- 10 10月, 2008 1 次提交
-
-
由 Steve Sakoman 提交于
Add defconfig for the Gumstix Overo board Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 09 10月, 2008 5 次提交
-
-
由 Steve Sakoman 提交于
This patch adds minimal overo support. Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Syed Mohammed, Khasim 提交于
Add Beagle defconfig Signed-off-by: NSyed Mohammed, Khasim <khasim@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Syed Mohammed, Khasim 提交于
Add minimal Beagle board support. Based on earlier patches by Syed Mohammed Khasim with some fixes from linux-omap tree. Signed-off-by: NSyed Mohammed Khasim <khasim@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Syed Mohammed, Khasim 提交于
Add minimal omap3430 support based on earlier patches from Syed Mohammed Khasim. Also merge in omap34xx SRAM support from Karthik Dasu and use consistent naming for sram init functions. Also do following changes that make 34xx support usable: - Remove unused sram.c functions for 34xx - Rename IRQ_SIR_IRQ to INTCPS_SIR_IRQ and define it locally in entry-macro.S - Update mach-omap2/io.c to support 2420, 2430, and 34xx - Also merge in 34xx GPMC changes to add fields wr_access and wr_data_mux_bus from Adrian Hunter - Remove memory initialization call omap2_init_memory() until until more generic memory initialization patches are posted. It's OK to rely on bootloader initialization until then. Signed-off-by: NSyed Mohammed, Khasim <khasim@ti.com> Signed-off-by: Karthik Dasu<karthik-dp@ti.com> Signed-off-by: NAdrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Paul Walmsley 提交于
Fix sparse warnings in mach-omap2/irq.c. Fix by defining intc_bank_write_reg() and intc_bank_read_reg(), and convert INTC module register access to use them rather than __raw_{read,write}l. Also clear up some checkpatch warnings involving includes from asm/ rather than linux/. Signed-off-by: NPaul Walmsley <paul@pwsan.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 06 10月, 2008 6 次提交
-
-
由 Tony Lindgren 提交于
Misc updates from linux-omap tree, mostly to update common device initialization and add missing defines from linux-omap tree. Also some changes to make room for adding 34xx in following patches. Note that the I2C resources are now set up in arch/arm/plat-omap/i2c.c helper, and can be removed from devices.c. Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Paul Walmsley 提交于
Fix sparse, checkpatch warnings fro GPMC code. Also change to use ioremap, and add missing function prototypes to gpmc.h. Signed-off-by: NPaul Walmsley <paul@pwsan.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Vikram Pandita 提交于
This patch adds pinmux support for OMAP3. Incorporated review comments from Tony to make mux_value as bit mask. Tested on 3430SDP. Also merge in adding of I2C pins from Jarkko Nikula. Acked-by: NAnand Gadiyar <gadiyar@ti.com> Signed-off-by: NVikram Pandita <vikram.pandita@ti.com> Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Tony Lindgren 提交于
This allows to get rid of the ifdefs and will allow simpler CPU detection in the future. Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Tony Lindgren 提交于
Some register offsets are different for 242x and 243x. This will allow compiling sleep code for both chips into the same kernel. Pass the addresses for SDRC_DDLA_CTRL and SDRC_POWER to the omap24xx_cpu_suspend instead of loading the values since the only. Also fix a bug to call omap2_sram_suspend with the value of SDRC_DLLA_CTRL instead of the address as that's what omap24xx_cpu_suspend expects to determine between DDR and SDR. This bug has not been noticed as the boards seem to have DDR instead of SDR. Note that some PM patches are still missing. The PM patches will be added later on once the base files are in sync with linux-omap tree. Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Jouni Hogander 提交于
This patch adds common function to enable/disable omap2/3 uart clocks. Enabled uarts are passed by bootloader in atags and clocks for these enabled uarts are touched. Signed-off-by: NJouni Hogander <jouni.hogander@nokia.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 03 10月, 2008 2 次提交
-
-
由 Russell King 提交于
Merge branch 'omap-rmk' into omap-all
-
由 Russell King 提交于
Merge branch 'omap2-clock' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git Merge branch 'omap2-clock' into omap-all
-
- 06 9月, 2008 12 次提交
-
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
gpio.c wilfully casts physical addresses to void __iomem * and then fixes them up at runtime using: bank->base = IO_ADDRESS(bank->base); where accesses prior to this fixup are via omap_read/omap_write, and after are by __raw_read/__raw_write. This doesn't lend itself to static checking, nor to easy understanding of the code. And so, OMAP_MPUIO_BASE gets to be the right type - integer like since it's a physical address, not a MMIO pointer. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
We're now assigning/comparing void __iomem pointers with void __iomem pointer variables. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
OMAP1_IO_ADDRESS(), OMAP2_IO_ADDRESS() and IO_ADDRESS() returns cookies for use with __raw_{read|write}* for accessing registers. Therefore, these macros should return (void __iomem *) cookies, not integer values. Doing this improves typechecking, and means we can find those places where, eg, DMA controllers are incorrectly given virtual addresses to DMA to, or physical addresses are thrown through a virtual to physical address translation. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
