo.

For Fixed pdos: The voltage should match between the
incoming source_cap and the registered snk_pdo
For Variable/Batt pdos: The incoming source_cap voltage
range should fall within the registered snk_pdo's voltage
range.

Also, when the cap_mismatch bit is set, the max_power/current
should be set to the max_current/power of the sink_pdo.
This is according to:

"If the Capability Mismatch bit is set to one
The Maximum Operating Current/Power field may contain a value
larger than the maximum current/power offered in the Source
Capabilities message’s PDO as referenced by the Object position field.
This enables the Sink to indicate that it requires more current/power
than is being offered. If the Sink requires a different voltage this
will be indicated by its Sink Capabilities message.
Signed-off-by: NBadhri Jagan Sridharan <Badhri@google.com>
Acked-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The source and sink caps should follow the following rules.
This patch validates whether the src_caps/snk_caps adheres
to it.

6.4.1 Capabilities Message
A Capabilities message (Source Capabilities message or Sink
Capabilities message) shall have at least one Power
Data Object for vSafe5V. The Capabilities message shall also
contain the sending Port’s information followed by up to
6 additional Power Data Objects. Power Data Objects in a
Capabilities message shall be sent in the following order:

1. The vSafe5V Fixed Supply Object shall always be the first object.
2. The remaining Fixed Supply Objects, if present, shall be sent
   in voltage order; lowest to highest.
3. The Battery Supply Objects, if present shall be sent in Minimum
   Voltage order; lowest to highest.
4. The Variable Supply (non-battery) Objects, if present, shall be
   sent in Minimum Voltage order; lowest to highest.

Errors in source/sink_caps of the local port will prevent
the port registration. Whereas, errors in source caps of partner
device would only log them.
Signed-off-by: NBadhri Jagan Sridharan <Badhri@google.com>
Acked-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This corrects the endpiont type value set to the DbC bulk in endpoint.
The previous value doesn't cause any problems because that we now only
use the bulk out endpoint. Set the hardware with the correct value any
way.
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit 7fee72d5 ("uas: Always apply US_FL_NO_ATA_1X quirk to
Seagate devices"), the US_FL_NO_ATA_1X is always set for Seagate devices,
so the per device unusual_uas.h entries for Seagate devices can be
removed.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replacing dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: NVasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Interface drivers like btusb that don't support reset-resume will be
rebound at resume if port was reset. Rebind is done during the pm_ops
.complete callback when probe returns EPROBE_DEFER as default.

Remove the "rebind failed: -517" message.
Device probe will eventually take place later.

[one-liner by Jerry Snitselaar posted in a mailing list question -Mathias]
Suggested-by: NJerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Indeed musl doesn't define old SIGCLD signal name but only new one SIGCHLD.
SIGCHLD is the new POSIX name for that signal so it doesn't change
anything on other libcs.

This fixes this kind of build error:

usbipd.c: In function ‘set_signal’:
usbipd.c:459:12: error: 'SIGCLD' undeclared (first use in this function)
  sigaction(SIGCLD, &act, NULL);
            ^~~~~~
usbipd.c:459:12: note: each undeclared identifier is reported only once
	for each function it appears in
Makefile:407: recipe for target 'usbipd.o' failed
make[3]: *** [usbipd.o] Error 1
Signed-off-by: NJulien BOIBESSOT <julien.boibessot@armadeus.com>
Acked-by: NShuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The fix of "FIXME: Notify the subdrivers..." doesn't actually have any
 real effect. The "FIXME" changed to simple comment.
Signed-off-by: NMikhail Zaytsev <flashed@mail.ru>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: NPravin Shedge <pravin.shedge4linux@gmail.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Using a period after a newline causes bad output.

Miscellanea:

o Coalesce formats too
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Clean up the USB device-node helper that is used to look up a device
node given a parent hub device and a port number. Also pass in a struct
usb_device as first argument to provide some type checking.

Give the helper the more descriptive name usb_of_get_device_node(),
which matches the new usb_of_get_interface_node() helper that is used to
look up a second type of of child node from a USB device.

Note that the terms "device node" and "interface node" are defined and
used by the OF Recommended Practice for USB.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This code looks up a USB device node from a given parent USB device but
never dropped its reference to the returned node.

As only the address of the node is used for a later matching, the
reference can be dropped immediately.

Note that this trigger implementation confuses the description of the
USB device connected to a port with the port itself (which does not have
a device-tree representation).