When omap_udc is also incorporated, this macro will no longer be used. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
A function to contain common code for the size of the resource we need to allocate or free. OMAP ports need 22 bytes rather than the standard 8 bytes. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Make is_omap_port() take the uart_8250_port structure so it can do whatever test it desires. Convert the test to compare the physical addresses rather than virtual addresses. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 05 9月, 2008 1 次提交
-
-
由 Russell King 提交于
mcbsp is confused as to what takes a physical or virtual address. Fix the two instances where it gets it wrong. Acked-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 04 9月, 2008 2 次提交
-
-
由 Huang Weiyi 提交于
The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION. arch/arm/plat-mxc/clock.c This patch removes the said #include <version.h>. Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
drivers/usb/host/ohci-omap.c: In function 'ohci_omap_init': drivers/usb/host/ohci-omap.c:228: error: 'start_hnp' undeclared (first use in this function) Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 03 9月, 2008 11 次提交
-
-
由 Russell King 提交于
arch/arm/plat-omap/gpio.c: In function '_omap_gpio_init': arch/arm/plat-omap/gpio.c:1492: error: 'omap_mpuio_device' undeclared (first use in this function) Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: ipsec: Fix deadlock in xfrm_state management. ipv: Re-enable IP when MTU > 68 net/xfrm: Use an IS_ERR test rather than a NULL test ath9: Fix ath_rx_flush_tid() for IRQs disabled kernel warning message. ath9k: Incorrect key used when group and pairwise ciphers are different. rt2x00: Compiler warning unmasked by fix of BUILD_BUG_ON mac80211: Fix debugfs union misuse and pointer corruption wireless/libertas/if_cs.c: fix memory leaks orinoco: Multicast to the specified addresses iwlwifi: fix 64bit platform firmware loading iwlwifi: fix apm_stop (wrong bit polarity for FLAG_INIT_DONE) iwlwifi: workaround interrupt handling no some platforms iwlwifi: do not use GFP_DMA in iwl_tx_queue_init net/wireless/Kconfig: clarify the description for CONFIG_WIRELESS_EXT_SYSFS net: Unbreak userspace usage of linux/mroute.h pkt_sched: Fix locking of qdisc_root with qdisc_root_sleeping_lock() ipv6: When we droped a packet, we should return NET_RX_DROP instead of 0
-
由 Thomas Gleixner 提交于
Larry Finger reported at http://lkml.org/lkml/2008/9/1/90: An ancient laptop of mine started throwing errors from b43legacy when I started using 2.6.27 on it. This has been bisected to commit bfc0f594 "x86: merge tsc calibration". The unification of the TSC code adopted mostly the 64bit code, which prefers PMTIMER/HPET over the PIT calibration. Larrys system has an AMD K6 CPU. Such systems are known to have PMTIMER incarnations which run at double speed. This results in a miscalibration of the TSC by factor 0.5. So the resulting calibrated CPU/TSC speed is half of the real CPU speed, which means that the TSC based delay loop will run half the time it should run. That might explain why the b43legacy driver went berserk. On the other hand we know about systems, where the PIT based calibration results in random crap due to heavy SMI/SMM disturbance. On those systems the PMTIMER/HPET based calibration logic with SMI detection shows better results. According to Alok also virtualized systems suffer from the PIT calibration method. The solution is to use a more wreckage aware aproach than the current either/or decision. 1) reimplement the retry loop which was dropped from the 32bit code during the merge. It repeats the calibration and selects the lowest frequency value as this is probably the closest estimate to the real frequency 2) Monitor the delta of the TSC values in the delay loop which waits for the PIT counter to reach zero. If the maximum value is significantly different from the minimum, then we have a pretty safe indicator that the loop was disturbed by an SMI. 3) keep the pmtimer/hpet reference as a backup solution for systems where the SMI disturbance is a permanent point of failure for PIT based calibration 4) do the loop iteration for both methods, record the lowest value and decide after all iterations finished. 5) Set a clear preference to PIT based calibration when the result makes sense. The implementation does the reference calibration based on HPET/PMTIMER around the delay, which is necessary for the PIT anyway, but keeps separate TSC values to ensure the "independency" of the resulting calibration values. Tested on various 32bit/64bit machines including Geode 266Mhz, AMD K6 (affected machine with a double speed pmtimer which I grabbed out of the dump), Pentium class machines and AMD/Intel 64 bit boxen. Bisected-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Tested-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 David S. Miller 提交于