Fixes: 4f04c210 ("usb: core: read USB ports from DT in the usbport LED trigger driver")
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add OF device-tree support for USB interfaces.

USB "interface nodes" are children of USB "device nodes" and are
identified by an interface number and a configuration value:

	&usb1 { /* host controller */
		dev1: device@1 { /* device at port 1 */
			compatible = "usb1234,5678";
			reg = <1>;

			#address-cells = <2>;
			#size-cells = <0>;

			interface@0,2 { /* interface 0 of configuration 2 */
				compatible = "usbif1234,5678.config2.0";
				reg = <0 2>;
			};
		};
	};

The configuration component is not included in the textual
representation of an interface-node unit address for configuration 1:

	&dev1 {
		interface@0 {	/* interface 0 of configuration 1 */
			compatible = "usbif1234,5678.config1.0";
			reg = <0 1>;
		};
	};

When a USB device of class 0 or 9 (hub) has only a single configuration
with a single interface, a special case "combined node" is used instead
of a device node with an interface node:

	&usb1 {
		device@2 {
			compatible = "usb1234,abcd";
			reg = <2>;
		};
	};

Combined nodes are shared by the two device structures representing the
USB device and its interface in the kernel's device model.

Note that, as for device nodes, the compatible strings for interface
nodes are currently not used.

For more details see "Open Firmware Recommended Practice: Universal
Serial Bus Version 1" and the binding documentation.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a new binding for USB interface nodes, which are child nodes of
USB device nodes and addressed by interface number and configuration
value tuples.

Also add a new binding for USB combined nodes, which are special case
nodes for simple USB devices for which they replace the device and
interface nodes.

For completeness, define the already used terms "host-controller node",
"device node" and "hub node".
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The expectation in the FUSB302 driver is that a TX_SUCCESS event
should occur after a message has been sent, but before a GCRCSENT
event is raised to indicate successful receipt of a message from
the partner. However in some circumstances it is possible to see
the hardware raise a GCRCSENT event before a TX_SUCCESS event
is raised. The upshot of this is that the GCRCSENT handling portion
of code ends up reporting the GoodCRC message to TCPM because the
TX_SUCCESS event hasn't yet arrived to trigger a consumption of it.
When TX_SUCCESS is then raised by the chip it ends up consuming the
actual message that was meant for TCPM, and this incorrect sequence
results in a hard reset from TCPM.

To avoid this problem, this commit updates the message reading
code to check whether a GoodCRC message was received or not. Based
on this check it will either report that the previous transmission
has completed or it will pass the msg data to TCPM for futher
processing. This way the incorrect ordering of the events no longer
matters.
Signed-off-by: NAdam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If probe fails, fusb302_debugfs_exit is called making it impossible
to view any logs so use normal dev_err for any error messages during
probe.
Signed-off-by: NMats Karrman <mats.dev.list@gmail.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Trivial fix to spelling mistake in error message text
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Variable t is assigned but never read, it is redundant and therefore
can be removed. Cleans up clang warning:

drivers/usb/host/whci/asl.c:106:3: warning: Value stored to 't' is
never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

USB devices should work just fine when they don't support language id.

Lower the log level so user won't panic in the future.

BugLink: https://bugs.launchpad.net/bugs/1729618Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ARM fixes from Russell King:

 - LPAE fixes for kernel-readonly regions

 - Fix for get_user_pages_fast on LPAE systems

 - avoid tying decompressor to a particular platform if DEBUG_LL is
   enabled

 - BUG if we attempt to return to userspace but the to-be-restored PSR
   value keeps us in privileged mode (defeating an issue that ftracetest
   found)

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: BUG if jumping to usermode address in kernel mode
  ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
  ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
  ARM: make decompressor debug output user selectable
  ARM: fix get_user_pages_fast

Pull irq fixes from Thomas Glexiner:

 - unbreak the irq trigger type check for legacy platforms

 - a handful fixes for ARM GIC v3/4 interrupt controllers

 - a few trivial fixes all over the place

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/matrix: Make - vs ?: Precedence explicit
  irqchip/imgpdc: Use resource_size function on resource object
  irqchip/qcom: Fix u32 comparison with value less than zero
  irqchip/exiu: Fix return value check in exiu_init()
  irqchip/gic-v3-its: Remove artificial dependency on PCI
  irqchip/gic-v4: Add forward definition of struct irq_domain_ops
  irqchip/gic-v3: pr_err() strings should end with newlines
  irqchip/s3c24xx: pr_err() strings should end with newlines
  irqchip/gic-v3: Fix ppi-partitions lookup
  irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
  genirq: Track whether the trigger type has been set

Pull misc x86 fixes from Ingo Molnar:
 - topology enumeration fixes
 - KASAN fix
 - two entry fixes (not yet the big series related to KASLR)
 - remove obsolete code
 - instruction decoder fix
 - better /dev/mem sanity checks, hopefully working better this time
 - pkeys fixes
 - two ACPI fixes
 - 5-level paging related fixes
 - UMIP fixes that should make application visible faults more debuggable
 - boot fix for weird virtualization environment

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
  x86/decoder: Add new TEST instruction pattern
  x86/PCI: Remove unused HyperTransport interrupt support
  x86/umip: Fix insn_get_code_seg_params()'s return value
  x86/boot/KASLR: Remove unused variable
  x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
  x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
  x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
  x86/pkeys/selftests: Fix protection keys write() warning
  x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
  x86/mpx/selftests: Fix up weird arrays
  x86/pkeys: Update documentation about availability
  x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
  x86/smpboot: Fix __max_logical_packages estimate
  x86/topology: Avoid wasting 128k for package id array
  perf/x86/intel/uncore: Cache logical pkg id in uncore driver
  x86/acpi: Reduce code duplication in mp_override_legacy_irq()
  x86/acpi: Handle SCI interrupts above legacy space gracefully
  x86/boot: Fix boot failure when SMP MP-table is based at 0
  x86/mm: Limit mmap() of /dev/mem to valid physical addresses
  x86/selftests: Add test for mapping placement for 5-level paging
  ...

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes: a documentation fix, a Sparse warning fix and a debugging
  fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Fix task state recording/printout
  sched/deadline: Don't use dubious signed bitfields
  sched/deadline: Fix the description of runtime accounting in the documentation

Pull perf fixes from Ingo Molnar:
 "Misc fixes: two PMU driver fixes and a memory leak fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix memory leak triggered by perf --namespace
  perf/x86/intel/uncore: Add event constraint for BDX PCU
  perf/x86/intel: Hide TSX events when RTM is not supported

Pull static key fix from Ingo Molnar:
 "Fix a boot warning related to bad init ordering of the static keys
  self-test"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  jump_label: Invoke jump_label_test() via early_initcall()

Pull objtool fixes from Ingo Molnar:
 "A handful of objtool fixes, most of them related to making the UAPI
  header-syncing warnings easier to read and easier to act upon"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/headers: Sync objtool UAPI header
  objtool: Fix cross-build
  objtool: Move kernel headers/code sync check to a script
  objtool: Move synced files to their original relative locations
  objtool: Make unreachable annotation inline asms explicitly volatile
  objtool: Add a comment for the unreachable annotation macros

Detect if we are returning to usermode via the normal kernel exit paths
but the saved PSR value indicates that we are in kernel mode.  This
could occur due to corrupted stack state, which has been observed with
"ftracetest".

This ensures that we catch the problem case before we get to user code.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>

Pull timer updates from Thomas Gleixner:

 - The final conversion of timer wheel timers to timer_setup().

   A few manual conversions and a large coccinelle assisted sweep and
   the removal of the old initialization mechanisms and the related
   code.

 - Remove the now unused VSYSCALL update code

 - Fix permissions of /proc/timer_list. I still need to get rid of that
   file completely

 - Rename a misnomed clocksource function and remove a stale declaration

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
  m68k/macboing: Fix missed timer callback assignment
  treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
  timer: Remove redundant __setup_timer*() macros
  timer: Pass function down to initialization routines
  timer: Remove unused data arguments from macros
  timer: Switch callback prototype to take struct timer_list * argument
  timer: Pass timer_list pointer to callbacks unconditionally
  Coccinelle: Remove setup_timer.cocci
  timer: Remove setup_*timer() interface
  timer: Remove init_timer() interface
  treewide: setup_timer() -> timer_setup() (2 field)
  treewide: setup_timer() -> timer_setup()
  treewide: init_timer() -> setup_timer()
  treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
  s390: cmm: Convert timers to use timer_setup()
  lightnvm: Convert timers to use timer_setup()
  drivers/net: cris: Convert timers to use timer_setup()
  drm/vc4: Convert timers to use timer_setup()
  block/laptop_mode: Convert timers to use timer_setup()
  net/atm/mpc: Avoid open-coded assignment of timer callback function
  ...