Ever since commit 4c563f76 ("[XFRM]: Speed up xfrm_policy and xfrm_state walking") it is illegal to call __xfrm_state_destroy (and thus xfrm_state_put()) with xfrm_state_lock held. If we do, we'll deadlock since we have the lock already and __xfrm_state_destroy() tries to take it again. Fix this by pushing the xfrm_state_put() calls after the lock is dropped. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Morton 提交于
Fix a bug reported by and diagnosed by Aaron Straus. This is a regression intruduced into 2.6.26 by commit adc782da Author: Matt Mackall <mpm@selenic.com> Date: Tue Apr 29 01:03:07 2008 -0700 random: simplify and rename credit_entropy_store credit_entropy_bits() does: spin_lock_irqsave(&r->lock, flags); ... if (r->entropy_count > r->poolinfo->POOLBITS) r->entropy_count = r->poolinfo->POOLBITS; so there is a time window in which this BUG_ON(): static size_t account(struct entropy_store *r, size_t nbytes, int min, int reserved) { unsigned long flags; BUG_ON(r->entropy_count > r->poolinfo->POOLBITS); /* Hold lock while accounting */ spin_lock_irqsave(&r->lock, flags); can trigger. We could fix this by moving the assertion inside the lock, but it seems safer and saner to revert to the old behaviour wherein entropy_store.entropy_count at no time exceeds entropy_store.poolinfo->POOLBITS. Reported-by: NAaron Straus <aaron@merfinllc.com> Cc: Matt Mackall <mpm@selenic.com> Cc: Theodore Ts'o <tytso@mit.edu> Cc: <stable@kernel.org> [2.6.26.x] Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 John Kacur 提交于
Make PM_QOS and CPU_IDLE play nicer when run with the RT-Preempt kernel. The purpose of the patch is to remove the spin_lock around the read in the function pm_qos_requirement - since spinlocks can sleep in -rt and this function is called from idle. CPU_IDLE polls the target_value's of some of the pm_qos parameters from the idle loop causing sleeping locking warnings. Changing the target_value to an atomic avoids this issue. Remove the spinlock in pm_qos_requirement by making target_value an atomic type. Signed-off-by: Nmark gross <mgross@linux.intel.com> Signed-off-by: NJohn Kacur <jkacur@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Rafael J. Wysocki 提交于
Update rtc-cmos shutdown handling to leave RTC alarms active, resolving http://bugzilla.kernel.org/show_bug.cgi?id=11411 on several boards. There are still some systems where the ACPI event handling doesn't cooperate. (Possibly related to bugid 11312, reporting the spontaneous disabling of RTC events.) Bug 11411 reported that changes to work around some ACPI event issues broke wake-from-S5 handling, as used for DVR applications. (They like to power off, then wake later to record programs.) [yakui.zhao@intel.com: add shutdown for PNP devices] [dbrownell@users.sourceforge.net: update comments] Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl> Signed-off-by: NZhao Yakui <yakui.zhao@intel.com> Signed-off-by: NZhang Rui <rui.zhang@intel.com> Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Cc: Stefan Bauer <stefan.bauer@cs.tu-chemnitz.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Russ Anderson 提交于
Document files in /sys/firmware/sgi_uv/. Signed-off-by: NRuss Anderson <rja@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Acked-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mike Christie 提交于
I got this patch through Red Hat's bugzilla from the bug submitter and patch creator. I have just fixed it up so it applies without fuzz to upstream kernels. Original patch and description from Shyam kumar Iyer: The issue [ibft module not displaying targets with short names] is because of an offset calculatation error in the iscsi_ibft.c code. Due to this error directory structure for the target in /sys/firmware/ibft does not get created and so the initiator is unable to connect to the target. Note that this bug surfaced only with an name that had a short section at the end. eg: "iqn.1984-05.com.dell:dell". It did not surface when the iqn's had a longer section at the end. eg: "iqn.2001-04.com.example:storage.disk2.sys1.xyz" So, the eot_offset was calculated such that an extra 48 bytes i.e. the size of the ibft_header which has already been accounted was subtracted twice. This was not evident with longer iqn names because they would overshoot the total ibft length more than 48 bytes and thus would escape the bug. Signed-off-by: NShyam Kumar Iyer <shyam_iyer@dell.com> Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Cc: Konrad Rzeszutek <konrad@virtualiron.com> Cc: Peter Jones <pjones@redhat.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jan Altenberg 提交于
commit 945185a6 ("rtc: rtc_time_to_tm: use unsigned arithmetic") changed the some types in rtc_time_to_tm() to unsigned: void rtc_time_to_tm(unsigned long time, struct rtc_time *tm) { - register int days, month, year; + unsigned int days, month, year; This doesn't work for all cases, because days is checked for < 0 later on: if (days < 0) { year -= 1; days += 365 + LEAP_YEAR(year); } I think the correct fix would be to keep days signed and do an appropriate cast later on. Signed-off-by: NJan Altenberg <jan.altenberg@linutronix.de> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Cc: Dmitri Vorobiev <dmitri.vorobiev@gmail.com> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Krzysztof Helt 提交于
If there are more then one graphics card handled by the tdfxfb driver the name of the frame buffer overruns reserved size. Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-