Pull ARC updates from Vineet Gupta:

 - more changes for HS48 cores: supporting MMUv5, detecting new
   micro-arch gizmos

 - axs10x platform wiring up reset driver merged in this cycle

 - ARC perf driver optimizations

* tag 'arc-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: perf: avoid vmalloc backed mmap
  ARCv2: perf: optimize given that num counters <= 32
  ARCv2: perf: tweak overflow interrupt
  ARC: [plat-axs10x] DTS: Add reset controller node to manage ethernet reset
  ARCv2: boot log: updates for HS48: dual-issue, ECC, Loop Buffer
  ARCv2: Accomodate HS48 MMUv5 by relaxing MMU ver checking
  ARC: [plat-axs10x] auto-select AXS101 or AXS103 given the  ISA config

Pull more Kbuild updates from Masahiro Yamada:

 - use 'pwd' instead of '/bin/pwd' for portability

 - clean up Makefiles

 - fix ld-option for clang

 - fix malloc'ed data size in Kconfig

 - fix parallel building along with coccicheck

 - fix a minor issue of package building

 - prompt to use "rpm-pkg" instead of "rpm"

 - clean up *.i and *.lst patterns by "make clean"

* tag 'kbuild-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: drop $(extra-y) from real-objs-y
  kbuild: clean up *.i and *.lst patterns by make clean
  kbuild: rpm: prompt to use "rpm-pkg" if "rpm" target is used
  kbuild: pkg: use --transform option to prefix paths in tar
  coccinelle: fix parallel build with CHECK=scripts/coccicheck
  kconfig/symbol.c: use correct pointer type argument for sizeof
  kbuild: Set KBUILD_CFLAGS before incl. arch Makefile
  kbuild: remove all dummy assignments to obj-
  kbuild: create built-in.o automatically if parent directory wants it
  kbuild: /bin/pwd -> pwd

Pull AFS fixes from David Howells:

 - Make AFS file locking work again.

 - Don't write to a page that's being written out, but wait for it to
   complete.

 - Do d_drop() and d_add() in the right places.

 - Put keys on error paths.

 - Remove some redundant code.

* tag 'afs-fixes-20171124' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: remove redundant assignment of dvnode to itself
  afs: cell: Remove unnecessary code in afs_lookup_cell
  afs: Fix signal handling in some file ops
  afs: Fix some dentry handling in dir ops and missing key_puts
  afs: Make afs_write_begin() avoid writing to a page that's being stored
  afs: Fix file locking

Pull KVM updates from Radim Krčmář:
 "Trimmed second batch of KVM changes for Linux 4.15:

   - GICv4 Support for KVM/ARM

   - re-introduce support for CPUs without virtual NMI (cc stable) and
     allow testing of KVM without virtual NMI on available CPUs

   - fix long-standing performance issues with assigned devices on AMD
     (cc stable)"

* tag 'kvm-4.15-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
  kvm: vmx: Allow disabling virtual NMI support
  kvm: vmx: Reinstate support for CPUs without virtual NMI
  KVM: SVM: obey guest PAT
  KVM: arm/arm64: Don't queue VLPIs on INV/INVALL
  KVM: arm/arm64: Fix GICv4 ITS initialization issues
  KVM: arm/arm64: GICv4: Theory of operations
  KVM: arm/arm64: GICv4: Enable VLPI support
  KVM: arm/arm64: GICv4: Prevent userspace from changing doorbell affinity
  KVM: arm/arm64: GICv4: Prevent a VM using GICv4 from being saved
  KVM: arm/arm64: GICv4: Enable virtual cpuif if VLPIs can be delivered
  KVM: arm/arm64: GICv4: Hook vPE scheduling into vgic flush/sync
  KVM: arm/arm64: GICv4: Use the doorbell interrupt as an unblocking source
  KVM: arm/arm64: GICv4: Add doorbell interrupt handling
  KVM: arm/arm64: GICv4: Use pending_last as a scheduling hint
  KVM: arm/arm64: GICv4: Handle INVALL applied to a vPE
  KVM: arm/arm64: GICv4: Propagate property updates to VLPIs
  KVM: arm/arm64: GICv4: Handle MOVALL applied to a vPE
  KVM: arm/arm64: GICv4: Handle CLEAR applied to a VLPI
  KVM: arm/arm64: GICv4: Propagate affinity changes to the physical ITS
  KVM: arm/arm64: GICv4: Unmap VLPI when freeing an LPI
  ...

Pull powerpc fixes from Michael Ellerman:
 "A small batch of fixes, about 50% tagged for stable and the rest for
  recently merged code.

  There's one more fix for the >128T handling on hash. Once a process
  had requested a single mmap above 128T we would then always search
  above 128T. The correct behaviour is to consider the hint address in
  isolation for each mmap request.

  Then a couple of fixes for the IMC PMU, a missing EXPORT_SYMBOL in
  VAS, a fix for STRICT_KERNEL_RWX on 32-bit, and a fix to correctly
  identify P9 DD2.1 but in code that is currently not used by default.

  Thanks to: Aneesh Kumar K.V, Christophe Leroy, Madhavan Srinivasan,
  Sukadev Bhattiprolu"

* tag 'powerpc-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Fix Power9 DD2.1 logic in DT CPU features
  powerpc/perf: Fix IMC_MAX_PMU macro
  powerpc/perf: Fix pmu_count to count only nest imc pmus
  powerpc: Fix boot on BOOK3S_32 with CONFIG_STRICT_KERNEL_RWX
  powerpc/perf/imc: Use cpu_to_node() not topology_physical_package_id()
  powerpc/vas: Export chip_to_vas_id()
  powerpc/64s/slice: Use addr limit when computing slice mask

Pull SCSI target updates from Nicholas Bellinger:

 "This series is predominantly bug-fixes, with a few small improvements
  that have been outstanding over the last release cycle.

  As usual, the associated bug-fixes have CC' tags for stable.

  Also, things have been particularly quiet wrt new developments the
  last months, with most folks continuing to focus on stability atop 4.x
  stable kernels for their respective production configurations.

  Also at this point, the stable trees have been synced up with
  mainline. This will continue to be a priority, as production users
  tend to run exclusively atop stable kernels, a few releases behind
  mainline.

  The highlights include:

   - Fix PR PREEMPT_AND_ABORT null pointer dereference regression in
     v4.11+ (tangwenji)

   - Fix OOPs during removing TCMU device (Xiubo Li + Zhang Zhuoyu)

   - Add netlink command reply supported option for each device (Kenjiro
     Nakayama)

   - cxgbit: Abort the TCP connection in case of data out timeout (Varun
     Prakash)

   - Fix PR/ALUA file path truncation (David Disseldorp)

   - Fix double se_cmd completion during ->cmd_time_out (Mike Christie)

   - Fix QUEUE_FULL + SCSI task attribute handling in 4.1+ (Bryant Ly +
     nab)

   - Fix quiese during transport_write_pending_qf endless loop (nab)

   - Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK in 3.14+
     (Don White + nab)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (35 commits)
  tcmu: Add a missing unlock on an error path
  tcmu: Fix some memory corruption
  iscsi-target: Fix non-immediate TMR reference leak
  iscsi-target: Make TASK_REASSIGN use proper se_cmd->cmd_kref
  target: Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK
  target: Fix quiese during transport_write_pending_qf endless loop
  target: Fix caw_sem leak in transport_generic_request_failure
  target: Fix QUEUE_FULL + SCSI task attribute handling
  iSCSI-target: Use common error handling code in iscsi_decode_text_input()
  target/iscsi: Detect conn_cmd_list corruption early
  target/iscsi: Fix a race condition in iscsit_add_reject_from_cmd()
  target/iscsi: Modify iscsit_do_crypto_hash_buf() prototype
  target/iscsi: Fix endianness in an error message
  target/iscsi: Use min() in iscsit_dump_data_payload() instead of open-coding it
  target/iscsi: Define OFFLOAD_BUF_SIZE once
  target: Inline transport_put_cmd()
  target: Suppress gcc 7 fallthrough warnings
  target: Move a declaration of a global variable into a header file
  tcmu: fix double se_cmd completion
  target: return SAM_STAT_TASK_SET_FULL for TCM_OUT_OF_RESOURCES
  ...

This fixes a missed function prototype callback from the timer conversions.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20171123221902.GA75727@beast

The assignment of dvnode to itself is redundant and can be removed.
Cleans up warning detected by cppcheck:

fs/afs/dir.c:975: (warning) Redundant assignment of 'dvnode' to itself.

Fixes: d2ddc776 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Due to recent changes this piece of code is no longer needed.

Addresses-Coverity-ID: 1462033
Link: https://lkml.kernel.org/r/4923.1510957307@warthog.procyon.org.ukSigned-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>

afs_mkdir(), afs_create(), afs_link() and afs_symlink() all need to drop
the target dentry if a signal causes the operation to be killed immediately
before we try to contact the server.
Signed-off-by: NDavid Howells <dhowells@redhat.com>